Instructables

Build your own Surfboard!

FeaturedContest Winner
Picture of Build your own Surfboard!
A dear friend of mine has a 1971 VW Westfalia Camper Bus he restored and wanted to mount a surfboard on the roof. Ultimately he wanted to cut the board and use it as a panel mount, so we looked for a cheap surfboard with little success. The cheapest one we found was well over 100 bucks, and a) to never use it as a surfboard and b) cut it up at a later date; cost was not justified.

So, I made him one!

The goal was simple; find cheap materials and make a cost effective surfboard. It more than likely will never be used as an actual surfboard, but it very well can be. Well, more like a flotation device I suppose. After all, wood does float right?!

Materials:
You will need the following:

-Five 2x4 planks (I would recommend more, but that is what I used)
-Wooden wedges
-Circular Saw
-Jig Saw
-Butcher Paper
-Duct Tape
-60, 120, 200, 400, 1000, and 1200 grit sand paper
-Wood Stain (I used gel stain)
-Outdoor Clear Wood/Deck Sealer
-Wood glue
-Wood filler
-Clamps
-Planer (Electric strongly recommended)
-Work Gloves
-Face Mask
-Eye Protection
-Broom
-Work Bench or saw horse

I already had most of the items listed. I used the cheapest 2x4 I could find and I bought the small quart sized cans for the stains. The wood glue was the large gallon, and the wood filler was the larger of the three cans available at Home Depot. Total expense was between $40.00 -$50.00.

I used a lot of advice from this guy, Abe Toke
He has a neat video series I suggest watching before you start! The main difference is he (and most sources I found on the internet) use foam boards.

As a side note, I am going to include a couple of steps I learned from my mistakes throughout this instructable.
 
Remove these adsRemove these ads by Signing Up
nickerkul11 months ago
what kind of wood did you use and is it not nessey to To cut the chambers to lighten it up? thx
Is the board easy/hard to ride?
joechacon98 (author)  StudlyPalmtree1 year ago
We have yet to put it in the water! And even worse, I have yet to put the fin on!!!
oud252 years ago
where is your fin?
joechacon98 (author)  oud252 years ago
I did not add a fin (yet). We wanted to wait so we can measure how high the board would sit on his bus. We needed to make sure the bus, board and fin cleared his garage door.
Once I add the fin I will update

(That's also the last note on the last page) ;)
reeseecup2 years ago
dude thats cool
joechacon98 (author)  reeseecup2 years ago
Thank you! It was fun making it
thats not my instructable -reeseecup
joechacon98 (author)  reeseecup2 years ago
Haha, I was saying thanks for the comment, then just stated I enjoyed making the board. I see how it is misleading!
sorry
oh i didnt know u r the author
I am looking forward incredibly to making this, but first a have a few questions.

Does this actually surf? i want to use the one I'm making as an actual surfboard.
Where do i put the fin at the back? Is there any video instructing me on the best place to put it?
Would I be better off to use dowels as well as wood glue or is there any need?

If you could get back to me as soon as possible that would be great! By the way this is an incredibly good project!
joechacon98 (author)  genericusername52 years ago
I have not taken it out surfing yet. Judging by the opinions by others who actually surf it can.
BUT if you are making a surfboard, I would recommend forking out some money and buying balsa wood. It is really light weight, durable, and seems to be the wood of choice for surfboards!

The fin, I have not placed it yet. And again, we are using it for decorative purposes. I did find a couple of links that go into great detail on fin placement!

http://www.tactics.com/info/guide-to-surfboard-fins

http://www.surfscience.com/topics/surfboard-fins/placement/surfboard-fin-placement

Here is a video that will show you how to place a fin
http://www.ehow.com/video_4411389_mark-fin-placement-surfboard.html

Dowels, I did not use. Most boards I saw did not use them, but I suppose it wouldn't hurt. Thing to keep in mind is balance. You wouldn't want 8 dowels on the left side and only 2 on the right.

Oh and your body weight will determine the size of the board you want to make!
Here is a site that has a nice chart:

http://www.islesurfboards.com/surfboard-size-and-weight-chart.aspx


Be sure to post an instructable!! I would love to see how you made it and how it did!! Good luck!!
Thanks so much for getting back to me so quickly and with so much useful information! I'm planning to make it around Easter when i have time off from collage. I'll post the link on here and let you know how it works in the water! Love this instructable thanks for making it!
joechacon98 (author)  genericusername52 years ago
No problem, we are all here to help each other out. Best of luck when you go on this endeavor. I look forward to seeing it!
duncan_a2 years ago
Why is this entered in the FURNITURE Competirion???
joechacon98 (author)  duncan_a2 years ago
Why wouldn't it be?!

Furniture [fur-ni-cher] n. :
1. The movable, generally functional, articles that equip a room, house, etc.
2. Fittings, apparatus, or necessary accessories for something.
3. Equipment for streets and other public areas, as lighting standards, signs, benches, or litter bins.

Considering it is an accessory to the bus and will provide a panel mount (and lighting) at a later date, in this case I think it is ok to say it is furniture ;)

Thank you for your input!!
i agree, i haven't made a surfboard, but i do have a SUP (stand up paddleboard) on my wall, in the off season its a piece of "furniture". so a surfboard can also be furniture.
joechacon98 (author)  cnmaine2 years ago
Thank you for the support! I am glad I am not crazy to consider a board a piece of furniture!
I have seen boards hanging up, they look very nice!
GainEnergy2 years ago
No matter what, the board itself looks very beautiful! It may be too beautiful to put in water! ;)
joechacon98 (author)  GainEnergy2 years ago
Thank you for the kind words!!!!
LifeWarrior2 years ago
Very cool use of stains to make a design!
joechacon98 (author)  LifeWarrior2 years ago
Thanks! Maybe next time I will use different types of boards to get different colors.
I've seen people do tribals with paints, never thought of doing it with stains. This would be cool as well on a hardwood floor.
joechacon98 (author)  LifeWarrior2 years ago
I bet that would look nice! Again, make sure you use gel stains for designs. Oil based stains will seep under the taped off areas; gel stains will give you those sharp edges!
BobAJobRob2 years ago
Don't get too excited about it holding your weight in a pool. Usually surfboards will only support a person standing up if they are moving enough to produce lift.
For comparison, I ride a 9ft hollow wood longboard - it's the most buoyant board I or my mates have, but there's no way I could stand on it if it was stationary!
Nice project though - should look good on the van. Have a look here for inspiration for the next one!
http://www.grainsurf.com/forum/index.php
joechacon98 (author)  BobAJobRob2 years ago
Great site! And thanks for the info. At least now I won't be too disappointed if the board doesn't hold me up!
b2j22 years ago
From the weight, the volume is under one cubic foot. which would support about 60 pounds in water. However, a good wave might be surfed. Or, if you are in the desert, you could surf a dune!
joechacon98 (author)  b2j22 years ago
I hear White Sands in New Mexico is the closest thing to snow in the desert. Good place to try!
hirod32 years ago
Great instructible! I was the lucky recipient of this board, and I can honestly say it is gorgeous in person!!!! Thanks a million!!!!
joechacon98 (author)  hirod32 years ago
Thanks mang! I am glad it did not turn out looking like dog dukie!
We still need to add the fin! And panel!!!!
We can put the fin on, but there's no way in hell I'm letting you cut a hole in the middle of it!!
bertus52x112 years ago
Very nice piece of craftmanship!
joechacon98 (author)  bertus52x112 years ago
Thank you very much!
rimar20002 years ago
Beautiful!
joechacon98 (author)  rimar20002 years ago
Thank you!
zim0142 years ago
How does it ride?
joechacon98 (author)  zim0142 years ago
On the roof, pretty darn well!! Haha it is difficult to take it surfing in the middle of the desert! Soon I would like to drop it in a pool and see if it at least holds up a full grown man. I will post results!
Sovereignty2 years ago
That's awesome.

How much did the finished board weigh?
joechacon98 (author)  Sovereignty2 years ago
Thanks! My friend just checked, 30 lbs.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!