Instructables

Step 1: Gather the materials and tools

Picture of Gather the materials and tools
Gather the materials and tools.

Dremel
2 x Standard USB to Micro USB cables
Black Spray Paint
Bluetak
Hacksaw with wood cutting blade
Single sided sticky foam
Wood

Felt (Which I didn't actually use, as I could get the controllers to fit)

Step 3: Create the holes for Micro USB connecter and cables

Using the Dremel with drilling bits, sanding bits and material removing bits measure the holes and start removing material.

This step took a while as it was a bit hit or miss whether I got the holes in the right place.
Also remove material from the underside of the wood to run the cables.

Step 5: Finishing up

I used a piece of single sided sticky foam to close the bottom of the wood off, aswell as giving a good surface to touch the table top.

I also attempted to apply the felt to the control sections but found I didn't cut the holes big enough to fit. Having gotten so far I didn't bother removing more material to use it.
 
Remove these adsRemove these ads by Signing Up
camb006 years ago
for running it on the mains you coul buy a ipod thingey and mod it or spray it ..........
You could attempt to find out the voltage delivered to the controller (I'm guessing it's somewhere between 5 and 7) and find a cellular phone charger that uses the same voltage and also has a mini-usb plug. The mini USB plug is pretty common on newer phones, so as long as the voltage is within a tolerable range, it should be pretty painless to replace the USB cables with USB chargers.
for some reason u cant charge a ps3 controller with that it only works on a computer.
Arathefu ktalex4 years ago
You're wrong, DS3 can be charged with almost any USB port.
ktalex Arathefu4 years ago
I tried to charge it on my bluetooth headset charger but it just wouldnt charge.
Arathefu ktalex4 years ago
Maybe your headset charger is somehow protected against charging anything that's not a headset?
you need to get two 100k resistors (per remote) and connect one end to =ve and the other end to data.http://www.instructables.com/files/deriv/F6M/Z2D7/H8I43UEB/F6MZ2D7H8I43UEB.THUMB.jpg This works on apple devices too. it is used to protect the device from too much current/voltage, so use at your own risk. but works for me.
usb smart cherger.jpg
it is 3.7 volts
Great Instructable. I've started making one based off of this except I am making it vertical with 4 controllers as to save space. I will post photos when I am finished.

Also, I have also looked into the USB powering issue and from what I have researched, the absolute maximum amount of power the can be drawn from a USB is 500mA. as long as the device reqests and is given more then the 100mA baseline. My USB keyboard that I use for the PS3 draws 5V --- 250mA and works fine.

Therefore one could conclude that since a PS3 controller draws 3.7V and only 30mA (it's on the back of the controller) then is is definitely feasible to have 4 controllers. Even 7 which is the max the PS3 can recognize. While 3 controllers would still be under the 100mA baseline. As far as the voltage, it would be shared through all the ports. ( I think)
well no. you dont understand. its not the voltage that the back of the controller uses. if you take apart the controller and you look at your battery its just telling you 3.7 @660 Mah. while the controller takes only 30ma. well by doing the math you can tell how long the battery will last charged. and the battery says 4.2v charge at maximum for charging. but you may not know that this is just for the battery. the controller consumes some voltage too. so 5v is plenty to charge and play. this is how sony made is. but there should be some sort of pullup resistor combination that will trick the controller to charge. im still trying to find out what but the best bet is to buy a chinese charger and dissect it to see what makes it tick. maybe we will find the right resistors. or the right voltage with amperage plus some sort of chip to trick the controller..
Andrew2_24 years ago
some ipod chargers with usb ports might work
 i dont have access to bluetack, what would be a good alternative. 
darked695 years ago
nice job .. i hope that you provide us the measurements though
PKTraceur5 years ago
Nice Instructble, however I would add some more detail. I was having trouble grasping that the cable would stay, and if a controller was added, then removed, well, stay where it was put. ~RoAr
nice instructable! could someone please help me, my controller always wants to scroll to the left (maybey the left button is stuck)does anyone no how i could fix this? i didnt realy wanna open it up without an idea of what i was doing. thanks
this happened to my psp i bought a new joystick
its semi-sorted now if i turn the controller off then back on again its (usualy) fine
Push the stick in as hard as you can and jerk it to the right. This worked with my PS2 controller after I broke the thumbstick when I threw it at the wall.
thanks
collard416 years ago
i actually made one of these by vacuum forming plastic, and a DIY split usb cable so you only need one port on the ps3. the gloss plastic looks better than wood.
alexzander7 years ago
why not take one of them and conect the the power(the black and red one inside of the usb cable) from one of them and conect it to the other one so that you only get one cable ot and it looks eaven sweeter and i like your idea...
Jonny1983 (author)  alexzander7 years ago
Would that split the voltage and therefore not charge the controls?
no.
BLACKROD7 years ago
Great idea. Love it.
smudgie867 years ago
looks extremely sweet. Well Done
Blue_Dream7 years ago
OMG.. Loved It