Instructables
You don't have to be Jay Leno to own a jet powered motorcycle, and we will show you how to make your own jet enigne right here to power your wacky vehicles. This is an ongoing project, and plenty of additional info will be available on our website soon. See the full build at http://www.badbros.net

This information is brought to you by Bad Brothers Racing and Gary's Jet Journal
http://www.badbros.net
http://www.garysjetjournal.com

Warning! Building your own jet engine can be dangerous. We highly suggest that you take all appropriate safety precautions when dealing with machinery, and use extreme care while operating jet engines. Serious injury or death can occur while operating a jet turbine engine in close proximity, due to explosive fuels and moving parts. Extreme amounts of potential and kinetic energy are stored in operating engines. Always use caution and good judgment while operating engines and machinery, and wear appropriate eye and hearing protection. Neither Bad Brothers Racing or Gary's Jet Journal accept any liability for your use or misuse of the information contained herein.
 
Remove these adsRemove these ads by Signing Up

Step 1: Come up with a basic design for your engine

I started the build process of my engine with a design in Solid Works. I find it much easier to work this way, and creating parts using CNC machining processes turns out a much nicer end result. The main thing I like about using the 3D process is the ability to see how the parts will fit together before fabrication, so that I can make changes before spending hours on a part. This step is really not neccesary, as anyone with decent drawing skills can sketch out the design on the back of an envelope rather quickly. When trying to fit the entire engine into the final project, the jet bike, it will certainly help a lot.

I would also suggest that to get the best answer to questions if you are attempting to build a jet engine or turbine based project, subcribing to a user group is the way to go. The years of combined experience from various users proves invaluable, and I am a regular on the Yahoo Groups DIY Gas Turbines forum.
1-40 of 296Next »
ridalyn2 months ago

A note about aluminum, as the creators of the Bradley Fighting Vehicle can attest, when exposed to high combustion temperatures, it creates extremely toxic (read FATAL) gases. Be very careful if you intend to use aluminum for any of the core components of your jet turbine engine.

I am trying (somehow) to put this together with a waveboard to make it hover at least a foot. can anyone help?
f=ma my friend. it is the most important thing you will ever learn.
I'm assuming that f = either force or fuel. m = mass. what is a?
force = mass * acceleration. Newton's second law of motion.
i thought it was the third law of motion?
Nope, it's the second law:

From http://en.wikipedia.org/wiki/Newton's_laws_of_motion

Second law: A body of mass m subject to a force F undergoes an acceleration a that has the same direction as the force and a magnitude that is directly proportional to the force and inversely proportional to the mass, i.e., F = ma. Alternatively, the total force applied on a body is equal to the time derivative of linear momentum of the body
Rebreg simonches4 months ago

you are right, but never, never ever ever quote Wikipedia

ridalyn Rebreg2 months ago

That quote is a verbatim quote from my college physics textbook which predates Wikipedia by about 30 years.

force = mass X acceleration
How is this project coming?
115 lbs of me, plus at least that much in fuel and engine, not enough power to hover..... :(
Power to weight.
Fuel weighs a lot, engines more. You could, but check the price tag....

so i have looked in to these jet engines for a while now and ive found a designe for it and i am making a motorcycle version(most i have found for vehicles is a go cart type thing) so i want to know will the little portable grill propane tanks work im gonna use two of them on it one on each side to try and balance it better i just dont know if they have enough fuel for a short run or even that of driving it to like the store or somthing

please tell me how that works out ?

chriswillb6 years ago
Also can it be made out of aluminium
Aluminum is the best idea for a metal flying machine becaus it is so light and that is what they use on the big jets at airports so you don't have to worry about it melting of heat
I'm not sure if you guys have any experience working with metal or a whole lot of knowledge about metallurgy but steel would be preferable. I work with both a lot in my welding class, and though I like aluminum, it's not really all that strong and its melting point is about 1200 F, (which believe it or not isn't a whole lot for a jet engine) whereas steel's melting point is somewhere closer to 6000 F. It may be a little heavier but I think that since it's a stouter metal and more resistant to becoming liquid while you're trying to ride it makes it a better choice.

the melting temperature of steel is not that high, I melted a 2" thick jackhammer bit in my forge and it's not anywhere near that hot the melting temp of steel is closer to 3000 F

And if you get the bright Idea to use aluminum for some parts and steel for others bear in mind that anywhere aluminum and steel are touching will tend to cause both to corrode very quickly.
turbochargers have a steel turbine shaft that then has the aluminum compressor wheel attached to it with an aluminum nut. i have never seen one of these parts corrode like you have mentioned.
That doesn't mean it doesn't happen. Basically, aluminium is more reactive than iron. Where a ferrous metal (eg steel) interfaces with aluminium and there is water bridging the interface, it will effectively act as a shorted battery. In a nutshell, you're going to get aluminium sacraficing itself and corrosion occuring. Perhaps the internals of the turbo are kept real dry, hence you haven't witnessed the corrosion.
kschmidt2 hawksky9 months ago

That part tends to spin pretty damn fast, so it would stay dry, any water that formed on it before it started would be forced to the outside, and as it compresses the air it gets hotter, thus it will start to evaporate if it hangs around.

hawksky kschmidt29 months ago

That's true, but I'm sure most people stop the engine eventually. Moisture in the air could easily condense when the engine gets cold in the shed overnight.

it really depends on the parts man, some parts are not reaching extremely high heat, some are, for example, in a car, a forged iron piston is one of the best to use because its been tempered many times, and because of that, it is extremely strong, that is what they use in formula one cars;
however, a component such as an intake, can be very light as its not reaching as high heat as the pistons.
galvanic corrosion only happens when it is electrified though.

No it isn't.

A. Aluminum is very weak (I can bend a 1/2 inch thick bar easily)

B. Aluminum has very weak melting point

C. They wouldn't need to make it out of Aluminum because the engines have a 59,934 horsepower

D. Steel is stronger, so there for, if a bomb goes off it won't explode like a tin can full of firecrackers like aluminum does (tin cans are also made of aluminum).

E. steel is cheaper than aluminum.

F. Research your comments before posting them (you can see I made the same mistake on this Instructable already.)

A. Aluminum alloys can be stronger than steel

B. Aluminum alloys have higher melting points

C. Making an engine out of steel would make the engine weigh 2 times as much greatly reducing the efficency (pardon my spelling)

D. How would a bomb go off in or on an engine, and aluminum alloys are more resistant to explosive forces

E. ... We'll that one is true

I would say for a personal jet engine aluminum would be an ideal material

ok i made a few mistakes when typing.

I meant if a bomb went off IN or ON the engine (also aluminum would heat up a lot from the friction causing warping, etc.)

AND I deleted my stupid comment from before.

I know this is old, but most aircraft engine parts that are part of the combustion/exhaust system are usually made of titanium for it's weight/strength ratio. Aluminum is used mainly in the structure, where high temps aren't an issue
gee i think we have an aviation expert on our hands here
actually, hes right... the plane is made of an aluminium alloy, the engine isnt, it would be idiotic to build it out of aluminium, it will not hold up.
thats what im going to wrap around the engine when i build my ultralight plane wich i will build out of aluminum
does it power enough thrust for a small homemade single engine ultralight aircraft

I would not think so. The Engine would require a source of wind (I.e leafblower in this case) and a fuel source as well.

JediDude62055 months ago
(removed by author or community request)

Unfortunately, your comment is not very clear. Are you implying that the link in your comment is the original? If so, then I suggest you check the username of this instructable and the author of the linked page.

my bad. Nice jet engine by the way. what make and model do you need for the turbo?

matt21century7 months ago
atatistcheff9 months ago
One of the URLs in this article is non existent and one is hosting malware. They need to be removed.
bobdude9 months ago
very dangerous...
how fast does your "toy" go?
1-40 of 296Next »