Introduction: Airsoft Silencer

Give a general description of the Instructableis my homemade beretta 92 fs spring airsoft silencer. I would say that the total reduction is something like 30%-40%.

Step 1: Materials

You will need the following materials and tools to complete this project.

Materials:
a length of 1 inch or bigger diameter thin-wall pvc pipe
1x mini (12 oz) gatorade cap
1x 2L coke bottle cap
1x expo dry erase marker
a bit of pipe insulation
epoxy or some other wicked strong glue


Tools:
a rounded file
a flat file
scisors
hack saw
clamp(useful for holding stuf togeather while drying and holding stuff while sawing it in half)

Step 2: Finding the Right Pipe

I found that a 1 inch diameter thin-wall pvc pipe worked fine with this gun. I would recoment that you don't make the silencer longer than the gun itself.

Step 3: Finding the Right Size End Cap.

I found that a mini Gatorade bottle cap and a 2L coke bottle cap fit perfectly. Fust put the coke cap inside the Gatorade cap and glue them together. I used a five minute epoxy to securely hold them together. You want a very strong glue for this part. Anything less will cause the cap to fail in later steps.

Step 4: Finding an Adpter for the Muzzle of the Gun.

I found that the orange tip had a diameter of roughly 5/8 inches. I searched around my house and found that an expo dry erase marker had the perfect diameter. I pulled out the back with a pair of needle-nose pliers. I pulled out the ink foam thing and then pulled the felt tip out of the front. I then cut the marker tip off so I had a small 5/8 inch diameter tube. i used my hacksaw to cut the tube. it's stiffer than it looks.

Step 5: Fitting the Adapter to the Caps

I drilled a 5/8inch hole into the caps but found that the hole wasn't big enough for the expo marker so i filed it into a rough circle untill it fit VERY TIGHTLY ONTO THE EXPO MARKER. This is very important because otherwise you will beed to glue this as well.

Step 6: Finding the Right Silencing Material

I used a piece of pipe insulatiion for my silencing material. i had to cut it down a little, but it fit in the end. try to make a hole about 1/2 inches in diameter tough the middle of the silencer so there is room for the bb to fly.

Step 7: Final Assembly

This sept is very easy. Simply slide the assembled expo marker and caps into the pvc pipe and pipe insulator. if you want to glue the cap and marker to the pipe, go right ahead. I didn't to allow for future modifications and for easy replacement of parts.

Comments

author
Ericharstad made it! (author)2016-09-07

Alanshkop, a real surpressor wouldn't block the iornsights, but airsoft surpressors block the iornsights...........

author
nktish1 made it! (author)nktish12016-09-11

This isn't true, there are specific sights made for using larger cans. Know the facts

author
Alanshkop made it! (author)2015-03-22

No offense but if you look at a real surpressor it does not block the sights but still it looks awesome

author
austin1201 made it! (author)2008-10-02

when I was building 1 and cut my self and had to get stitches

author
pandaboy292 made it! (author)pandaboy2922008-11-03

where did you cut yourself? once i was cutting a pop can with a razor blade and cut my left index finger. it was on the tip, and after about five mineutes it was throbing alot. this was all the night before i flew to flordia. oh boy salt water in a cut is fun.

author

I cut my middle finger off before ?

author
austin1201 made it! (author)austin12012008-11-04

i cut it on my left index finger right were u bend it

author
garrett10 made it! (author)garrett102009-01-10

now way! i was cutting bamboo with a knife and i had my hand under it and i cut it right on the joint.

author
tictaclad made it! (author)tictaclad2011-01-24

one time i was prying something with my knife (i know bad idea) and it folded in on me and i put tissue on and taped it really tight and in the morning it still hadnt stopped bleeding lol

author
Gawane88 made it! (author)Gawane882011-06-22

no way! I was cuting some cardboard with my leathermen and the knife blade
slipped and it sliced one of my joints on my finger and now I'm scarred there.and I'm only 9! i have more scars than my mom!

author
evilmadcow made it! (author)evilmadcow2012-09-02

HOW did THIS get STARTED?

author
Akairsofters1 made it! (author)Akairsofters12011-01-13

Wow Thats hilarious.

author
xXRRAAWWRRXx made it! (author)xXRRAAWWRRXx2010-03-14

slammed all my left hand finger in a car door. new i was in trouble when i heard is click when shut. long story short cut all my fingers pretty deap and i can barley move my pinkie

author
handyman56 made it! (author)handyman562008-10-21

lol!

author
hkuok made it! (author)2013-09-25

I wonder how this works with NBB airsoft guns. I think the KJW MK1 Would be a very nice place to start.

author
glarive made it! (author)2013-08-17

That's a hella project looks great, a nice coat of black paint and your set!

author
coolkidtn made it! (author)2012-12-10

Yes the P311 rocks. I was in an airsoft war, and charged 2 guys. One had a shotgun and the other had an AEG. When I held up my pistol, they ran away. (They ran away because I kept pelting them in the back)

author
linuxkid made it! (author)2012-07-15

You realize this is illegal unless you pay the nfa taxes, right? even having the stuff to make one, along with the intent, and not paying the tax will land you in jail for quite some time. even if it is only airsoft.

author
runthunter246 made it! (author)2009-04-03

what kind of airsoft gun is that???spring or gas or electric?

author
ilpug made it! (author)ilpug2011-09-27

It is a spring gun. My favorite "cheap" spring pistol is the Smith and Wesson 1911 from Walmart. 300 fps, 15 round mag, very durable. Super accurate.

author
h8864 made it! (author)h88642011-12-25

mine is a stinger p311 it was $20 and is 325 fps.

author
ilpug made it! (author)ilpug2011-12-25

Yeah, I just got a HK USP CO2 pistol from Umarex. It is seriously badass.

author
h8864 made it! (author)h88642012-06-09

not as badass as my new r71 repeater.

author
mrwaffles2 made it! (author)mrwaffles22012-01-28

I love stinger p311's i bought two in a challenge kit and so far they are a very good sidearm.

author
superbestknex made it! (author)superbestknex2012-01-17

crossman stinger p311

author
asghdf made it! (author)asghdf2012-04-23

well warrior L96 bolt action is the best

author
superbestknex made it! (author)superbestknex2012-04-24

more expensive the guns were talking about are less than 50 dollars

author
asghdf made it! (author)asghdf2012-04-23

well warrior L96 bolt action is the best

author
Marble of Doom made it! (author)Marble of Doom2009-04-09

says "beretta 92 fs spring" at the top of the page

author
sharlston made it! (author)sharlston2009-06-11

how much was it? i got a 190 fps spring for $14

author
th3gamingkid made it! (author)th3gamingkid2012-02-28

i got a 325 fps spring for 15$ at BIG 5 at X-Mas. :)
its a Desert Brown Camo. Really Good reliable gun.

author
nerfer192 made it! (author)nerfer1922009-07-08

was it a taurus millenieum? mines 180 fps and $15. great gun

author
Senior Waffleman made it! (author)Senior Waffleman2011-04-09

I got s 315fps spring pistol for 20$

author
sharlston made it! (author)sharlston2009-07-09

no its the p329

author
Lowney made it! (author)Lowney2010-01-03

What? I got a p329 for £4.90 as a garden thing (apprently my gas pistol is too powerful for plinking around). £4.90 is about $7 I think

author
sharlston made it! (author)sharlston2010-01-04

i bought 2 for 10 pound

author
Lowney made it! (author)Lowney2010-01-04

I thought you said it was $14

author
sharlston made it! (author)sharlston2010-01-04

on its own it was 7 pound but i bought two for ten pound

author
nerfer192 made it! (author)nerfer1922009-08-09

or a p230? my neighbors getting that one, yay! now we can have fights!

author
Marble of Doom made it! (author)Marble of Doom2009-06-11

I wouldn't know, it's not my gun nor instructable

author
KNEXFRANTIC made it! (author)KNEXFRANTIC2010-01-30

omg i now somone with that but the seetrough version

author
h8864 made it! (author)2012-03-18

if you load more than one to fire it has a *SHOTGUN* effect

author
superbestknex made it! (author)superbestknex2012-03-20

yeah it does

author
halogirl made it! (author)2010-08-06

spring pistols are dum get a gbb pistol

author
ilpug made it! (author)ilpug2011-09-27

Hey, quit hating. Springers are tons of fun, and surprisingly effective if used well.

author
halogirl made it! (author)halogirl2011-10-03

im not hating my first gun was a $20 beretta 92 springer it was fun until i got my all metal gas blow back beretta 92 and then i saw how dum it was

author
ilpug made it! (author)ilpug2011-10-03

dont say you aren't hating when you are. good day sir.

author
dla888 made it! (author)2009-09-19

A real silencer works by allowing the gases emitted from a gun to cool and expand. By packing this silencer with silencing material you are defeating the purpose. The gas that comes out of your aifsoft gun can't expand(decompress) as much as if it were not packed. What I'm getting at is if I were making this I would not use the silencing material. Otherwise it's a great instructable. Much better than the paper one's I make.

author
Thundertydus made it! (author)Thundertydus2009-11-30

Most airsoft guns used such as the one pictured are spring powered, not gas powered

About This Instructable

56,296views

97favorites

License:

More by cyberviper42:120' Bazooka Powered LongshotAirsoft silencer
Add instructable to: