loading
Picture of Another Altoids Guitar
I loved the Altoids guitars made by bumpus and jwilson27. So I decided to make one to give to my brother for his birthday, with a few additions... ROCK ON!!!
 
Remove these adsRemove these ads by Signing Up

Step 1: Materials

Picture of Materials
Projects 048.jpg
Projects 052.jpg
Projects 062.jpg
The materials needed for this project are as follows:
- Altoids tin (eat up!)
- Wooden slats (I used red oak ones from Lowes)
- Guitar tuning pegs (3) (bought a set of six at the local music store)
- Nylon spacers (found in the specialty hardware section)
- Piezo element
- 1/4" audio jack
- Guerilla glue, hot glue, super glue... (get the picture?)
- Electric guitar strings
- Guitar strap buttons (2)
- At least 12oz. of ice cold liquid creativity *optional, but recommended

The tools I used were as follows:
- Dremel tool with router bit and small cutting wheel bit
- Jigsaw
- Bar clamps
- Drill
- Screwdriver

Step 2: Basic Form

Picture of Basic Form
Projects 044.jpg
Projects 045.jpg
First, take the empty Altoids tin and cut a slot in the side you want the neck to be on. (keep in mind the orientation of the logo on the tin) This slot should be just big enough for one wooden slat to fit into. I used the router bit on my dremel tool, which seemed to work pretty well.

Once this is done, cut a length of wood the length of the neck and headstock, plus the length it will extend into the tin (be sure to leave enough room inside the tin to accomodate the audio jack)

Moisten the end of the slat, and use guerilla glue to secure the wood to the inside of the tin. Clamp them together, and let the glue fully cure.

Cut another piece of wood to the length spanning from the tin to the end of the previous piece. Finally, cut one more piece of wood to span from the tin to the end of the neck (leave enough room for the tuning pegs in the headstock) When measuring these, be sure to leave enough space away from the tin so it will open and close.

Moisten and sandwich the two additional pieces of wood on top of the first with guerilla glue in between. Once again, clamp them all together with bar clamps and let the glue fully cure.

You now have the basic guitar form. Give yourself a congratulatory pat on the back, and play a little air guitar (anything by Journey should do just fine)

Step 3: Adding the details

Measure and drill holes for the tuning pegs, and secure them onto the headstock.

Drill a hole in the tin for the audio jack, and mount it. I had to cut a bit of the lid away for it to fit.

Cut the nylon spacers in half longways, the best way you can... (this was a bear, I used a clamp and my jigsaw) I needed to combine two lengths of spacers to span the width of the guitar.

Superglue the nylon to the end of the neck, and to the base of the tin (for the bridge)

Drill holes in the tin for the strings (next to the audio jack), and one in the lid for the piezo sensor.

Finally, mount the strap buttons on the guitar. I mounted one to the back of the neck towards the headstock, and one to the back of the tin (this one required a michine screw and nut instead of the traditional wood screw)

Step 4: Wired and strung out...

Picture of Wired and strung out...
Projects 064.jpg
At last, it's time to see what this thing can do!

Wire the piezo sensor to the audio jack. Be sure to test it before securing it permanently...

Once the piezo is wired up, use some hot glue to secure it to the lid of the tin (just over the hole you drilled).

Finally, run the strings through the holes in the tin and run them to their respective tuning pegs.

Step 5: Tune it up, plug it in, and ROCK OUT!!!

Picture of Tune it up, plug it in, and ROCK OUT!!!
Projects 068.jpg
That's it! Rock out with your curiously small guitar!

There were some extra features I wanted to do, but didn't have time to get around to. Obviously, some frets would make for an easier playing guitar. Another thing that might help would be the bracket found on the headstocks of most guitars that hold the strings flat against the nut. I found that the strings would at times try to slide up the tuning peg to the point where they were no longer touching the nut. I plan on attempting to add these to my own Altoids guitar when I get around to making it. If successful, I'll be sure to post an update.

Thanks for checking this out, and whatever you do, be sure to have some fun with it!
1-40 of 68Next »
alcurb1 year ago

Video or sound file?

Its the piezzo a buzzer or a magnetic switch?
YoChuck (author)  HADJISTYLLIS6 years ago
You can get the piezzo element out of a buzzer. I lucked out and found this one in a battery-powered window alarm at the dolar store (piezzo, micro switch, and three 1.5v button cells for a buck!!!) Just take the outer casing apart (very gingerly), and the flat piezzo element will be inside. Try to salvage the wires that are already soldered onto the piezzo, as it's much easier to just solder extensions to those rather than try to solder new wires onto the piezzo itself. Also pay close attention to the polarity. Best of luck to you!
JtMS YoChuck3 years ago
if you are feeling fancy you can actually make your own piezo out of baking soda and cream of tartar powder... http://createdigitalmusic.com/2011/08/kitchen-contact-mic-chemistry-make-a-mic-from-baking-soda-cream-of-tartar/
I followed your advice and got a window alarm from the
dollar store and got one nice lookin' piezo!! 
evilmadcow4 years ago
I looked at a video on this and decided that i want it to sound like an actual guitar,
so how do you remove the effect that makes it sound like you are hitting tuning forks?
rownhunt5 years ago
Im working on one right now ive got the paint scraped of the top
and then i polished it with a buffing wheel and got a nice piece of birch which i stained to a chocholate brown colour..
But when i get my piezo does it have to be a 1/4" jack
can it be a smaller one for some computer speakers
or ipod headphones????
YoChuck (author)  rownhunt5 years ago
Yeah, I'm sure it'd be fine to wire whatever size jack you want to it.  Best of luck, and I'm happy you found one of those dollar store piezzos!
Muchkoolz5 years ago

In this picture here, you have two wires, a green one and a white one. I'm guessing the green one goes to the audio jack, but where does the green wire go and connect with?...

both wires go to the audio jack
Glockenator5 years ago
dark chocolate covered cinnamon?  i never knew such a strange flavour existed
reptar96 years ago
i wired the connections but i keep getting feedback, is it because i didnt sauder them together? or do i need a footpedal to just take away the feedback?
YoChuck (author)  reptar96 years ago
Are you getting feedback or a humming noise? The piezo sensor acts as a SUPER sensitive mic, so you should start at zero and adjust the volume from there if it's feedback. Humming is a bit more tricky, and I'm not sure of the best way to get rid of that. Perhaps soldering the connections would remedy your problem. I'd say just check your connections and make sure there's not a short anywhere. Best of luck!
1up YoChuck5 years ago
Humming is sometimes caused by a "ground loop". This is where there is more than one connection to ground. This acts an antenna to pick up interference.
Maybe something is shorting on the case and causing this?
Zem5 years ago
Which part of the piezo element is which?
 
lilbrewdog6 years ago
um...what did you spend making this guitar?
wangzo6 years ago
Nice design, probably the clearest instructable I've seen yet. Gonna make it soon
dreath776 years ago
so are ;they like those cigarbox guitars but made with an altoids can instead, its seems like it is and that is awesome
although i do have one questionss, wheres the frets, i play guitar and i know some guitars have frets. so is this that kind of guitar that doesnt
it's not a real guitar
zrune186 years ago
LMAO
D4VOBRO6 years ago
AWESOME AS!!!! Cool as... I read somewhere you can plug them into your mac and through garage band you can fiddle around with them. Do they sound remotely close to an electric guitar? Could you use a 3.5 audio amp with them? What would that sound like? Instructable perhaps... my calling... Great instructable
>>-----(===) this is my guitar..... all most as small as yours
did you use th first three strings of the guitar? or every other one?
YoChuck (author)  Funkmasterlogan6 years ago
I think I used the first three, but you can use any combination of them you want to. It's crazy sounding to begin with, so have at it! Best of luck!
how long is the main piece of wood? i bought some at Lowe's but i dont know how long its supposed to be, they didnt have precut i had to get it long
YoChuck (author)  Funkmasterlogan6 years ago
I can't remember how long it was exactly. I think 12-16 inches is probably a good length...
can i get ay ptzo from radio shack? or does it has to be a certain type.
YoChuck (author)  Funkmasterlogan6 years ago
Yes. Radio Shack sells piezo buzzers for electronic alarms, that work perfectly. Just pick one of those up and carefully dismantle it to get the piezo element out. You can even leave the wire leads soldered onto it (makes life MUCH easier!). Best of luck!
slowsam6 years ago
what would i use to make the frets???
YoChuck (author)  slowsam6 years ago
I considered several items to use, but unfortunately couldn't do any because of time. Some things to try to glue on the board would be toothpicks, straightened paperclips, or small finishing nails. I'm not sure if you could find them, but if you're looking to go the authentic route, you could try and find some real frets, actually cut slots, and install them. Best of luck with whatever you try!
lokisox YoChuck6 years ago
try using the copper wire core (solid) from antenna cable from a cb radio
YoChuck (author)  chi chi chippy6 years ago
That would work just fine if you want to use an in-line instead of the panel mount jack. As long as you wire everything up to the piezo correctly, you're good to go! Also, that link is to a 1/8" jack. That will work fine, but keep in mind that most guitar/music equipment is set up for 1/4". Best of luck, and let me know if I can be of any more help!
i went to radio shack and i got one of the cheapest 1/4 mono jack they have and i got it says that it is a phone jack can it still work? also on the peizo buzzer can i use this one or the other one?

this one
http://www.radioshack.com/product/index.jsp?productId=2062399
or
this one
http://www.radioshack.com/product/index.jsp?productId=2062397
YoChuck (author)  Jr Hacking kid6 years ago
I imagine the jack should work just fine, as long as it's a 1/4 inch mono... Both of the piezos should do ok. It looks like the first one is just rated for a bit higher voltage and current than the second one. Best of luck to you, and let us know how it turns out!
mkay! =)
emdarcher6 years ago
this looks like it will be fun to make. I'll try to make some frets so I can know what I'm playing though.
YoChuck (author)  emdarcher6 years ago
Yes, it's definitely 'slide necessary' without frets. I think there are a good number of fret calculators you can find online to properly space them out. Best of luck, and thanks for the comment!
gr1ffs6 years ago
The one I'm making right now is a full sized home made 24 fret neck. I'm sloting the neck and installing jumbo size nails with the tips and heads cut of for frets. the one I made before used finishing nails, but they give an uncomfortable feel and lead to hand injuries. also be sure to use a fret calculator.
1-40 of 68Next »