Step 10: Clean Surface and Lay Down Acrylic

 First, remove the polished aluminum edge and acrylic. Clean the surface, and remove any grime from the steel panels. Peel off the down-facing film on the acrylic, then lay it on the table. Peel off the topside film- this moment is glorious! Suddenly the desk is brilliantly shiny. 

Screw down the edging, and you're finished!
I just finished mine. I had a little trouble with the legs, so I built a table frame to help secure the legs. I love how it came out!
Wow beautiful! This totally made my day! Nice work, and great pictures. Thanks much for sharing!
I think I would like to try this, but with a set of tarnished brass plates and a deeper mahogany stain.  I like the step by step of your 'ible, not too many boring details, and an overall assumption that if you are going to try this, you have some clue of what you are doing. Well written.
 Thanks! This would look great with a little victorian flair. You could even use brass screws or put laser cut gears and things underneath the acrylic. 
<p>Great project. I have been looking for a bistro style dinning table and this is perfect My dimensions will be different clearly, square-rectangular top and a matching narrow longer side table to go with it. I have worked with acrylic and good acrylic while more expensive is more resistant to scratching and for all that are asking I find that Plastic polish or scratch remover for car headlights and paint with a small polisher attached to some kind of drill for speed works perfect. Also creating designs or using pre bought patterns for etching the underside is an alternative. Very clear photos and instruction. good Job</p>
<p>How has the plexiglass been over the years.</p><p>Has writing on it caused it to scratch?</p>
Not bad. Not bad at all. Did you consider to get real glas instead of acrylic sheet? Should be scratch free for many years.<br />
Glass is a great suggestion- and it would look great over the steel panels.. Unfortunately the cost is prohibitive, and plexiglass is cheap, easy to work with, and lightweight. I'm also pleased with the durability so far- under normal use scratches should be a non-issue.&nbsp;
&nbsp;Yeah and you can always sand the plexiglass back to clear if you need to.
Can you sand plexiglass to clear? I've not had luck with that; is it just a matter of going to a high enough grit?<br><br>Actually, even sanding the plexiglass frosted would be a very interesting look with the checkerboard materials behind it.
<p>IF you search the net, you will find that even in the highest polished of materials, the bottom line is, the higher the grit, the finer the scratches become...in other words, you can start out with a scratched up, ugly looking piece of acrylic &amp; as you sand it with the different grits, getting finer grit with each change, eventually, you will have a gorgeous piece of acrylic....</p><p>Keep in mind though, &quot;polishing&quot; acrylic can be do 2 things:</p><p>1) it can take a loooooooooooong time to get it how you want it.</p><p>2) it can also be very hard, pain in the posterior, back breaking work..</p><p>Notice I said &quot;IT CAN BE...&quot; some time it is &amp; other times it is not....all depends on the quality of the work you put into it.</p>
<p>Also a good point to remember here is that it's always easier and faster to sand and/or polish 1cm x 1cm area, than 1m x 1m area. Also the bigger the area, the harder it gets to get it &quot;evenly&quot; sanded/polished.</p>
You can sand it to clear again, but it is a slow matter of working up from ~200 to somewhere above 10 000 depending on how clear you want it to be.<br><br>Oh and also you would be sanding with water on the surface (to clear the dust between the surface and the sandpaper) for most of the time.
<p>I can not say it enough...</p><p>ABSOLUTELY GORGEOUS!! :)</p>
Must be hell without a mousepad.<br />
<p>I have used an optical mouse for more than 12 years &amp; in that time, I have NEVER needed a mouse pad....</p><p>even some of the older mice with the tracking ball inside do not NEED a mouse pad....besides, If'n I ever need a mouse pad, I'd rather make my own....it's a lower cost that way.</p>
&nbsp;Optical mice work just fine! But It's my computer-free, distraction free workspace anyhow.&nbsp;
Ok, cool.&nbsp; Great looking project!<br />
<p>AWESOME!!</p><p>Absolutely GORGEOUS!</p><p>Tho it does not seem hard to do, I believe that what you have accomplished, has taken a lot of time, effort, and very exhausting...</p><p>BUT,</p><p>To see the finished product, makes it all worth it. : )</p><p>TY for sharing Sir....Absolutely GORGEOUS! : )</p>
Great project! I would have never thought of putting aluminum on a desk top. Bravo! I also built several desks which you can find on my website: krazy4projects.com. Thanks for sharing!
What was the wide tape used for?
No idea. I suppose I meant the painter's tape used when I bent the aluminum angle. <br> <br>The desk is still going strong by the way, 2.5 years later!
Great instructable. Just one quick question. Where did you buy the acrylic sheet and how much did it cost you?
I was able to find a sheet with the exact same dimensions listed above at Lowes for $47.75... on their site it's listed as &quot;DURAPLEX 30&quot; x 60&quot; Clear High Impact Acrylic&quot;, Item #: 11289, Model #: 1AG1775A.
How durable is the acrylic with use?
Nice, you could even write on it with dry erase markers if you wanted.
Did you cut in more then you did on the second picture? Or simply cut all the way through the top part of the angle, and bent the bottom to fit the work bench?<br />
Very nice! Simple, yet elegant at the same time. Well done!<br /> <br /> Matt<br />
Very nice job, and good instruction.<br /> <br /> L<br />
&nbsp;Thanks lemonie!
Thanks for the great instructions. How long did this take you and about how much did it cost?
&nbsp;It took about two days with plenty of downtime, a single trip to the hardware store, and $172.<br /> <br /> I have no doubt that this could have been done cheaper, but the price isn't so far off from a nice IKEA desk, and it's much sturdier. And hey, if I get tired of the design, I'm only a few screws away from changing the design.&nbsp;

About This Instructable




Bio: I like to explore.
More by zwild1:Birch and Aluminum Desk How to Navigate with a Map and Compass 
Add instructable to: