Step 4: Program the Arduino

The following code will cycle through turning on each relay:

void setup() {


void loop() {

<p>Thank you for showing how to make a shield from parts to settle right on to the Arduino. It would never have occurred to me to do this, let alone figure out how.</p>
can i use in4007 diode instead of the one which you use
Would it be possible to use this circuit with light switches instead? I dont mean the ones on the light itself, but the wall switches.
This is definitely possible. There would be two ways to do that. You could directly connect the light switches to the circuit, or you can mount a servo to each light switch that flips the light switch so you don't have to open up the wiring in your wall.
In SA we use 220-250V, what relays would I have to use for that amount of voltage?
Most 5 volt relays are most likely not rated for that much voltage. Your best bet (to my knowledge) would be to use TIP120 transistors instead of the 2n3904's and use 12 volt relays instead of the 5 volt ones. It would probably be best for you to contact someone that has experience with that kind of voltage (Mine is 110). Remember to be safe, never work on a mains voltage projects while it is plugged in, and to insulate ALL live wires using electrical tape. Have fun!
Thanks man, do you know anyone on instructables that I could ask??
If you are really set on making this project, you can't go wrong with asking a question. Again, I do not feel comfortable giving people advice with mains voltage circuits because they are not my specialty. I will do a bit of research and consult my father (he is pretty good with mains voltage).
Most relays have contact ratings... are these rated for 120VAC?
Nevermind, I found info on the contacts 125VAC @ 1A. Gotta watch the amperage or you'll weld the contact.
Way to go!!! You are on Hack-A-Day!!!<br>http://hackaday.com/2011/12/18/controlling-your-christmas-lights-without-ever-getting-off-the-couch/<br>Cheers!
Life long dream fulfilled! I am happy!!
Your scematic doesn't show any loads on the AC lines, which means that as each relay closes it will cause a dead short across the AC supply! Noobs to AC might not know this, with disasterous results!
Thanks for pointing this out! I actually thought I updated the schematic but I guess it didn't upload properly. Thanks for the comment!
You're welcome.
Then link it up to the internet or a timer, so the light turn on when your away from home
<a href="https://www.instructables.com/id/Tweeting-Christmas-Tree/" rel="nofollow">https://www.instructables.com/id/Tweeting-Christmas-Tree/</a>
You might want to add a rectifying diode across the relay pins. When current stops moving through the coil (the adruino pin is brought low) you get a flyback effect which could smoke your android. Also a project encasement would be great - you can pick them up at radio shack for about 5-10 bucks depending on size (a definite requirement when working with mains voltage and current). Finally, you mention the npn transistors but I don't see you using them anywhere. Were you maybe thinking of using them as a current controlling device for the relay coils? Otherwise, great tut.
I was going to put a diode between the leads for suppressing the voltage transient, but I did not have the proper value(1N914). The relays that I used are pretty small that the chances of a voltage transient are slim to none, although it is a good practice to place the diode between the coil leads of a relay. At the time, I did not have enough time or money to buy an enclosure but do plan on buying one and updating the instructable. I had two schematics, one that had the transistors and one that had the outlets, I figured that the one with the electrical outlets was wiser to put on because the schematic clearly shows how to hook them up and the text describes how to hookup the transistors. The transistors turn on and off the external power to the relays. Thanks for the comment!
If it has a coil or any inductive part then it will create a voltage spike when you remove current. Inductors resist current change, so when you remove power from a coil and give the residual current no place to travel a voltage spike will form. By placing a diode &quot;backwards&quot; you give a path for the current to slowly fade. Here is a scope cap of a 5v I just tested without a diode, pk-pkv =183v.<br>
Wow! Thanks for letting me know, I will put this in the tutorial and make sure to switch the schematic around ASAP. Thanks for the comment!
Not a problem at all :) I generally start with &quot;fast&quot; diodes like a 1n4148, but rectifiers like the 1n400X series work just fine too. Most pks I measure on those 5v relays are about 59v but, every once in a while they sure get up there. Luckily they are very short (IIRC that one was 147uSec).
I was trying to test the transient's voltage on my multi-meter but I guess it was way too fast for my meter. I really want a logic analyzer!
That scope cap was taken with a QuantAsylum100 we are evaluating for carrying in our shop. For a usb scope and analyzer I'm pretty impressed with it, but you cant go wrong with a hacked Rigol :) A scope is a very handy tool while not necessary, when you do get one, you'll wonder how you did anything without it :)
I meant &quot;smoke your arduino&quot;, I have Android on my mind today.
Good idea Robot Lover. However I feel a heads-up call is warranted to my local fire department if I so chose to try this. - Electricity scares me. That and propane bbq's... Thanks for starting the Instructable Advent Calendar 2011 - I look forward to seeing all the entries. - oh what fun.
Great job!

About This Instructable




Bio: I love making things. I always found electronics and stuff like that fun. When I was little I always took apart my toys and put ... More »
More by Robot Lover:Christmas Advent Calendar! How to Make Paper Snowflakes! 3 Channel arduino Powered Christmas Light Controller! 
Add instructable to: