Baithive

The simple bait hive we describe here is designed to fit with a Honey Cow hive. The top bars are interchangeable, so moving your new bees to the Honey Cow is quick and easy. Like with fishing, you must be patient and wait. Before you know it, you’ll have happy bees ready to join your family.

For more detailed instructions, click here.
For more information about our other how-tos, visit our site www.velacreations.com

Step 1: The Box

- Start by marking one side of a 1X10 by 8 foot piece of lumber as follows, 24”, 33 1/2”, 40 1/2”, 51”, 61 1/2”, 72”. On the opposite side of the board, mark as follows: 7”, 16 1/2”, 40 1/2”, 51”, 61 1/2”, 72”. Draw lines between the marks, to create your cutting template. Using a circular saw, cut the board.
- On the cut edges of the side and bottoms boards, drill 3 holes along each side (6 total per board). Make the hole about 1/2” from the cut edge. For the top, drill 4 holes, 2 on each side on the factory (uncut) edge.
- On a flat surface, place the front and back boards with the 24” edge down, so that the boards are upside down. There should be a 8 1/2” - 8 3/4” space between the boards. Lay the bottom board in place on top of the front and back boards, and screw in place, carefully keeping the face boards square. Test the width of your bait hive by placing your top bars in between the face boards. They should fit easily, but not have any spaces between the top bars. Now, screw in each side board, carefully keeping the width of your box consistent.
- Drill out an entrance hole on the bottom of one of the sides. Round the edges of the hole a bit to give a nice, funnel - like opening.
- Paint around the opening of the hive with just a bit of white paint. Once this paint is dry, add some lines and decorations around the opening with your yellow highlighter. Bees can see fluorescent colors very well, and having a contrasting color around the entrance will make it easier for the swarm scouts to find the front door.
- Put your top bars in your hive. Attach the pieces of sheet metal on each side to prevent the top bars from moving or shifting.

Comments

[jlyvers743]

This is great information. I have read up on chasing down swarms and gathering for a new hive but that only works if your lucky enough to spot a swarm and then, free to tramp a path where they go. Not so easy for everyone. This, is amazing and any one can do it! Do you see any problem of just using this as a permanent hive?

[velacreations]

it is a bit small for a permanent hive, in my opinion. For a permanent hive, you could make the sides longer.

Better yet, build the hive that this was made for: http://www.instructables.com/id/Make-your-own-Honey-Cow-Top-Bar-Bee-Hive/

[jlyvers743]

Thank you. I followed your link and that was great also. I had read about the top bar hives and plan on using something like that. Awesome info! thank you.

[CapnChkn]

This will work a treat!  I use 5 frame nucleus hives for the swarm traps.

Using top bars, I have problems with the swarms building crazy comb.  If you don't define the point were the bees hang the comb, they'll hang it whatever way they like.  Then it will be a mess taking the bars out!  I spend some time laying a beeswax soaked cotton string along the center of the bars and fastening it with melted wax.

[velacreations]

if you look at our top bar hive, you can see how we make our top bars: http://www.instructables.com/id/Make-your-own-Honey-Cow-Top-Bar-Bee-Hive/

[brunovm]

It is illegal in some states to keep bees in non removable frames.
This is because of the need to inspect for disease.

[velacreations]

yeah, top bars are removable, but even in states where frames are required, there are usually a minimum amount of hives required.

join a local bee club to get the scoop in your area!

[jessyratfink]

This is a fantastic project!

[velacreations]

thank you!