Instructables
Picture of Crystal Ring
IMG_4480.JPG
IMG_4477.JPG
IMG_4478.JPG
This project can also be done with super glue if you don’t have means to solder.

The third picture is as shown on my daughter's little hands.

 
Remove these adsRemove these ads by Signing Up

Step 1: Strip a coat hanger

Picture of Strip a coat hanger
IMG_4448.JPG
Use sand paper to remove any coating on a section of coat hanger. To help speed up the process I spun a piece in my drill press.

CAUTION! If you do it this make sure to hold the wire before you turn the drill on. Otherwise the section of wire will turn into a whip / weed wacker. Be careful and work within your experience.

Step 2: Make the ring

Picture of Make the ring
IMG_4454.JPG
IMG_4457.JPG
Hammer a section of wire flat. To do this you have to hit the wire squarely. It you hammer off center the wire will hook to the right or left.

Form a circle on a socket bit. Check it against the finger it’s made for for proper fit.

Cut the ring to size and file the ends square.

Step 3: Polish

Picture of Polish
IMG_4459.JPG
IMG_4460.JPG
A drill press is helpful but not necessary. Mount a socket through a bolt into your drill press. Place the ring over the socket.

Spin the socket round and use 400 grit sand paper on the ring. Move on to 2000 grit sand paper and then polishing compound. You can place some electrical tape on the free end of the socket to help keep the ring in place.

Step 4: Make the setting

Picture of Make the setting
IMG_4461.JPG
Use a paper clip to make the setting. Wrap the clip around a round shaft. I used an o-ring pick.

Cut a ring out and file the free ends so it closes with a nice fit.

Step 5: Solder or glue

Picture of Solder or glue
IMG_4467.JPG
IMG_4468.JPG
If you don't have means to solder use super glue. Otherwise:

Secure the ring in a clamp for soldering. Place the paper clip ring over the seam of the coat hanger ring. Orient the paper clip ring so the opening lays over metal.

Apply flux and drop in a small piece of solder. Use a torch to solder it together.

File off the excess from around the edges. Use 400 grit sander paper on a flat surface to sand down the solder on the setting.
rb700712 months ago
Absolutely Brilliant! :D
Belana1 year ago
genius
Think i'm going to have to try & make one of these. I'd imagine it wouldn't be too hard to zinc/silver plate it to stop it from rusting. I'll have to experiment & post my findings.
puddingpet2 years ago
I think I've seen coat hanger wire straight, uncoated at the hardware store before.
So adorable!
dolwiz2 years ago
I love this idea. My boyfriend could propose with this and I wouldn't love him less, probably more knowing the effort he would put into it..
mcshawnboy3 years ago
In step 3, if tape doesn't keep it in place you can get something used by lapidaries to mount stones for shaping called "Dop Wax" is about $10, but would likely last a lifetime. Here's pot to heat it easy & safe, reheat it to remove after polishing. : ) http://www.kingsleynorth.com/skshop/product.php?id=94265&catID=1125
nanosec123 years ago
I would monitor this carefully, especially with small children. Most coat hangers are made of a low grade steel, which will rust from the moisture on your skin. This can leave a reddish stain to the skin that is hard to wash off, but will eventually come clean.

Other than that, what a great project.
Mrballeng (author)  nanosec123 years ago
Don't worry I used a Tiffany Platinum hanger. Actually it's a regular coat hanger =).

Thanks for the advise, I'll keep an eye out.
You can coat the hanger using a clear coat polyurethane. It won't be perfect, since it will chip and you'll have to re-apply, but at least it will work for a while. You also might experiment with anodizing - you can get several different colors of anodization. Of course it increases the price slightly...

You can find instructables about anodiztion.
You can't anodise steel; the properties of rust make it impossible (well it is possible, but entirely pointless). With Aluminium or Titanium, you get a tightly locked layer of oxide. But with steel or iron, you just end up with flaky rust, exactly what you're trying to avoid.

The best solution would probably be a coat of paint or lacquer; or, better yet, use aluminium and anodize it :P

can you electroplate it?
Yes, of course you can.....You can use any of several methods to plate it with silver, gold, platinum etc. But, honestly, I believe that this was supposed to be an easy/inexpensive craft to do with/for children. Taking it to the electroplating level is a bit beyond the scope, but entirely possible.
i had no idea that one could solder steel ..

old dog + new trick !

psuddeth3 years ago
Whadaya coat it with to keep it from rusting?
Mrballeng (author)  psuddeth3 years ago
You can use clear nail polish. I have not noticed a problem with rust yet but then again I live in a desert.
BobCat3 years ago
I hope that you used lead-free solder. You should warn people against using leaded solder in the instructable, too.
tkjtkj BobCat3 years ago
good point , but i think people ought to know that under federal law, 'leadless solder' can contain up to 5% lead !!!

and never drink tap water out of the hot side: the lead laws are only of recent vintage, like the 1990's .. and hot water + old lead in older pipes means the water will dissolve some ..not good!

Always (still!) wise to run the cold water faucet a while, in the mornings!

Are you rounding the edges any on the inside? Just wondering if you had any issues with it rubbing or cutting the finger when it's worn. Another great looking ring sir!
Mrballeng (author)  RedneckEngineer3 years ago
Yes, while the ring is on the sand paper wrapped drill bit I remove any sharp edges. But since the coat hanger was round to begin with the edges aren't very pronounced anyway.
scoochmaroo3 years ago
Awesome! I think the second or third picture in the Intro step would make for a more striking main image.
Mrballeng (author)  scoochmaroo3 years ago
Done. Thank you.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!