Instructables

So you think your coffee is strong? Wait until you have tried your coffee cup!

"A Honeycomb core is an array of hollow columns made of sheet material which is used to separate the two facings of a sandwich structure".

So why not make one of Coffee Cups and enter the Coffee Cup Challenge?

This I'ble will show you how to make a honeycomb panel as a building block for your future projects.  If you like it, don't forget to vote for me!

Note
Where I live, paper cups are somewhat rare, so I have merely made a beam and tested it. 
My project has ended by testing this beam. If you want to take it to the next level or if you have an awesome idea, feel free to use this information and even post it in the Coffee Cup Challenge as well (some credits would be nice though).
 
Remove these adsRemove these ads by Signing Up

Step 1: What do you need?

Picture of What do you need?


It's a great misconception that you need fancy materials to fabricate composite materials. Nature is full of extraordinary examples.  

You will need:
* 45 coffee cups
* two triplex strips of 90 x 20 cm (thickness 2 mm).
* Glue.

The dimension of the strip was more or less determined by the fact that I could only get hold of 45 cups (3 rows of 15 cups).
 


Step 2: How it's made.

Picture of How it's made.
CSC_1145.JPG

1. Apply glue to one side of the first strip (preferably with a brush)
2. Place the cups in an alternating pattern.
3. Apply glue to the second strip and place it on top of the cup.
4. Add lots of weight.


1-40 of 58Next »
IOPort513 years ago
this is great, good thinking! I think these would not be as thermally resistant or as strong as SIP's but a lot more cost effective for a lot of purposes. I am thinking about farm structures, chicken houses, rabbit hutches, small barns. Not taking away from the Styrofoam cup concept but free association brings me to the next obvious choice being aluminum drink cans. You could set a house on one of those!
I am looking forward to your next project, whatever it may be.
bertus52x11 (author)  IOPort513 years ago
Thanks!
In the discussions on the main page, you can find a discussion about using aluminium cans (Coke).
Biggsy3 years ago
You know.. i think i'm going to set this as a challenge for my Scouts! hehehe
bertus52x11 (author)  Biggsy3 years ago
Pay very much attention to the glue bond between the cups and the skin. This is the most important aspect of the strength!

Show us the results when you're done!
I shall do :)
Kryptonite4 years ago
You heard about that group that made a bridge span 5 metres, that held 200kg and was made of paddle pop sticks and glue?
bertus52x11 (author)  Kryptonite4 years ago
No. Would be nice to see.
It was on tv a few years back. Can't find a link, goddamn it!
there are annual competitions all over the country, and the world, for this. google popsicle bridge competition and you'll find all you want. the great ones are where, rather than unlimited sticks, the contest is to make the strongest bridge with a small number.
Some of the results are amazing.
I've looked every where and haven't been ableto find it.
Link?
tulekah4 years ago
this is a TORSION BOX, way way cool. i'm thinking of two sheets of glass bound by epoxied glasses!
bertus52x11 (author)  tulekah4 years ago
Just do it! Would be cool, don't forget to post it.
(alternatively, use Gorilla Glue, enter the Gorilla Glue competition and win some of the prizes...)
yoshhash4 years ago
 If you filled the voids (outside the cups, not inside) with expanding foam, or some other adhesive, light, form-filling material, you would eliminate the "weak points", which is the only thing wrong with this very BRILLIANT idea of yours.  Not only that, but it would then be an insulating material. 
expanding foam expands and will dent the cup walls. this is like the old "stand on a pepsi can" trick.
bertus52x11 (author)  yoshhash4 years ago
That's just one step away from getting rid of the cups all along and to go for a foam core!
However, I think your suggestion could work and your point is that there is room for improvement (as stated by myself in step 4 of this I'ble).
Only thing is, currently I don't have the time nor the resources to take it that step further (hope that someone else will. you?). That's why I made the remarks in step 1 about the contest. I'll be happy to contribute.

Oh yeah, air is one of the best insulators around!
cogni4 years ago
What is a "triplex strip"? 

Could one just use corrugated cardboard? 
If so, coroplast would also work (corrugated extrusions of plastic) but it is more expensive.  $10 for an 8' x 4' sheet here, from a sign shop.
tulekah cogni4 years ago
dumpster dive cardboard boxes. cut into 4" strips (cut across corrugation) and roll (pop-can) into tubes, glue between face cardboard strips (the corrugation lines should run parallel to the longest dimension.
you can make the faces stronger by doubling the face, or by cutting the faces on the bias with the corrugation at right angles to each other.
bertus52x11 (author)  cogni4 years ago
Triplex is just plywood (so I have learned in the discussion at the intro of this I'ble).
I guess you could use cardboard, just as long it doesn't get wet (but then the same applies for the cups!). The skin of the sandwich panel must withstand tension and compression. So the cardboard may not be too thin.
Coroplast might work as well, but seems a bit expensive? (but will paper adhere to plastic?) If money is no problem, I would get rid of the coffee cups all together, but then that's not so much fun!
beehard444 years ago
why not put scrunched up paper as filling in the coffee cups to make them stronger? maybe slather the sides with concrete for building material? just suggesting
Stevie894 years ago
Coffee cups hard too find? lm a Canadian.. in my city, Saint John NB, we have like 25 Tims alone, 3 starbucks, 4 Java Moose.. coffee cups are EVERYWHERESSSSS :-S
zeeebus4 years ago
I was thinking the same thing about the walls.  Much like a SIP, but homemade and less styrine. 

I can imagine building a 8' tall frame using studs the same width as the height of the cup (If cup is a medium, it will be xx inches tall, therefore your stud should be a 2 X xx inches wide stud.). 

Put studs on 4' centers. (4' is probably too wide actually.  I think, you would have to place them just inside the width of the plywood so when you are actually attaching the panels to the framing of the house you can nest the panel into the framed wall bay and nail the existing frame to the panel frame.)

Temporarily screw a sheet of 4x8 OSB onto the frame and flip it over so the OSB (Plywood) is on the bottom of the frame. Lay the frame at a slanted angle (the laying angle of a drafting table, say). 

The angle would allow you to stack cups onto the entire field of the plywood between the studs with cups. 
Next, you would take a second sheet of OSB and, using a roller or air pressurized sprayer(not disposable aerosol type, but the kind used in finishing booths at furniture and body shops), coat the ply with laminate adhesive according to manufacturers instructions. 

Apply this sheet (when it is good and tacky and ready) to the frame.  Screw it permanently to the studs. Ideally (I'm making this up as I'm typing, so bear with me here) Ideally the contact of the cups onto the glued surface would be pretty uniform.  Maybe a stud that is just a hair narrower than the height of the cup would allow for the adequate uniform pressure to contact all the cups.  I guess you'd have to be careful not to crush them, though.

Next, you would flip the entire 4x8 coffee cup "sandwich" over so that the adhesive coated plywood is on the bottom. 
Remove the first sheet and coat appropriately.  Re-attach to frame, and VOILA!  You've just made your own Coffee Cup SIP! (Oh, (S)tructural (I)nsulated (P)anel)

The load is carried on the studs.  I think...By all means, use at your own risk... Any engineers out there should  probably put me in my place here.

I think the real SIPS have the studs a small distance from the edge of the ply, which allows them to nest with a second stud already attached to the bottom plate of the wall (the horizontal 2X___" that is already fixed to the floor of the structure)
Any thoughts?

Just a thought. 
Great Instructable!!
bertus52x11 (author)  zeeebus4 years ago
Looks like you have written an Instructable! Add pictures and post it, I would like to see it! ;-)
Darn.  I was afraid that was what was happening!!!

Thanks for the reply.  Guess this gives me the summer project I was wondering about.  We'll see.  I would really like somebody to tell me if this sort of thing would be dangerous at all.  I'm concerned about structural soundness primarily, and fire secondarily.  Anybody???

By the way...you should have definitely beat the coffee cake entry and winner.  I didn't read any of the comments on the thing because I didn't think it was all that great of an idea.  Now that I've looked at it, I'm wondering if the wax on the inside of the cup wouldn't enter into my reproductive system, or some other remarkably unfortunate place!!!

I'll start collecting cups and stuff for the SIP.
 Oh no, I can't find the vote button! Nice project anyway. I'll be sure to make my shelves with those.
bertus52x11 (author)  nutsandbolts_644 years ago
Thanks, and post an Instructable if you're done!
I believe voting is possible from May 10th on, but I'm not sure how it works (if you will see a button).
Kiteman4 years ago
This could make an interesting door or screen-wall, especially if you use transparent acrylic to sandwich the cups.

For a table-top, you would only need the top surface to be transparent.

Well done.
knektek Kiteman4 years ago
Yes, if you want to look like a poor man who can't afford a proper table. Instead he would have a table made out of coffee cups.
Kiteman knektek4 years ago
I guarantee that if you made a table like this, and sold it through an agent, you would get well over the price of a standard table.


And Ikea would buy the design and release a trendy Starbucks-y version for twice that amount...
 This is where it gets pointed out that the Ikea LACK furniture brand is based on hollow-core door engineering.  Both hollow-core doors and LACK furniture are made from a composite honeycomb material whose walls are usually thick card or thin wood.  

So, in other words, such an idea could only be called LACK-luster.
 actually it's just paper (not that I ripped a door apart; I just saw it on TV) that's the honeycomb material you're talking about, although if it was some composite it would be extremely strong.
knektek Kiteman4 years ago
it is now futile for me to emphasise the words 'coffee cups' ...
It may be cheap, it may seem tacky to you, but to others, it is a work of art, and a sense of taste, which apparently, you don't have.

WORD.
This is a world with opinions. Anyway I was talking about using USED CUPS for this. Not ones that have been drank from. Other than that this is a great project.
You didn't say USED CUPS once in all of those comments, so don't play that with me.

Well, i'm not playing anything with you. so...



WORD!
Word.
you underestimate art
1-40 of 58Next »