Instructables
loading
loading
Picture of Easy Touch-Pad Stylus
sTYLUS PIX 026.jpg
sTYLUS PIX 027.jpg
There are many Instructables on how to make an Stylus. Well, I'd like to add to the pool and publish one myself. I saw how to do this from a video by Collin Cunningham from Makezine. It is his idea, not mine. I figured that it should be made into an Instructable. Enjoy!
 
Remove these adsRemove these ads by Signing Up

Step 1: Video!


Step 2: Stuff

Picture of Stuff
sTYLUS PIX 003.jpg
sTYLUS PIX 004.jpg
sTYLUS PIX 006.jpg
sTYLUS PIX 005.jpg
sTYLUS PIX 007.jpg
sTYLUS PIX 008.jpg
sTYLUS PIX 009.jpg
This is pretty simple. All you need is:

Materials:

-Cheap Pen
-Wire
-Conductive Foam. This is the most important piece! ( if you buy a kit from the makershed, adafruit, etc that comes with a micro-controller, the foam is the stuff that protects the chip pins.)

Tools:

-Tape
-Scissors
-(Opt) Wire Strippers

Step 3: Pen Prep

Picture of Pen Prep
sTYLUS PIX 010.jpg
sTYLUS PIX 011.jpg
The main body of the stylus is a pen. Disassemble the pen completely. Throw away everything except the tube. My back end did not come off so I had to take scissors to it.

Step 4: Conductive Foam

Picture of Conductive Foam
sTYLUS PIX 012.jpg
Now that you have your pen ready, take your conductive foam and grab an object with a touch screen. Hold one end of the foam and try using it on the touch-screen. If it's conductive it'll work like your finger. If it works, cut a piece of foam slightly thicker than your pen tube.

Step 5: Prepare the Wire

Picture of Prepare the Wire
sTYLUS PIX 013.jpg
This step is pretty easy. Strip the insulation off of the last 2" of the wire.

Step 6: Foam + Wire

Picture of Foam + Wire
sTYLUS PIX 015.jpg
Now that all your pieces are ready to go, it's time to assemble:

Thread the un-insulated wire though the top of the conductive foam. After that, tightly wrap the wire around the top of the foam.

Step 7: Into The Pen

Picture of Into The Pen
sTYLUS PIX 017.jpg
Now take the foam-wire and thread it through the front of the pen tube. Pull the foam through as well but leave about a quarter inch on the outside.

Step 8: Wire...Again

Picture of Wire...Again
sTYLUS PIX 019.jpg
After all that, it's time to strip all the rest of the wire that comes out the back-end of the tube. What you do now is secure the wire with a small strip of tape.

Step 9: Wire Wrap

Picture of Wire Wrap
sTYLUS PIX 022.jpg
Now what you do is wrap the un-insulated wire around the tube. Next, tape the wire down near the front of the pen to secure it.
esmeatsix3 years ago
thankyou! I've made one and it's worked really well! I used gold woven wire so it looks decent as well. I didn't have any conductive foam and couldn't order online but I went to Maplins and found some there :) Only problem now is that the rest of my family is pestering me to make them one!
mmdr12993 years ago
Hi, Do you know if this would work as mouthstick? I have a user that I work with who has a physical disability and draws using his mouth. I ma not sure about the safety/conductivity with using the mouth. Any info you can provide would be great.
This is funny, I made an almost similar one, it works a lot and you don't need work so hard. http://www.instructables.com/id/Touchscreen-Stylus/
gcoma4 years ago
This is BRILLIANT! :D I want to try!
I was wondering where the conductive foam came from. Obviously not wondering enough to look it up. Nice 'ible.
If you used a metal pen you wouldn't need the wire on the outside. Stainless would be pretty. Just make sure you strip any varnish off the outside and where the foam touches the barrel.
fruitkid101 (author)  mr.incredible5 years ago
Hey thanks! Great idea for the pen. The stainless steel sounds good too. It wouldn't have to be a pen though, you could just go out and buy a small stainless steel tube. A quarter inch diameter would be perfect.

You can buy conductive foam online. If you are familiar with the makershed or adafruit industries or solarbotics, or any electronic kit-selling site, they package their micro controllers in conductive foam. I think its to be an anti-static or something.

Cheers!
Well thats odd, I was looking at this instructable, and i reminded me of a kit I ordered in 2006. I though it should have had some of that special foam in it but the electronics were only in regular foam.
I found some antistatic bags from my motherboard and i cut a piece and it works fine
Can this scratch the screen?
fruitkid101 (author)  mAd tinker3r4 years ago
Not in the slightest :)
this is awesome man!
danyforreal5 years ago
I don't work with electronics so I have no reason to order from the maker shed to acquire foam from it's packaging. I looked up conductive foam and I get a myriad of sites that sell that stuff but I don't know if I should be looking for a certain type of material. Could somebody link me to a site that has the stuff I need? I really want to make a few of these for myself and my family.
fruitkid101 (author)  danyforreal5 years ago
Sure! Here is a link. http://www.hvwtech.com/products_view.asp?ProductID=525&utm_source=Google&utm_medium=Product+Search&utm_campaign=Product+Search+%28May10%29

You can get a whole sheet for just like 5bucks and it will last you years. No I'm not kidding, one of these sheets can get you a whole lot of stylii.

Have fun making these for your folks!
Gracias!! I'll post some of my creations!