Step 13: Prepare the stereo plug

Cut two red wires and one black wire of about 6" length. The black wire should be connected ____. The red wires should go to the other two ______.
Where do the wires on the stereo plug go?
Where is the file for the mounting bracket? I can't find it :)
Ack. Long gone most likely. For a while Sparkfun.com was selling breakout boards for these sensors. I think they may still. It is approximately the same size as the file I had made and is pretty cheap.
Now explain to me how a mic analyses your breath for alcohol
The alcohol sensor does this.
that is a valid point
this is hilarious randy. every sunday is karaoke night at the bar across the street from my apartment, I'd love to use this as some kind of kill switch on the audio system, get those crazies off the mic faster...
It'd be great to interface this with a karaoke, or rock band mic! <br />
And then set up the mic at your local bar's karaoke night.
Can you do it with a cheapie breth tinig
Is there anywhere else you can get the alcohol sensor besides in Thailand I do not have that amount of time and i want to try and build this microphone
You can get it from SparkFun here: <a rel="nofollow" href="http://www.sparkfun.com/commerce/product_info.php?products_id=8880">http://www.sparkfun.com/commerce/product_info.php?products_id=8880</a><br/>
Not that I know of, but you can get the datasheet off the website and probably pull a part number off of there. Then you can just do a google search for it. I won't say its impossible, but it may be hard to track down. If you pay an extra $16 in shipping (or so) you can get it much sooner.
Cool. do you think you could explain how it works i'm thinking of building the sensor myself...even though i may epicly fail at it.
Did you have to "preheat" the alcohol gas sensor? I just received mine and it started off in the 1000 range. I've had it plugged in for about an hour or two now and it's down to the 800 range. The datasheet mentions a 24 hour preheat time. I think the normal range is supposed to be from 160 to 1024.
AWESOME! for some reason i couldn't figure out how to buy the <a rel="nofollow" href="http://www.alcometers.com">breathalyzer</a> from the link provided so i just bought the least expensive one from <a rel="nofollow" href="http://www.alcometers.com">http://www.alcometers.com</a><br/><br/>crossing my fingers!<br/>
wow, i like the idea a lot... ill have to be careful next time i take an interview :O make sure this isnt in there >:O i hope they dont catch me :P
uhh, jk btw i dont drink :)
youprobably do and dont know it
If someone's drunk enough to try singing into it, you'll know lol. No breathalyser needed.
just think how easily this could be 'hooked up' and Incorporated into a vehicle so the ignition would not start if the drivers pi$$ed! GENIOUS!!!
It's called an "ignition interlock device". In Arizona you have to get one installed in your car if you get pulled over and blow positive for alcohol, even if your BAC was under the legal limit.
They have those already.
i know somebody with one she says its a real pain and likes to break but she still likes it beter the losing her licence lol
Just so long as you realize that this won't be terribly accurate. It takes deep lung air to get an accurate reading of blood alcohol content, not the air that would go over the mic while talking. BUT it does sound like a fun toy at parties, but nothing more.
Indeed. Right now accuracy is my largest problem. However, I'd like to get it to a point where I have calibrated and tested it enough to be able to claim an approximate BAC level range.
Cool and LMAO!
how covert... *adds this to spy gizmos group* i give it a 4.5!
oh this is great!. further modification that might be fun would be to make a version where the recorder actually ONLY works above a certain BAC threshold. less useful, perhaps, but guaranteed to result in consistent silliness.
Might-ie cool. Can the Arduino fetch data from the logger, or is the logger itself write-only? (you can read the card, of course, externally.)
Wow! You finally did it! I've been waiting for this for a long time! 5*s and faved.
Dude, right off the bat you earned 5 stars for using the word 'truthiness' and second, this is a brilliant idea! I see big karaoke applications for this device.
Excellent Randy!<br/>This would be quite the project to take to school....<br/>:D<br/><br/><h2>&quot;TRUTHINESS&quot;</h2>Hooray for Colbert!<br/>
hehe, you said truthiness... Nice! Very cool tut!
Awesome job Randy! What's the output from the sensor, analog? I like the laser-cut circuit templates. Did you have any problems with them, such as burning the plastic w/ your soldering iron?
How did you find this? I didn't publish it yet :) The sensor is a really basic and relatively stable analog sensor. The soldering worked alright. The acrylic doesn't melt too easily and the connections were made quickly and slightly over the surface of the plastic, so it wasn't too large of a problem.
I'd love to say that I have 1337 skillz, but the truth is that I went to your memeber page, and it was there.
awesome! a new trick for undercover cops maybe....

About This Instructable


94 favorites

Bio: My name is Randy and I run the Instructables Design Studio. I'm also the author of the books 'Simple Bots,' and '62 Projects to ... More »
More by randofo: How to Change a Lock Bedfellow Robot Bed Easy Science Fair Project
Add instructable to: