ANSWERS : Technology

I need you help bright minds of Instructables!
I want to make a very small Tesla coil and I have the right schematic! But I still remain a n00b in electronics...
This schematic is used in:

• Nano Tesla Coil I http://www.extremeelectronics.co.uk/coils/nt/
• Nano Tesla Coil II http://www.extremeelectronics.co.uk/coils/nt/index.php?page=nanotess2.php

Help me build the schematic below... I would be very grateful to one who makes the schemactic in Eagle or other program that shows everything connected together.
Thanks you very much!
Stanislav A.K.A. Comodore

Comments

[mino nano]

hi i'me new hear i realy whant to make a small inexspensive tesla coil out of household items
please can somebody help me
with simple plans

[morphic cu ion]

can you give the schematic for nano tess II and III please

[Xellers]

If you can't get the parts for this, then try Steve Ward's micro SSTC. I built one from a computer power supply and some free samples (The 555 timer and UCC37322 Driver)!

[thermoelectric]

I will try to make the schematic in Eagle....

[comodore]

Thanks, I am very thankful! Thank you so much!

[thermoelectric]

You're welcome

[thermoelectric]

This should be it

I hope I didn't miss any connections
PS the VSS and VDD are the power for the IC and the connections for the power.....

[comodore]

Yay! Thanks! I think I can make everything out here... What value is VSS and VDD??? Thanks!

[thermoelectric]

VDD= Positive
VSS= Negative

Those values you might use again so here's a link

[comodore]

ooo OK Thanks!

[thermoelectric]

You're welcome, Be sure to tell me (and Plas) if it works...

[comodore]

Will do, but still, I can't find all the components I need to realize this project... :(

[thermoelectric]

Yeah...

[comodore]

Do you know any on-line electronic store that ships to Europe?

[thermoelectric]

Possibly Farnell, Plasmana gets his parts from them and he's in the United Kingdom...

[comodore]

Yea, I know that site and they don't have those diodes... I checked.... Thanks!

[thermoelectric]

Oh, Just search them i\on Google, You will most likely get a supplier of them.

[comodore]

Yea, good idea, will do that! Thanks!

[thermoelectric]

You're welcome...

[rippinblaise]

do you have the eagle file, not the jpg? if you do, pm me.

[thermoelectric]

Willyou be using the Eagle file to make a PCB out of? If you are, some of the parts aren't real.... (The driver IC, I had to just put a line where the enable pin should have been because I couldn't find that chip in the Eagle library. )

[rippinblaise]

that is what i was going to use it for you could download the library it's in or i could i guess can i have the file though?

[thermoelectric]

I'll give you the file but the thing with the enable pin won't work on a board because it is not the right part...

[Goodhart]

Are 2 interrupters involved, or just one attached at the enable pin?

[comodore]

I am really not shore, my guess is 1.

[miiwii3]

look I'm an electronic genius i can build anything electrical but this is a little difficut. you know what as I was wrighting this I think I just figured it out tell me if I'm right or not. You need to connect the driver a from the ocilator to the drive a on th diver same with the drive b. Now the interupter cable has a output cable called enables connect that to enables on the driver. I forgott to check to check the links links so I'll post another comment to end your troubles. looks cool to so I'll have to build one too.

[guyfrom7up]

very subtle there :P yellow wire-goes to RF ground (say, a copper water pipe, don't use the 3rd prong in your house because it might damage all of the equipment in your house, but it might not matter since this is tiny) in the schematic simply connetc A to A and B to B, lol, not rocket science here. darn straight it goes from 12 volts to a higher voltage :P but unlike a conventional coil where there's high voltage in the primary (several kilovolts) it's all done at a lower voltage (say, 12 volts in this case) at higher current. More about the circuit: The 4 diodes are for preventing inductive kickback (ie large negative voltage) uhhh... I don't feel like looking up the chips now, but basically it self resonates (duh)

[comodore]

Could you please tell me are the components(HEF4049 ; IXDD414 ; UF5408) that I found on this site: http://export.farnell.com/ , the components that I need for this project?

• HEF4049 http://export.farnell.com/nxp/hef4049bp/4000-locmos-4049-dip16-15v/dp/385281
• IXDD414

Can't find it, do you know a store that sells these and ships them to Europe...

• UF5408

Here there a re 2 group and one group has 1 product and the other 3, witch, precisely diode do I need???
http://export.farnell.com/jsp/search/browse.jsp;jsessionid=YDEIFA2WGNGCYCQLCIRZKBQ?N=0&Ntk=gensearch_001&Ntt=UF5408&Ntx=&suggestions=false&_requestid=527443

Thanks!
Grateful comodore!

[guyfrom7up]

HEF4049 is a chip containing multiples inverters (high in=low out, low in = high out, high=12 volts, low = gnd/0 volts) that have high current capabilities.

IXDD414 is a highspeed mosfet/igbt driver

UF5408 are very fast diodes

your links all lead to a country page, probably cause I'm in the US

[comodore]

your links all lead to a country page, probably cause I'm in the US
-Yea, that you chose your country and you enter the site...
Please enter the site and do a search for :

• HEF4049 (only 1 product and yes, it's a chip)
• IXDD414 ( 0 products, where can I find that diode, do you sell them???) :D
• UF5408 ( 4 products in total separated in 2 groups)

Please, look at the products and tell me if they are the right ones???
Thank you!

[comodore]

The small Tesla coil with the spark gap that you are making, what did you make the top out of...aluminium foil??? Thanks!

[guyfrom7up]

I carved a toroid out of styrofoam, dunked it in polyurethane, and then coated it with aluminum foil. I think I'm going to make a new one, this one had too many bumps.

[comodore]

Cool, a real proses.... You are really into this stuff! :D

[comodore]

Thanks guyfrom7up! I knew where to connect A and B but what about the Interrupter, where does the enable wire go??? Also, Vcc, whats that? Thanks !

[guyfrom7up]

Vcc in this case is probably +12 volts In most schematics, though, like with microcontrollers and such, Vcc is 5 volts. Most common values for Vcc: 3.3, 5, 12 In this case 12

[comodore]

Thanks!

[miiwii3]

http://www.instructables.com/id/Step_By_Step_Plans_to_Building_a_250000_Volt_Tesl/connect the enables in the interuppter to the 2 enables in the driver circut. the 2 antennaes must go to the coils a.k.a. the white wires in the second pic the yellow wire must be ground. I don't know 4 sure if i am right so build the circut how i told you and build a tesla coil how this guy did. The way I see it is your are boosting the power off a 12-18 vlt battery to a highr voltage a.k.a. the driver circut and connect the out put to the tesla coil. I only did this for the small one with a door nob for a ball so i don't know if this will work fo the the second mini tesla coil. I hope this helped you If it didn't go to my account and post your Question there.

[comodore]

Thanks miiwii3...you did help a lot...now its time to gather materials and get this project started... :D

[miiwii3]

that is the link at the top to how to build tthe coil sorry I don't have the schematic program on ths computer.

[comodore]

OK, the pictures re to blurry but I think I can make out everything.... Thanks!

[Kiteman]

Try this link.

[comodore]

You gave me a link to member Plasmana... Why?

[Kiteman]

He's our resident high-voltage expert. Have a look at his Instructables.

[comodore]

I know... I asked him first on his orange board but he wasn't shore... He told me he could build a small Tesla coil easy but he doesn't have the $$....

[The_Vinninator]

so do you want the schematic explained? or do you want a drawing? or a picture? or what exactly? can you be slightly more specific? also, does this have anything to do with the electromagnet you were making?

[comodore]

do you want a drawing?

• Yes, that would be very very very helpful....Thanks
  

or a picture?

• Shore, why not... :D
  

do you want the schematic explained?

• If I get the drawing or a picture, I think that will not be needed...
  

can you be slightly more specific?

• Yes, look up... :-D
  

also, does this have anything to do with the electromagnet you were making?

• No...I am just working on multiple projects at the time...first I want to do the Tesla coil and than....
  

Thanks!

[The_Vinninator]

sorry, this might take a while you're not it a rush, are you?

[comodore]

No rush, take your time... Thanks!

[The_Vinninator]

done! hope you can understand this a little better

[comodore]

huh..Thanks! :D I think I can make out everything.... :P Do you think you could use Photo Shop or some other program and cut each segment and attach it, maybe... i am very grateful for this drawing but when working with High Voltage I want to be 100% I am connecting everything as it should be! Thanks!

[The_Vinninator]

you mean zoom in on each part? sure, I can do that

[comodore]

Could you please tell me are the components(HEF4049 ; IXDD414 ; UF5408) that I found on this site:
http://export.farnell.com/ , the components that I need for this project?

• HEF4049 http://export.farnell.com/nxp/hef4049bp/4000-locmos-4049-dip16-15v/dp/385281
• IXDD414

Can't find it, do you know a store that sells these and ships them to Europe...

• UF5408

Here there a re 2 group and one group has 1 product and the other 3, witch, precisely diode do I need???
http://export.farnell.com/jsp/search/browse.jsp;jsessionid=YDEIFA2WGNGCYCQLCIRZKBQ?N=0&Ntk=gensearch_001&Ntt=UF5408&Ntx=&suggestions=false&_requestid=527443

Thanks!
Grateful comodore!

[The_Vinninator]

diodes are very forgiving if you use the wrong one by accident, it shouldn't change the process much at all I'd tell you, but the site is down right now, sorry pal I'm working on the image this is taking really long

[comodore]

I'm working on the image -Yay! Thanks a lot! Take your time, I am not in a hurry! :D

[The_Vinninator]

sorry, I just checked the schematic anything with that serial number will work so ya, you've got what you want

[comodore]

Yay, so...I think I will order some of these in a few days... And about the IXDD414??? Do you know where I can find it or do you know a replacement... The diodes UF5408...Witch one from the 2 groups you suggest I use? Thanks!

[comodore]

Yea, or maybe use Eagle or some other program for more clarity.... thanks!