Instructables

9v Altoid USB Charger

Picture of 9v Altoid USB Charger
Just one more 9v USB charger!
 
Remove these adsRemove these ads by Signing Up

Step 1: Materials

Picture of Materials
PICT0101.JPG
- Altoid tin
- 5v regulator
- Wire
- Small LED
- Soldier
- Female USB
- Epoxy (i used J.B. Weld)
- Small slide switch
- Tape

Step 2: Perpare The Tin

Trace the outline of the USB on the bottom of the tin near the edge. Mark the spot where you want to put the LED. Drill it out with a drill bit slightly larger than the led. Use a drimmal to cut out the hole for the USB. Sand the surface smooth with sand paper then use a smaller girt to polish it.

Step 3: The Circuit

chargers 004.JPG
chargers 009.JPG
The circuit is very simple. The usb has 4 pins you will only use the 1st and 4th one. The regulator has 3 pins the 1st one is the ground the 2nd one it out and the 3rd one is in. Now follow the diagram.

Step 5: Finshed

Picture of Finshed
This is the finished product!
1-40 of 60Next »
matu_pro31 year ago
is also for ipod touch 4g
Also, for most iphones the middle two connections need to have 2V running to them for it to "recognize" it as a charging device.
Diode is essential. Without it it can drain your phone's battery. Found this out the hard way.
dude can you use an old computer female usb
no der
yes you can....as long as you use it right
yes you can....as long as you use it right
Hey do you know where i can buy a "soldier" radioshack doesn't carry them should i call the marines?
rryapolov3 years ago
Will this schematic work?
Skematics.png
nope, ground have to be connected to middle pin and from last pin there is output 5v ,i ll post shematics and how to do it on my page
also check this post http://www.instructables.com/id/How-to-get-your-iPod-to-charge-with-your-homemade-/
wire LED parallel not serial
tealk1 year ago
how.much exactly does regulator output? i tried 2 of them and voltage they output is 5.7-6 v. i get those from computer power suply
tealk1 year ago
how.much exactly does regulator output? i tried 2 of them and voltage they output is 5.7-6 v. i get those from computer power suply
DoctorDv2 years ago
I am working on a charger and i was wondering doesn't a 9v put off too much current and won't it damage an ipod?
-Doctordv
Deanozaur3 years ago
I am just wondering, since most led's I have are 3.7 volts, using even five volts will eventually ruin the led. Could you email me or post a schematic of where to add a resistor to help lengthen the life of the led, so it doesn't melt? Also, I want to add a second, brighter led that is blue. How do I attach that to the same power source (the 9v battery) and use a different momentary switch? I saw a youtube video where the guy attached 2 leds and a usb all to the same power source. I'll give you the link so you can see what I'm talking about: http://www.youtube.com/watch?v=TVU2JmRpF58

If you could also answer the second question in an email or post a schematic, it would be much appreciated. I already have a 100 ohms resistor, and I already own all of the led's.
Add the resistor to either the anode or cathode (either pin) of the LED.
LinuxH4x0r6 years ago
This will probably fry your device. Don't try it!
it probably wont, unless its from the 90's
actually, it will fry it, it fried my zune. which was luckilly still under warranty.
they are talking about ipods not zunes
yea? i know that dude, they charge on the same voltage, and the same amperage, learn it first. I've been building these for years. for a variety of devices, usb doesnt change.
(insert smart alec reply here)
no.. it wouldn't the power of this thing doesn't even have the power to fry a toaster
it wont fry an ipod on the back it says 5-30 volts
Bran LinuxH4x0r6 years ago
I can't seem to tell much of a difference, though I've only skimmed through both iBles. What's the reason this one will screw the device up?
LinuxH4x0r Bran6 years ago
I think its that it has too high current, but I'm not sure. I'd rather use the mintyboost.
Bran LinuxH4x0r6 years ago
Yeah, 500mA is max.
LinuxH4x0r Bran6 years ago
7805 puts out 1amp (1000mA)
Bran LinuxH4x0r6 years ago
Er....500mA is what most chargers put out....
LinuxH4x0r Bran6 years ago
No, I mean a 7805 regulator puts out 1A.
1A max. The device will only draw what it needs. My iPod charger puts out a max of 1 amp, but I charge my cellphone and GPS off of it. In theory you could put two USB ports on it, but I wouldn't do that. Also, a 9v battery will probably not be able to put out 1amp, and certainly not for long.
Good pictures for this instructable though.
yep zuixro is right, but I just read the instructable and there's a problem with it. The led should be in parallel with the output, not in series. Doing it in the setup shown it'll either cause the led to blow up really fast (i'm not sure whenever people say leds blow up, they just smoke) or the output will only be limited to 30 ma (not likely since there's no resistor.
The device being charged will only draw what it needs. This charger won't work with ipod touch/ iphone. These devices detect USB packages and wont charge unless they are connected to a computer or pulled high (aka trick)
Deanozaur3 years ago
One comment says that the led has to be in parallel with the output, not in series. Can you tell me if that's true?
ashishkapur4 years ago

can it charge psp , coz m not able 2 charge it even after putting it in usb mode with usb charge on........plz help!!!!!!!

the easiest way would to find a pin that fits in the charger port and put that on the end of the usb
Wire543216 years ago
mount 5v regulator using heat sink compound. BUT WARNING CASE MAY BE COME HOT!!! THANKS
You shouldn't need a heatsink for this particular application because the voltage regulator is not regulating a very high voltage or a voltage in the high end of its operating range so it shouldn't, in theory, become very hot.
It won't become too hot. The only time one of these regulators will become unbearable is when you are dropping something like 30 volts down to 5. It will dissipate the excess voltage as heat.
1-40 of 60Next »