Instructables
This instructable will show you how to re-use an old cork and a USB to create an awesome looking flash drive.
I have entered this in the Green science fair contest because it is re-using two old objects to make a modern chic piece of hardware.
2nd Instructable
DONT FORGET TO VOTE!!
 
Remove these adsRemove these ads by Signing Up

Step 1: You will need...

Picture of You will need...
For this Instructable you need:
A Cork - one made of real cork not plastic, i chose a champagne cork as it was
the largest one and able to hold my USB
A USB - doesn't matter what capacity, try to get the smallest one size wise as it
needs to fit in the cork.
A Knife - Anything sharp with a smallish blade will do nicely, i have chosen an
Exacto knife.
Tape - I have used white electrical tape.

Step 2: Stripping the USB

Now you need to strip away any excess plastic to make the USB as small a possible to fit inside your cork.
Most USB casing is in two halves which clip together around the USB
all you need to do is find a seam along one side and pry it open withe either your fingers or your sharp blade, the two halves should pop right off.
Now with the bare USB you need to size it up with your cork to make sure it is wide and deep enough.

Step 3: Cutting the hole...

Before you start cutting it is a good idea to draw a line around the bottom of the usb on the cork, this is so you have a general idea of how thick and how wide to make the hole (look at pics)
Now begin the cutting, cork is actually allot tougher than it looks so i recommend carving out a small groove on the top inside the line you drew and then just shredding at the cork and emptying out the shavings every so often ( very careful with your fingers here , high risk of severing)
Also be careful not to cut the sides too much otherwise it will all fall apart.
when cutting every so often shove the usb in the hole to see if you've cut enough out.
1-40 of 41Next »
Saitu5 months ago

You don't experience any heating problems? Cool. Imma give this a try, then!

Make the cork easier to cut by pouring boiling water over it before starting your project.
PSPerson4 years ago
Reminds me of this.....
i want that
yskroc2 years ago
Don't think this is "cool", as the USB will get hot and no no space to dissipate the heat !!!! lol.....
Gage9874 years ago
you could pop the cork into a bottle and hide the drive.
I understand that the reason wine bottles are now corked with that plastic stuff is because real cork has been violently over-harvested over the years and the quality has deteriorated quite a bit. That's why if you don't have a good bottle opener, the cork might break and fall into the bottle. Kind of sad.
sharlston5 years ago
put a weight in the bottom of the cork so the top usb floats in water then it wont get wet
raykholo5 years ago
kind of looks like ur computer is drinking KIND OF
Pags6 years ago
This is a great design because it covers 2 other usb slots besides the one it's using.
luke Pags5 years ago
umm ... thats a firewire port and a usb... but its still cool !
=SMART= (author)  Pags6 years ago
Hell yea !
whitish6 years ago
i had this idea! i guess i waited too long. (curse me and my lack of corked bottle beverages drinking)
KenGriffin6 years ago
Awesome! I think I will do this but with a fairly large cork so I can have a cap to it as well. - Ken
puffyfluff6 years ago
I've never heard of this before. It's really neat. I'm glad I've got many many usb drives to do this too-there are so many instructables! This is one of the best though!!
=SMART= (author)  puffyfluff6 years ago
Thanks !!
go alcohol
=SMART= (author)  AnarchistAsian6 years ago
lol
Labot20016 years ago
Unique idea! I might do this... I'm looking for a cool mod for my thumb drive that's lost its shell. 3.5/5 Stars!
Once I get my hands on a champagne cork big enough, I'm gonna make this. What about a cork lid as well? :D
=SMART= (author)  DuctTapeRules!6 years ago
Cool, i was going to make a lid but i diddnt have another cork :P
fedelosa6 years ago
Haha! That's a cool mod!!!
I used a lego brick Thanks
maccrew6 years ago
A little large, but still cool.
Keith-Kid6 years ago
cool idea! +1!
realy nice job! one thing is that you may want to make a cap for it out of another cork, just to keep it a bit safer and stop stuff messing round with the actual connection
=SMART= (author)  drummonkey926 years ago
thanks, good idea i think ill do that :D
=SMART= (author) 6 years ago

WAHOOO 1000 VIEWS

This is neat but if it's used for heavy writing won't it overheat and maybe set the cork alight?
=SMART= (author)  thefunktopus6 years ago
yea it gets quite hot after 10-15 mins plugged in
FireSnake6 years ago
I love this idea! what makes it great is THAT it's big, (Thumb Drives like to get lost) AND that it floats! If i might offer you some fabrication advise and you'd like to hear it, PM me. I hope you receive recognition in the Green science fair!
Try using a drill next time. It would be safer and easier. Also, it is "severing" not "decapitation". Decapitation refers to the head, not digits.
=SMART= (author)  ColbyCirca896 years ago
ok lol i changed it
=SMART= (author) 6 years ago

VOTE!! :D

neat idea....
=SMART= (author) 6 years ago
UPDATE- i took it to school today and everyone thought it was great!, one person even offered to buy it off me !
I gotta admit, this is really awesome. I never knew an X-acto knife could do this. But this is pretty awesome, I might do this. +1 rating. +1 vote.
=SMART= (author)  GorillazMiko6 years ago
Thanks Man!!!
LinuxH4x0r6 years ago
Nice! A little big, but good idea.
=SMART= (author)  LinuxH4x0r6 years ago
yep its quite big! lol thanks
1-40 of 41Next »