This is not my idea, its been floating around the internet for a while. Its a simple and cheap way to make a padlock shim out of a can of soda or any thin metal.

Remove these adsRemove these ads by Signing Up

Step 1: Parts

The only real parts you need for this are a can and a pair of scissors or a razor. If for some reason you dont have a can you can use any metal of the same thickness or slightly thicker.

Step 2: Prepare the metal

Using the scissors, cut off the top and bottom of the can. Then make one long cut down the side of the can to get a sheet of metal. Then flatten out the sheet, and cut off the jagged sides of it, so you end up with a smooth rectangular sheet of metal.

Step 3: Make the marks and cut

The instructions I read for this say to use a strip 1" x 3", however I found it easier to use a slightly more squarish piece works better, so use something about 1 1/4" x 2 1/2". Mark out the rectangles onto the sheet of metal using a sharpie, and then cut them out.

On the smaller rectangles, mark off fourths both vertically and horozintally.

Step 4: Mark the M

Draw a M shape on the rectangle. The M should start out 1/4 in from the left, and shoud be 1/2 up from the bottom, it should curve down so the bottom part is 1/2 in from the left, it should be mirrored on the other side. Its kinda confusing so just look at the photos. After you draw it, cut it out.

Step 5: Folding and shaping

Fold the top 1/4th down, then fold the 2 side parts up and over. After you finish folding wrap it around a bic pen or some round object, roughly the same diameter as the bar on the padlock.

Step 6: Using

The best method to open it is to have the part of the shim that will go inside the lock on the outside of the bar. Push it down into the padlock, and then twist to unlock it. It can be very hard to master, dont give up. It will probably take a few minutes to get it to work. These are only good for a few uses, because they begin to crumple up and will no longer fit in the lock. A good practice technique is to use an open lock, look inside at the part you are trying to force open, and try moving it while the lock is open to see what you need to do when it is closed.
1-40 of 415Next »
Aluminum is too weak. I created this set in 1985 from a brass alloy which acts as a lubricant and is verry strong. The more you use them, the smoother they get. See my webpage concerning brass..
+1 As much as I love Arizona Ice Tea, I have to agree.
georion1 year ago
A flat blade screwdriver and 1 tap with a hammer is all i ever used, and neithr one ever wore out and got crumbly.
you seem to want to be STEALTHY--are yo up to No Good ???
GASSYPOOTS2 years ago
also works with floppy disc protected with metal covers (break protector off break into halves break 1 half into another half) but works the same way!!!!
mikeltv12 years ago
I just made this, and I am going to go to school and try this out on my gym lock.
Marcman7 years ago
dont get it
Me neither.
me neither.
me neither
me neither
me neither
me neither
me neither
me neither
me neither
CVJX xproplayer5 years ago
Me neither.
cd41 CVJX5 years ago
me neither
me neither
me neither
me neither
(removed by author or community request)
me neither
me neither (im a slave to trends)
DON'T EAT ME!!!!!!!!!!!!
way to break a chain...
Tommyhzy grue4 years ago
me neither
me neither
my never
Me neither.
Me neither.
me neighbor
Me neither
Me neither. I'm with mg0930mg on this one.
xinistrom kcls3 years ago
ahem, i get this :D
Ditto. Me neither.
me either
ok end this it gets very annyoing being email like 50 times a day from people replying
1-40 of 415Next »