Instructables
Picture of A Simple and Inexpensive Cheese Press
Cheesemaking is an amazing alchemy that transforms milk into a profusion of different textures and flavors.  The entryway for me was ricotta, an easy and forgiving cheese to make with no fancy equipment or supplies needed.  Mozzarella came next, also very do-able with supermarket ingredients and kitchen utensils.  I was so pleased with the results of these first forays into cheesemaking that I decided to go all in and try making hard (as in consistency) cheeses like cheddar.  

There is a certain amount of gear that you need in order to go to the next level.   One of the main pieces of equipment necessary for making harder cheeses is a cheese press to squeeze the curds under a specific pressure for a set amount of time.  I found cheese presses for sale online but they were expensive ($70-$275).  I decided that making my own was the way to go. I wanted something that would be able to handle up to two pounds of curds and generate up to 50 lbs of pressure.  I took my inspiration from a couple of similar press designs I found online and added my own ideas.  After a little experimentation I ended up with a press that was simple to use and inexpensive to build using basic tools.   Expect to spend between $10 to $25 depending on how much stuff you have at home already.

As with any set of instructions this will guide you to replicate what I made.  Don't feel constrained by my ideas though, you should modify my design to meet your needs any way you see fit.

Check out my blog for other stuff I've been making including a cheese cave for ageing all this cheese I'm going to be making with my new press...
 
Remove these adsRemove these ads by Signing Up
1-40 of 43Next »
Scottbus made it!6 months ago

Great design! I didn't have any hardwood, so I substituted some cutting board material that is dishwasher safe and can be sanitized. Thanks so much for the inspiration and Instructable.

20140424_193204.jpg
lynn0759 Scottbus5 months ago

That is great! Question: since you are using two layers of the cutting board, did you use adhesive between to avoid moisture slipping between? If so, what is appropriate?

Scottbus lynn07595 months ago

I didn't use any adhesive. I left them separable so that the press can be disassembled and sanitized in a dishwasher. If I glued them, there would always be seams and crevices that might not get clean, and I wouldn't know what to use that would be dishwasher safe.

The bolts on the threaded rod hold the bottom two layers on the base together, while pressure from the springs holds the others together.

spike3579 (author)  Scottbus5 months ago

Hey that looks awesome! Thanks for sharing your build. Happy cheese making.

rbezileyesterday

How do you print the file? I log into Pro and it is not a PDF or does anything download. Do I need to pay for the service to print the instructions? BTW, great cheese press.

I've just made one of these with a slight mod. I used a 22mm thick food grade polyothylene chopping board instead of wood. Cheese is susceptable to bacteria and it's a lot easier to clean. Dishwasher proof too! Only cost me 17 euros from amazon too.
spike3579 (author)  Mickleblade1 year ago
Cool! Post a picture if you have one. The only reason I didn't use HDPE instead of wood was because I found that the plastic tended be less rigid and bend from the tension from the springs. I'll be interested to hear if you have any problems or if the plastic works just fine for you.

So far so good, I doubled up on the plastic, so it is not as flexible as a single sheet, minimal bending up to jack cheese pressure.

I did the same thing! Great minds think alike...

terranchild5 months ago

I assume the drill bits are to match the diameter of the threaded rod. Am I correct?

seziegle9 months ago
I am having trouble locating the right springs. Do you have more information about the ones you used such as free length, outside diameter, etc.? Also thanks so much for posting this!
Scottbus seziegle6 months ago

I looked at two big box hardware stores for springs and couldn't find
any suitable, sure enough, the first independent hardware store I went
to had just the ticket. I had to shorten them with a Dremel, but other
than that they were perfect.

spike3579 (author)  seziegle9 months ago
I've found that independent hardware stores are more likely to carry springs than the big box stores. I gave my cheese press away so I can't measure the springs. Off the top of my head I would say they were roughly 2" tall x 3/4" dia. If you can't find any springs locally then try McMaster Carr.  Post a picture if you get a press built.  I'd love to see it.
kffrost9 months ago
I loved this and built my own to get started in cheese making last October. A modification I made yesterday was to make different height "stackable" molds (using leftover PVC as I did with the first six inch mold I made). I found this MUCH easier to remove and reload the cheese during the pressing stage. I added 2, 3 and 4 inch tall molds. I was just running out of room in the mold when making anything other than cheddar with 2 or more gallons. Thanks for your design!
spike3579 (author)  kffrost9 months ago
I'm glad to hear the design worked for you. I like the modular approach. That makes a lot of sense, I have read that PVC shouldn't be used in contact with foods. I don't know what the chances are that anything bad will leach out but it might be wise to line them with a plastic bag or something deemed food safe. That's why I went with the pitcher as a mold. I'd love to see a picture of your press if you get a chance to post it.
jfbaily10 months ago
Eddie j , Does R stand for radius In your equation!
lhardwick1 year ago
Get a plastic lid that is a bit bigger than the mold, make (heat and bend or just cut) a little pourer bit, then sit the mold on that so the curds can drain into the sink and you won't have to use plastic wrap and put it in the sink - especially if you have it pressing a cheese for 12 hours or so!
spike3579 (author)  lhardwick1 year ago
Great idea! Especially because everyone has a plastic lid sitting around that doesn't match any containers anymore.
spike3579 (author) 1 year ago
The more parallel the better but work with what you can get. The worst that will happen is that the cheese cloth will bulge around the top plate some. Not a biggie.
streetrod51 year ago
Spike, I am planning on making one of these, but haven't found any plastic pitchers that have perfectly parallel sides - is that critical? Great 'Able!
Frederbee2 years ago
I love your press, the book on cheese-making I just picked up called for it in every one of my favourite cheeses, and the prices of the presses terrified me (what if I only use it once and then stop?). Thank you so much for your instructable, when I finish making mine I'll definitely post pictures. Depending on how well I use it, I may end up making more than one for bigger cheese!

Also, isn't it odd that the spell-check on the comment box underscores the word instructable?
spike3579 (author)  Frederbee2 years ago
Good luck with your press. My cheese making arc was pretty short lived so I'm glad I didn't shell out $200 for a press. A friend of mine uses one I made her weekly. She even joined a goat co-op!
Eddie j2 years ago
I took a 3 hr class on cheese making (Gouda) is what we made. he told us that 50 lbs is not always 50lbs it all depends on the surface area of your mold. for
example a 4" round mold will have less surface area than a 6" round mold. which means that it will also have more pessure on it. to find out how many sq inches you have in a round mold is to PI 3.14 X R X R = sq in
Now I am trying to find out the PSI on the soft press and the PSI on the hard press.
spike3579 (author)  Eddie j2 years ago
I never thought about that. Post your findings on the correct PSI in the comments so we can use the right ones!
Anna W3 years ago
Excellent! Beautifully crafted, well documented and explained, and just what I've been looking for. I should get one made before the cold sets in. Thank-you!

P.s. Have you any further suggestions/modifications since then? And how goes the cheese-making?
spike3579 (author)  Anna W3 years ago
I did change the scale on the next one I made to make it simpler and more elegant. You can see it here. I've actually done very little cheese making over the past year. My cheese cave right now has returned to it's old life as an overflow fridge for long term storage. Currently it's holding a bunch of different pickles and some duck leg confit.
mslaynie3 years ago
Is it really this easy to make cheese? I mean, I don't mean it's easy, but... this actually looks like something I could do! I'm speechless...
craigbw3 years ago
This is my next project in 2011. I can also envision using the press for applications other than cheesemaking! Thank you for doing all the design work.
spike3579 (author)  craigbw3 years ago
What sort of applications? Evil ones?
aeray3 years ago
Cheesemaking rocks, as does your press. I'll be building one of these well-designed-and-executed presses once I get my meat-curing fix. Meat and sausage curing has been distracting me from cheesemaking for a while now (and the kraut, and the kimchi, etc). Thanks!
spike3579 (author)  aeray3 years ago
I hear you. I 've been to sausageland too. In fact, I need to post my sausage stuffer design. The kitchenaid stuffer is a total pain. I've made fresh sausage but am dreaming of cured sausages. Cheesemaking got in the way of my meat curing desires...
aeray spike35793 years ago
I just finished some bresaola and corned elk, and I'm working on a prosciutto and some guanciale. Elk landjager is next, and I'll be using the kitchenaid as well, so hurry up and post the stuffer design!
tbcross3 years ago
I love love love this ible!!! Did I mention I have goats? I had been dreading shelling out the $ for presses once we start getting milk. This is brilliant! Thanks
spike3579 (author)  tbcross3 years ago
MMM goat's milk. I'm jealous. (except for the whole caring for and milking part)
You'll be making Chevre in no time. I don't think you even need a press or a mold for it.

I'm actually considering getting goats...
I've got a recipe for queso blanco and one for mozzarella. My step-dad is from Wisconsin and he influenced my eating habits greatly, ....I eat cheddar on my pancakes even! I've got mini's Nigerian Dwarf and Pygmy so I am hoping for milk next spring.
This is great! I've been wanting to get into cheese making but was a little intimidated.
spike3579 (author)  Chicken Girl3 years ago
If you can handle chickens you can certainly manage some milk in a pot. It doesn't squawk or flap around at all.
zack2473 years ago
I love cheese, but i don't think making one of these will be done by me.
great work on the cheese press, and it looks like the cheese turned out great too!
Ronyon3 years ago
spike3579:BTW, your blog is great, as is your wifes, and I have just spent a couple nice hours on perusing them, and the links from them...
jprewitt63 years ago
I like your press, especially the fine detail of the wood, etc.
1-40 of 43Next »