Picture of Easy Pneumatic Potato Cannon. Fun and powerful!
A tutorial on how to make a cheap, pneumatic potato cannon powered by a bike pump from easy to get materials. It's really simple to make, but don't underestimate its power. They can shoot straight through a pretty thick sheet of plywood and break windows. Be smart and be careful when you are using one. Do NOT hold me responsible if you get hurt!!!
The pictures might be a little blurry, it's because I took them out of the video I made on how to make it.

Check you the video tutorial!

Step 1: Getting started

Picture of Getting started

-Two pieces of 2" PVC Pipe (any size)
-One 2" Non-threaded PVC End Cap
-One 2" PVC Valve (not threaded)
-One Schrader valve (from an old bike tire)


-A saw (to cut the PVC pipe to your desired length)
-A drill with a drill bit that is about the same size as the schrader valve
-PVC Primer and Cement

1-40 of 186Next »
Masher0071 year ago

This is not spam, but a warning. PVC will fail suddenly after a while. This was band member that hurt badly by a T-Shirt launcher explosion.


pj814 years ago
If I was you I would spend the extra five dollars to get the rated pvc. Mine can get up to 150 psi safely. It did explode in my face once, but that was because i was stupid and I pumped it up a few minutes after I applied the glue. At around sixty psi, I was still pumping and the barrel shot across my floor like a missile. scary as hell I thought I had hearing damage.

Same here, except mine had a 4 foot 3 inch chamber and had 120 psi in it. Dented metal lockers on one end of the room, busted a hole in insulation on the other end. I couldn't hear for about 1 minute, and couldn't hear normally for like 15, kids be careful, these are not toys!

Rehbein7 years ago
omg my parents think its to dangerous how do i convince them
science project? that's how i got my stun gun... (seriously)
Lol. I made nitrocellulose for mine.
what was the project?
well, just testing the conductivity of materials... really i just wanted a stungun :P *for science purposes, of course*
why not wireless power?
huh? what, you mean like conducting it through the air?
like using magnetic power to do wireless electricity I guess.
uhh... why??? it would only send whatever power was in the 9 volt inside the stun gun...
Well, how old r u? Responsibility with a deadly weapon is required to opperate it?
Phoghat Rehbein3 years ago
You do what I used to do and just do it and don't tell them?
make it out of steel and weld it together, like I did. Don't shoot lead slugs at plywood boards infront of them
amike1 Rehbein3 years ago
that's what friends houses are for...
fake it to max psi and dud shoot it slow valve open. or did you shoot it full already? if so... your SCREWED
camb00 Rehbein7 years ago
just say i gets me off my xbox/playstation/wii or whatever!!!!!!!!!!!!!!!!!!!!!!!
bwells24 years ago
I am building the exact same thing, but the schrader valve with the end cap and the pipe is 1-1/2"
jacko backo4 years ago
I built one. It exploded in my brothers face and he had to get 8 stiches. =(
skelly74475 years ago
Never use a plastic ball valve. After a few months it will stiffen up and be so hard to turn that it'll be useless. Use a metal ball valve. Even if a metal one stiffens up you can lubricate it with WD-40 or something.
you can use wd-40 on pvc too
zone4life5 years ago
im planning 2 make 1 and i was thinking is it good 2 have a bigger air chamber and a smaller barrel :)???????????
i use a 4inch pipe for the chamber and then use a 1 inch pipe for the connection between the barrel and the chamber. then a 2 inch for the barrel. just make sure you get pipe made for pressure.
tulavatalo5 years ago
at wath presure will this blow up im my face
normal non rated pvc that they sell at lowes and other places made for plumbing should be no higher than 45 psi
Depends if your using crappy pvc or being unobservant and kill yourself because you messed up the valve! :D
OKJEFF44 years ago
If you are worried about it blowing up, use ABS tubing. It should be rated for higher pressure. Also, ABS doesn't splinter if it explodes. PVC tends to shatter into lots of pieces.
zone4life5 years ago
also how strong is ti if its pumped um 2 50 psi ????
MoshBoshKid6 years ago
hello could you please tell me where you got your valve and how much ?
Hello, ever heard of a hardware store?
mate i live in the uk and they are like £90 cba paying tht much
Find an old bike/ an old bike innertube.  Cut it off from said innertube.  Ask friends if they have any old bikes. 
noo i mean the huge pvc valve i cant find em anywhere in the uk for cheap
i have found a uk website where u can by a valve very cheep as well as pressure rated pvc pipe here is the linkwww.pipe-out.com/index.html
The site barely works and the valves that i can see are too small but the big ones when i click on them the page is blank :( thanks for trying
GroovyGuru6 years ago
Thanks for posting this! I made a few custom changes to turn this into a Halloween Candy Launcher (which I explain below). But here's a quick video I made:

The video shows pressure at 20 psi. The projectile is a foam type ball we use in the pool. I purposefully tested this with something soft to avoid smashing the neighbors windows. I'm sure a heavy object with better/less wind resistance (aka an actual potato) could easily be sent down the block and do some serious damage.

Trick-or-treaters will be greated by a Blue Man at the door who will "launch" their treats into the yard. I really just need something to put it over their head and into the yard.


(1) I wanted it to sit on the ground so I didn't have to hold it.

(2) I wanted a smaller launch tube, but didn't want an 8 foot long 2" tube (which would approximately equal the same air volume as a 2' by 4" tube).

Changes and Comments:

I used a 4x4x2 junction and put the 2ea 1' by 4" on each end. Then I cut a lenght of 2" tube long enough to put the valve at a comfortable height. This also solved problem #1.

I used pipe that is rated to at 220 psi or more.

I still wish there was a better way to mount the valve. -- The valve is my weak link. I used Locktite which took 48 hours to dry, but it still leaks a bit. If I get much over 20 psi it begins to leak out faster than I can pump. I have some ideas on how I can re-seal this without cutting everything apart.

Thanks again for putting this instructable together.

my advice , I've done it so it works, hot glue and duct tape. be generous on the glue AND duct tape.also wrap it TIGHT. you can star with electrical tape to smooth the edges THEN duct tape. worked great for me. the psi depends on the amount of glue and tape so wrap WELL!
how did you make it trigger powered
1-40 of 186Next »