Instructables

Magnum Condom LED Music Light

Picture of Magnum Condom LED Music Light
Sound Activated Condom Lights. Must see the video ending :)

 
Remove these adsRemove these ads by Signing Up

Step 1: Supplies used,

Picture of Supplies used,
C:\Documents and Settings\Fishin4Daze\Desktop\DSC00138.JPG
2 Blue 5mm LED's 3.7 volt 2600mcd
2 5mm LED Holders
2 Condoms
Heat shrink wrap
Some thin gague wire. I used an old phone cord.

Clear Silicone
2 tops off a Gaterade bottle
Multimeter
Electrical Tape
Wire strippers

Step 2: Putting it together

Picture of Putting it together
Install the LED's into the holders, and attach the holders to the bottle tops.
(Note, the longer leg on the LED is positive, so hook your wires up accordingly.)
Add some thin wire to the LED's(I use an old phone cord), and attach the wires to your speaker wires. This will only work on amplified speakers, or speakers that plug into the wall.
1-40 of 64Next »
NoahArca5 years ago
Ha this is very creative! I'm really diggin the music you used too! Who is it by?
I dont want to break the news to you, but a friend made it for the guy, so you can't really get it.
DAMNNNN that sucks.
teeznutz6 years ago
compressed air is for wimps. why not use your mouth? come on, please? just this once?
MJTH teeznutz5 years ago
Lol
MJTH5 years ago
Maybe want to say Non Lubricated Condom?
That is sooo very err........ koooooooooooool!!!!!!!!!!!!!!
WildSavage6 years ago
well my LED burned..
it worked and i volume my speaker up, the LED actually started to turn into red and burned. :(

but for the whole things, it works though.
Wave thro the LED- let it FLOW~
did you add a resistor to the LED ?
-Aj- erral5 years ago
am guessing not :P or speaker level was too high
it's an led safey!!!
geoffcubed5 years ago
To avoid any damage you could use fast switching relays. WIth relays you could also run larger lights...
but relays cause access noise, and they are slow
=SMART=5 years ago
Hahahahahahahahahahah ROFL
how do i connect the wires to my speakers?? faved and 5*
sumguysr6 years ago
there are two problems with this implementation, first is that an LED is a diode and audio signals are ac, so the audio that reaches the speakers would be rectified and you would only hear the top or the bottom of the sound waves, the second is a diode represents a constantly changing series impedance which would destroy the impedance matching between the speakers and the source, resulting in bad sound at best and equipment damage at worse.
What if you hooked just the LED to the Speaked output. Left channel music right channel Lights? Still the second greatest thing to use a condom for
Yes, I've seen many of these LED instructables, all running on A/C, I wonder if you could use your d/c powered iPOD instead. Just cut the headphone cord and install the led. If you want to hear the sound too, you can get a speaker set for a little bit of nothing on eBlah and do the same thing. Heck...This calls for a new instructable! Seeing as I dont own a iPOD (fighting the man, or some such), I wouldn't mind someone stealing my idea. Maybe it's already been done?
sumguysr viacin5 years ago
viacin your missing the point. The power that the source uses doesn't matter, it's the electricity coming out of the headphone port that does. Analog audio is always AC. I would think an LED would be even worse on an iPod actually since iPods output much less power than most stereos and I think(but don't know) that a constantly changing impedance mismatch would be much more noticeable on a pair of high impedance headphones(16 to 32 ohm) versus lower impedance(4 or 8 ohm) speakers. geof, it would probably work to use an led on just one channel with no speaker but you would have to add a fairly heavy duty resistance as well since most audio sources don't like playing into shorts. Also I would put 2 LEDs in parallel but with reverse polarity, so that the audio source didn't see any rectification.
MJTH6 years ago
Im Glad You didnt use your mouth to blow that up.
viacin MJTH5 years ago
lol, I was wondering!
viacin5 years ago
Tesla would be proud.
vpsekharan6 years ago
The circuits and building instructions are very intersting.
jesus u can do alot with condoms
fkuk6 years ago
dont you have a better use of condoms?
static6 years ago
I'm wondering at what point during normal condom use, one pauses to think; Wouldn't it be far out if I did this with a condom?
themolok6 years ago
F*cking Awesome!
andrew1016 years ago
oh and a better way to tell positive and negitive on the led isnt wich lead is longer (because not all are) look really closly at it its round but one side (at the base) is flat the flat side is negitive.
zzag andrew1016 years ago
The way I remember: "Cathy is short, flat, and negative." I.e. Negative leg is determined by: The cathode is the short wire and/or the flat of the bulb. (If your mind is as bad as mine, it's yours free of charge.) .
fishin4daze (author)  andrew1016 years ago
Thanks for adding the info.
inertia186 years ago
can you please post the song here. Its fantastic. thanks nice instructable a plus for you dude.
pegassuss226 years ago
What is that song??? tnx
Macka6 years ago
lol, that looks awesome. Maybe now i'll have an excuse to buy condoms :D
Zujus6 years ago
Really cool, but still need more good quality photos to be perfect.;)
MrSootentai6 years ago
I love this video, and I actually want to do the project, but I'm still confused on the wiring. Can anyone draw a diagram or something for me?
gotclawz16 years ago
i really want to do this and i have the right speakers but im not sure what wire to hook it up to. note 1 wire goes to my comp, 1 goes to left speaker and 1 goes to the wall, so which one is it?
J_SCAP6 years ago
lol light up penises roflmao
itsME_lulu6 years ago
it's so cool but i'm lost...can u make it more specific on the info because i'm confused where to hook the wires to. please... thanks.
i dont see how that would work.....please explain? im not sure much power goes to the speakers......
Darthdoom6 years ago
Didn't work for me, work with any speaker?
1-40 of 64Next »