Instructables

Build a Dog Cot for around $10

Picture of Build a Dog Cot for around $10
Build an effective, durable cot for your dog for around $10
 
Remove these adsRemove these ads by Signing Up

Step 1: Materials and Supplies

Picture of Materials and Supplies
IMG_0020.JPG
IMG_0021.JPG
· PVC pipe 1-inch (inside diameter determines the size) schedule 40 (thick wall). Can be purchased at Home Depot for about $2.48 for a 10-foot stick.

· Three way corner pieces (1 inch) item # F100W3W. Can be purchased at C & S Plastics 1550 5th. Street SW, Winter Haven, Florida 33880. Phone number 863-299-6639. Cost about .99 cents each if purchasing 240 count. This is a furniture grade specialty item that cannot be found at many places.

· Open weave plastic mesh marine upholstery fabric (similar to Phifertex) is the best choice to use. Awning fabric (similar to Sunbrella) can also be used, but it is not as easy to disinfect or dry. If only doing a few beds ask your local boating upholstery shops for scrap pieces. If needing fabric in bulk search the Internet for best prices.

· Buildex Teks Lath Screws #8 X 1/2" can be purchased at Home Depot for about $5.49 a box with 260 count. If needing screws in bulk contact Fastenal located at 295 Lewis Street, Fort Walton Beach, Florida or call at 850-302-0285 can be purchased for about $1.53 per 100 count. Ask for part number 32142.

- Cordless drill with variable clutch settings

- Screwdriver Bit

- Screwdriver Magnetizer (optional but very helpful if doing this alone)

- Rubber mallet
 
- Ratchet type PVC cutters

- Safety Glasses

- Tailor's chalk for marking fabric

- Fine Tip Sharpie for marking PVC

- Heavy Duty Scissors

- Stiff ruler

 
smendez72 months ago
I stumbled upon this site and thought "what an awesome project". I want my dogs to be comfortable but I hate smelly dog beds. I made 2 of them. I used 11/2 pvc pipes cause my dogs are heavier. I had to special order the corner connectors. I got real lucky and found the mesh fabric for .25 a foot. Both beds were made for under 50$. My dogs love their new beds and I love not having to wash any more smelly beds.
mbracero3 months ago

Hi, what fabric did you use to make the pockets for get into the pvc? Did you make it with a domestic sewing machine?

Thanks.

Marilia

trevormates8 months ago
Very nice.

You can get the 3-Way Fittings cheaply and in a whole mess of sizes from formufit.com. You don't need to buy a 240 count of them either! :)

I also recommend their furniture grade pvc pipe, as a previous poster stated, as it won't degrade outdoors.

Great Ible!
nmarshall611 months ago
Great idea, but defiantly not around $10. I could see around that price if I got scraps of fabric for free from a place, but I bought "duck" fabric.
13, 5:36 PM.jpg13, 5:36 PM.jpg
phizz506771 year ago
I made a version of this this weekend. I made it large, really large, so it would fit snugly in the outdoor kennel. Final size of mine is 5' x 3' and 12" legs. I made it tall because I know he will get his toys under it and stand there and bark at them if he can't get to them. :) I used "duck" fabric which I am certain will rip out eventually. I had to order my 3 way corners off ebay, found the duck fabric at Walmart. Your instructions were awesome and easy to follow and I really appreciate finding this!! Thanks!
Sturnl1 year ago
Nice job, i am looking for someting like this but then to take on a camping trip so mabey one without the legs!
vhosey1 year ago
What breed of dog is that in your picture? He/she is gorgeous.
And thanks! This is exactly what Ive been looking for.
cwyorkiex31 year ago
Thank you for sharing!Alot cheaper then in the store.
Lique2 years ago
Thanks for the tute. I found the 3way corner piece @ Lowes. I also found the open weave vinly @ Hancock Fabrics and it was $19.99 but I used a 40% off coupon to buy a yard.
Harborseal2 years ago
Also, another way to make a corner which is available where you bought the pipe and might be cheaper in small quantities is to use a T and a 90 degree elbow. The middle opening of the T points down to connect to the leg. A short segment (2.5 - 3") of the PVC pipe connects the T to the elbow and the elbow connects to the short side. The disadvantage of this is that pressure directly on the short side pipe can flip the bed. A T piece with leg reaching to the floor can be added in the middle of the short side to prevent this. That can make the 2 short sides uneven though. For my dogs (125 - 180 lb skinny Newfoundlands) I'd need 1 1/4 or 1 1/2" pipe. :)
Harborseal2 years ago
The lettering comes off with acetone easily, or rubbing alcohol with more effort.
dstellhorn3 years ago
Great article--thanks! I customized the size a bit to fit in one of the extra-large ASPCA dog crates, and the dog loves it! Just a note for anyone thinking about changes to the sizes listed--mine is 40" in its longest dimension, and the PVC flexes quite a bit under a 70 lb bulldog mix. If you're considering anything much larger, or for a heavier dog, you may need more rigidity in the frame.
My lab only eats beds/blankets in her crate so I used your great tutorial to make a crate one with a few EZ changes. Since she cant access the legs or the bottom once its in the crate this version is more forgiving for a rookie. Basically its a topper sitting on a folded blanket inside her crate--she luvs it!
*3/4 PVC cut to fit inside her crate (used the plastic tray from her crate as a guide)
*3/4 x 3/4 x 1/2" PVC Elbows for the corners (all basic stock @ Home Depot-under $2 each sold individually).
FYI: The 1/2" is threaded, the 3/4" sides are not--i did not find elbows with all smooth 3/4" sides
*1/2" threaded male risers (black cut-to-length PVC around 6" long in the Sprinkler/Irrigation Aisle-also cheap). You can adjust leg length individually by screwing in the riser as needed to level--just cut to fit. I wanted it short/more head room, so cut them 2" long--this gives you 1" high leg.
(You could also look for 1/2" white PVC male connectors + cut PVC pipe for legs.)
I folded her blanket smaller than the cot size then laid cot over it--its more padded & less stress on the cot fabric pulling on the screws since its not bearing all her weight. I removed the plastic tray that came with the crate.
I used black striped Sunbrella fabric from Jo-Annes Fabric store & cut the scraps into ribbons, then hot glued them onto the legs like a tube to cover up the white 1/2" PVC (remember she can't access the legs)--black legs blend into the black crate. Hope this helps :o)
marybarrow3 years ago
We made one of these types of beds for a dog that was incontinent but we used a mesh fabric. Instead of using screws, we made pockets that the pvc pipe slid into on all sides. Yours is a wonderful instruction.
jdege4 years ago
A Google search on "furniture PVC fittings" will return a number of sources for those three-way fittings. You might want to think about using furniture grade PVC pipe, as well. The plumbing grade PVC pipe degrades and gets brittle in sunlight, and has all that ugly lettering printed on it.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!