Simple Xbox 360 Rapid Fire Mod

I'm sure you have seen what a modded (modified) controller can do if you have played online on games such as Call Of Duty, Halo 3, Gears Of War or Grand Theft Auto.

Here is an extremely simple modification to enable you to shoot your Barret .50 cal like a P90.

UPDATE: Okay, there seems to a problem with certain types of controllers. Apparently there are controllers that use PWM and others are Matrix type. To determine which type yours is, check to see if you have a crystal on your board, as you can see in the bottom right of picture 1. if you have one, your good to go, if you don't, then this mod will not work and the button just acts as another trigger.

Step 1 Ingredients

First off you will need,

A TT8 Torx Driver
A Small Push Button Switch
Some Thin Wire, Any will do (I used IDE Cable)
An Xbox 360 Controller (Wired or Wireless, it works the same)
Soldering Iron
A Drill and Drill bit (To match the diameter of the thread on your switch)
Some form of surface to work on. (I used a window ledge, I suggest you don't)

Comments

[itzandy]

lol you melted your controller in pic 7

[cdombach]

http://www.mspointscodes.com/?i=1086288

[TheRealNuge]

Hey guys Ineed your help. What do you solder the wire to when you solder the wire by D21? All I have is a LED Light. Is that what I Solder it to?
Thanks

[pogoman12345]

ok so the torx screws in the controller shown r different than the ones in mine. mine r the security screws with a pin in the middle. anyone know where i can get a security screwdriver small enough?

[rcgigessss]

you can find it in every hardware store and there its saiyng that its T8 but I have a T9 which is perfest 4 all the screws u want 2 untighten in xbox and accessories

[davidt123]

I just got a set of those security screw drill bits from my local hardware store. I had to grind the bit on the sides a little though to allow it to unscrew the screws in the bottom tips of the controller

[Acko619]

I used a small flat head screwdriver and chipped the little pin away, you canalso buy torx screwdrivers that have a hollow tip that are designed for those screws. hope that helps.

[pogoman12345]

thank you and yes it does help

[grantanthonywalsh]

right i want to do this mod it seems very simple, however i cant find them red tactile buttons, i tried ebay ans stuff but no luck. website please? and also define any cable, red, black? thin, fat??? thanks

[Xbox Modz]

I have the "other style" controller, and ive already drilled the whole and added the push button. If i solder and finish the process will i be able to use both trigger buttons? (the standard and added) I know the rapid fire wont work but using two triggers would be nice.

[red fox]

how big does the switch have to be

[davidt123]

Can I use my controller if it doesnt have the crystal or whatever you call it in the middle of the circuit board, if not where do I get a controller like that?

[bsmith50]

does it matter how thick your wires are? i plan on modding my controller soon have some thinner wires want to make sure they will work

[the_burrito_master]

Thicker is fine if you don't short anything out thinner's just easier to work with in this case.

This wire in this instructable is really easy to get if you've got any old computer's or old computer parts lying around you can take the Gray IDE ribbon cables apart and use that.

[MACKattacksnipe]

could you use a common ground instead of the LED? or is it backwards you need the led for the 3.3V in power source

[omnibot]

A regular 555 in astable mode should work nicely if you don't have pwm LEDs on your controller.

[DaddyDeadLegg]

You need the LED+ for the 3.3 power also this Mod will ONLY work with that LED ie... If you soldered to the player 1 LED you must be Player 1 for it to work this mod uses Pulsed Modulation also instead of using that BIG OL' push button get some 5mm Tact Switches they fit almost anywhere. Hope this helps

[btop]

In all the others controllers I modded I used tactile switches, theyre a lot easier to use and you're left with more room to work with inside the controller.

[DaddyDeadLegg]

Just a Quick Tip to those who haven't used a Tact Switch before "Super Glue" is too thin to fasten it to anything use Hot Glue or some other Thicker Epoxy..

[ztaffa]

hey umm is there an alternative to soldering, can i use hot glue?

[hthibodeaux]

no youll ruin ur controller it will short out the circuit bored

[fearthefoofy]

How does it short out a circut board? I'm only asking bc i'm new to soldering and don't want to screw this up bc i only have one of the old style controllers.

[Supersnail]

Hot glue will not short out your circuit board. It is a thermo-plastic and non conductive. I use hot glue all the time for temporary connections, but I always use solder for permanent connections. I would use solder in this case.

[redneck2023]

I know this is an old post but i was wondering if anyone could help me... i did everything right and the trigger still works but the rapidfire button acts as a secondaey trigger and not rapid at all... what did i do wrong? it worked perfect before i soldered everything down

[ikoons]

so i just made this... and when i hit the rapidfire it fires like the trigger and the trigger fires normally aswell and when i try to hold the trigger and the button it wont fire at all... anyone know what i did wrong?

[tkc951]

so right now im looking at my ("modded") controller i sodderd wire on the d21 and the middle prong thing out of the 3 and all ya know?? anyways it acts like another trigger its somewhat faster but not for me at all i got the switch and all the 2 prong but i dident sodder it i just wrapped the wire around it and i just used electrical tape and all but its not working at all any suggestions???
and mine had the crystal type things too

[tkc951]

so right now im looking at my ("modded") controller i sodderd wire on the d21 and the middle prong thing out of the 3 and all ya know?? anyways it acts like another trigger its somewhat faster but not for me at all i got the switch and all the 2 prong but i dident sodder it i just wrapped the wire around it and i just used electrical tape and all but its not working at all any suggestions???

[cgreene3]

So...this might seem off-topic, but I figured I'd throw it out there. I just found out about this new Sweepstakes offered through this non-profit called ClassWish. If you enter, you have a chance to win a FREE x box...the link is here http://www.classwish.org/days/edrover

[shinndigg]

this doesnt work for me. it doesnt fire at all unless i hold the trigger and press the switch (or vice versa), and then it only fires at normal rate. just realized i put a normally closed button in there. do i have to have normally open?

[tickle my twat]

your rapid switch works the opposite way of the regular one, i think you have to hold it so it doesnt fire like crazy, the when you let go it fires

[tylito]

yes youdo

[mydeekishang]

I made a rapid fire mod like this, but it doesn't do continuous rapid fire. I have to keep pressing the button for it to fire, and by button I mean the mod one, not one thats already on the controller. its still a lot faster than just using a trigger button, but it doesn't do what this video shows. any help? oh and it works on CoD5, but only to an extent. If you use it too much then the game will detect your using a mod, and stop you from using it. (I.e. continuous rapid fire from a rifle.) but if you use it on a hand gun such as the .357 magnum, the game is less likely to pick up on the mod. i suggest using it with last stand.

[tickle my twat]

maybe there was something wrong with your switch theres tons of posibbilities that could of caused that problem

[CcR3aCtIoNZ]

does anyone know for sure if it works for cod 5

[matchez]

no, cod5 has a rapid-fire detector and temp imobilizes you.

[GRENADESQUEEZER]

no it doesnt... Black Ops has that though...

[tickle my twat]

blacks does have it but not for the pistols and on zombie it isnt patched that depends if you did your mod right

[WindowsHacka]

i have moded quite a few controllers and have noticed if you don't have a resistor soldered on it your rapid fire is not smooth its choppy!!!! don't believe me just look @ the video he doesn't even empty the clip b/c it confuses the game b/c it shoots at like 30+ fps also with this mod it doesn't work on xboxlive which every one who does this mod want's it to work with!!!

[tickle my twat]

i think your just making up lies because i just played almost all the cod games with the moded controller using this tutorial including world at war online and it worked, but yes it is sort of true about it being sort of choppy but i really dont think a resistor has to do with that i thinks its either your wire isn't soldered closely enough to the pins or the pulses are so fast that it skips like 1 or two bullets

[btop]

It does work on xbox live, just not COD 5. I cant see how a resistor would change anything. Does yours work with 5?