how do u get aluminium powder

how do u get aluminium powder? do u just grind aluminium into a fine powder or what??

sort by: active | newest | oldest
LasVegas8 years ago
You could also break open an old Etch-A-Sketch.
IF i break open my phone with the etch-a-sketch app running, will that work??
ttoddd LasVegas7 years ago
I did and I'ts full of tiny plastic beads which are imposible to separate out of the aluminum powder beacause they are so small.
. The beads will probably float in water if they are plastic. You may have to add a wetting agent (eg, soap) to get the Al to break the surface tension and sink.
has anybody tested this out? I'd be interested in the results.
could you just mix aluminum foil and bleach together in a jar to make aluminum powder?
That's called an acid bomb, and it's very dangerous.
Which is called an acid bomb? Mixing bleach with aluminium?
no. mixing red devil lye drain cleaner with water and aluminum foil in a soda bottle. have it next to a lit torch made out of a tree branch. big flaming boom. lots of shrapnel. caustic liquid flying everywhere. Bad.
bleach is sodium hypochlorite. i don't know what it would do,(probably nothing!) but it wouldn't grind it up, which is what you have to do. it might make aluminum oxide.(aluminum oxide doesn't do anything.)
Is aluminium oxide soluble in water?
no. it is soluble in drain cleaner, and that's how hydrogen making from aluminum cans works.
i broke open my Etch-A-Sketch and i only got little aluminum balls
and if you mix bleach and foil will there be any danger doing that?
Those are iron fillings.
No... It's aluminum powder.
Really? Weird, I know the stuff in the Magna Doodle is iron fillings though.
Yes, Magna-Doodle is magnetic (iron) and grubby-looking, but Etch-A-Sketch is aluminium.
See here for some Etch-A-Sketch artwork...
RynoTHEpyro3 years ago
Here is the name brand of what your looking for in regards to AL powder in paint stores. West System 420. its mostly used in marine resine coating.
hope this helps.
Inspiracy8 years ago
I saw someone make it once out of just, straight up aluminum pieces, some drain cleaner and some water. I can't remember what kinda drain cleaner it was. He put the drain cleaner and the water inside of a glass, when he inserted the aluminum it started to bubble really violently and give off a pretty fair amount of fumes. When the water bubbled away, all that was left was aluminum powder. This is a violent process. The guy who showed me this said that he had blown himself up a few times in doing it. The explosion is blue, meaning that it's a force explosion instead of a hot one, which I suppose is why he was alive to show it off. Very dangerous, it's best to just buy the powder.
that makes aluminum oxide, not aluminum.
So basically the only choice we have (short of building some machine to melt a compound of aluminium to perform electrolysis on it) is to break open Etch a Sketchs?
electrolysis of aluminum oxide will lave you with a hunk of pure aluminum, not powder. you can buy aluminum powder in a large paint store or wal-mart. yes you could break open etch a sketch's, but i don't know how fine it is, and how much there is.
Or you could do this==> http://www.instructables.com/id/Making-German-Dark-Aluminum-Powder-from-Foil/
 What would the labeling or brand name be for aluminum powder in a paint store or walmart so i know what to look for? 
What was his midichlorian count? Or is 'force explosion' a Sith power?
lol funny...
he blew up because Al and drain cleaner make hydrogen and I think chlorine the hydrogen is flamibal and burns blue/orange I have seen both witch is weird.
it doesn't make chlorine. lye(drain cleaner) strips aluminum of it's oxide layer, therefor allowing it to steal the water's oxygen and leaves the hydrogen free. i know it burns orange when created this way, but it burns blue in a pure ratio with oxygen(as in electrolysis). the black scum is dissolved aluminum oxide.
yah hydrogen + chlorine = BOOM!!!!
And oxygen...
Hey check out my instrctable its this exact experiment here
except this one produces black sludge, How useful!

I think your mistaken.
It is worth noting that breathing fine metals is hazardous in multiple ways. Please use good ventilation when you're blowing yourself up.
roadkill905 years ago
just a question how much aluminum powder is in a Etch A Sketch
Iron filings i do believe. Etch A Sketches use a magnet
jtobako doomduc5 years ago
That's magnex or something like that. Etch a Sketch uses dials to rub the powder off the screen.
doomduc jtobako5 years ago
i always thought it was a small magnet and iron filings but i looked it up and you were right sorry about the bother sir.
Taost5 years ago
Nah, I checked Walmart, they don't have Aluminum powder. The closest thing I could find was Aluminum Free Baking powder...>.>
jtobako Taost5 years ago
Auto section, radiator stop-leak. Comes in a little tube of gray powder.
I have made aluminum for thermite by cutting thick pieces of aluminum with a carbide circular saw and collecting the shavings. You could use a ball mill to reduce that to a fine powder.
KentsOkay8 years ago
You can buy it at a paint store.
Yes, it's used to make "aluminum paint," or to make other paints reflect more infrared. It's vastly easier to buy it at a paint store than to grind it yourself, especially if you need a fine powder. (And it comes nicely contained in a jar or can, rather than spread all over your work environment and the insides of your lungs, like when you grind your own.) If you need extremely fine metal powders, you can find them at places that sell molding and casting materials. (They're used for making "cold cast metals," i.e., polyester or epoxy mixes contaning much metal that's so finely ground that it looks like solid metal.)
 I think in all the comments we've established that its available in paint stores and possibly walmart, but what labeling or brand or product name are we looking for. I don't wanna walk in not knowing what im looking for and asking suspiciously for finely ground metals.

a relatively easy way to make this (if you have the tools) is to blend or grind aluminium foil in an old coffe grinder/blender, then to ball mill the rough powder that comes out.
sorry, you can only really get into pyro/bomb making if you have a ball mill. its cheaper to make one yourself, btw
if you can't do it this way the best your gonna do is sandpaper a block of aluminium then ginding it with a mortar and pestle. it takes ages and doesn't make lots or at a good quality either.

can u take aluminum foil crush it in a ball sand it with fine sandpaper?? just asking
But then you would have sand in your aluminum. A simpler way is to use a file, but it takes forever.
skywalk216 years ago
I know it sounds stupid, but break open an Etch-A-Sketch or two. they're FILLED with the shtuff
Forces6 years ago
Found this, Removing it from aluminum from aluminum paint, around 15%-20% of the paint mass (depending on brand), taking into consideration that some aluminum is lost in the extraction process. I have harvested aluminum from both TremClad and Rust-Oleum 7715 brands, with the former having a slightly higher yield. Before beginning the harvesting process, allow the tin of paint to sit undisturbed for several weeks to allow metallic aluminum to settle to the bottom. To begin the process, carefully remove the lid from the container and use a turkey baster (or other similar siphoning device) to carefully draw away most of the linseed oil base. Some aluminum particles will be drawn up, but this is not important - the net loss will not be significant. Fill the tin with acetone, then stir contents, using a wooden craft stick, for several minutes. Make sure and scrape the settled aluminum off the entire bottom and sides. Replace the lid and allow to stand overnight undisturbed. The acetone is next drawn off using the baster. Refill the container with acetone and repeat the cleansing process. The purpose of the cleansing is to remove any remaining linseed oil which, if not removed, will cause the dried aluminum to form into hard clumps. After the acetone has been drawn off a second time, tilt the tin slightly and use a piece of paper towel to "wick" away the remaining pool of acetone. The remaining "wet slurry" of aluminum flakes and acetone are then scooped into a suitable polyethylene pan and spread out to allow the acetone to evaporate. Occasional stirring will speed up the process which will take a couple of days at room temperature to fully dry. Using the convex side of a spoon, break up the clumps to a fine powder. Using a fine nylon kitchen sifter, sift the powder to remove any clumps. Continue until all the aluminum has been harvested as a fine powder. Store in a suitable sealed container.
Sedgewick178 years ago
That guy you watched make the powder also made hydrogen gas, and if he blew himself up, he was doing it in a closed room (NOT SMART).The easiest way I know of is to grind an aluminum soda can on a bench grinder and a cup to catch to filings. Just out or curiosity what are you tiring to make Thermite, or a rocket?
how do you make termite?
thermite is made up of iron oxide which is rust mixed with aluminum powder get about 8 grams iron oxide and 3 grams aluminum powder, one of those etch a sketch is really good for pure aluminum powder and iron oxide you could buy or (borrow) from a clay maker as its used to pigment the clay. once you've made thermite buy just mixing both them powders together you will need something to light it i.e a strip of magnesium as magnesium is a low igniting point but high burning temp and thermite is a high igniting point it works well ir you could try a fuse out of a fire work. THERMITE BURNS AT OVER 2000 centigrade dont try and stop the reaction by throwing water on it either as you will end up with molten metal everywhere and probaly on yourself.
iknowad6 years ago
This is how I make aluminum powder. I get a crappy blender and blend aluminum foil in it until the peices are relatively fine. 20 minutes at full speed should do the trick. I come back and ball mill my coarse aluminum powder with a mix of 5% stearin and 5% graphite. I ball mill the contents for 2-3 weeks ,and I can get powder 400-500 mesh. BTW I made my own ball mill.
REA iknowad6 years ago
takes a quarter of the time with the Blendtecblender. 37000 rpm of what appears to be titanium blades FTW!!!
Will it blend? Yes!
that thing can end the war in iraq while making a delicious pinaple-banana smoothie!
Out of freakin' IEDs and AK-47s!
hey can u get aluminum foil and just grind it up in an old blender or coffee grinder
Sandisk1duo7 years ago
Grind an old aluminum heatsink... do it on a newspapar
demonfox37 years ago
and all my paint stores dont sell it...have they made it illegal in some states/counties or am i just unlucky? also, are thos ice packs that u squeeze illegal 2? casue i can find thjose at any sporting goods stores either (need it for the inner bag that contains the NH4NO3)
u gotta go to a walgreens, target, or walmart and look 4 instant cold packs all of those stores shud hav them look very carefully or ask 4 help and 4 Al powder idk im still lookin into that lol but ill let u know wen i find out good luck
demonfox37 years ago
I need aluminum powder to make a flash bang
heimo7 years ago
I am busy working on a machine that kan make large amounts of aluminium realy fast if it works I will post an instructable on it and I know it will work becuse this is an industral proses but i still have to work out all the details becuse this is can be realy dagerous and you can burn yourself but where I live paint stors dont sell aluminium so there is no alternative but if it works i will be able to make a couple of pounds of aluminium in 30 mins best of all thes prosess dont involve these words grinding ,filing or sanding I will be sure to keep you all posted on progress
ninefingers7 years ago
I never could buy flake Al powder. Most stores are wise to you. Aluma-Seal for radiators is supposed to contain it--but they won't tell you. Many Al Paints can be left for 5 weeks in an upright position, then the linseed oil siphoned off with a turkey baster. Rinse the sludge in bottom with acetone well, and spread out to dry. Another is: Get two rolls Aluminum foil. Tear into 1" squares Using an old (preferably Oster brand) blender, grind a handful up. This will take a lot of time, as you can't grind dry for more than a minute. Allow to cool 5 minutes. Add foil, grind again. With patience, you can get about 40 mesh Powder this way, which works good for most things. Sieve it through a tea strainer. If you need it smaller, get or borrow a rock tumbler, add about 200 3/8" steel shot (available as slingshot ammo in hardware or sporting goods store--or, use up to 1/2" ball bearings) and, grind about 4 weeks. Stop and open lid once every day to allow dust to oxidise slightly--this is a safety factor. You will get about 400 mesh this way. Shake through a brass Mr. Coffee filter. AND--wear a good dust mask, always--this stuff almost choked Buddy Ebsen to death on the set of "The Wizard of Oz."
owenaero7 years ago
DO NOT GRIND ALUMINUM ON A GRINDING WHEEL. I have a machine shop grinding ALU on these wheels that are not made for grinding ALU causes the alum to pack in to the pores of the wheel causing expanschen and cracking in the wheel and at high speed the wheel can come apart I know in the industry that people have been severely hurt AND killed from not using proper wheels and flying apart and chunks entering the body. USE EXTREEM CAUTION!!!!!! DOING THIS. looking out for your safety.
yallrfags7 years ago
anyone trying to grind up aluminum might as well give up now if they are trying to make anything even a little bit powerful then you must have the most possible surface area so logicaly they only way is a chemical brakedown of the element
i did it the hard way did it the really hard way, with a piece of aluminum and a steel file but you could also crack open a etcha sketch
steven078 years ago
So making thermite? or just want powder? electrolysis is always possible (from some Al salt)- however you wont make much (but if your making thermite you'll probably already have an electrolytic rust maker so at least you'll have all the equipment) can you buy the powder as face paint or am i mistaken?
jtobako8 years ago
Um, yah. The trick is to grind it up without it sticking back into itself. Try RogueSci.com, I remember a forum post there about an easy way to grind aluminum foil into powder.