Picture of Electric Mountain Board
ElectricMB 046.jpg
The goal was an electric conversion with minimum damage to the board and the ability to remove the system for standard riding.
Remove these adsRemove these ads by Signing Up

Step 1: Parts and Tools

Picture of Parts and Tools
I tried to get as many parts as I could locally but most had to be ordered online. The prices are approximately what I paid. Total cost of the project not including the board was about: $350

Board: MBS Core 95 from MBS Mountainboards. $300

Brakes: MBS V5 Brake Kit also from MBS Mountainboards. $60

Motor: 24V 300W Electric scooter motor from my local scooter shop. $30

Sprocket and Chain: Scooter sprocket and #25 chain also from my local scooter shop. $20

Steel pieces: 16ga sheet steel, perforated square tube (14ga), perforated bar and two flat bars (14ga) from Lowes. $20

The batteries, charger, controller and throttle were all ordered from Monster Scooter Parts.

Batteries: Two 12V 10 Ah scooter batteries. $65

Charger: 24V 1.6 Amp XLR Battery Charger and XLR charging socket. $38

Controller: 24V 500W Universal Voltage and Speed Controller. $33

Throttle: Generic 4-wire thumb throttle. $13

Other parts: Wire, electrical tape, wire connectors, nuts and bolts, zip ties, tie down straps. $35

Tools Used:
Socket set
Adjustable wrenches
Hex key wrenches
Drill and bits
Jigsaw and blades
Metal files
Wire stripper
Chainbreaker - $30 from Monster Scooter Parts

Step 2: Mounting the sprocket

Picture of Mounting the sprocket
ElectricMB 005.jpg
The MBS brake system comes with the mounting hardware (screws and spacers) needed to mount the sprocket to the wheel.

I used the pattern from the brake rotor to drill holes for the mounting screws into the sprocket. The initial holes were then widened to allow the mounting screws to sit flush against the sprocket.
1-40 of 189Next »
PaoloC22 months ago

i embraced the challenge and started too!!!
i got a core95X and 1000w system

i m having just a problem with sprocket.
as i m dividing brakes and engine system, i don t have the brake platter to drill.
my rims are the classic mbs ones with 3 screws and they don t really fit the sprocket screws.
would it be better to forge a metal platter of half cm, to have a spacer as well?
or i dunno if there are any good ideas for this and the engine mount... :/

ИвоН7 months ago

I'm thinking of making this but a bit different. Using this board + the breaks (Are you sure all i need is the breaks and a drill to mount the sprocket ?) And then using similar setup to yours to mount 2x500w (scouter, reversible) motors on the back. This would be enclosed in tight box, and somewhere near my back foot there would be batteries to allow bigger range(+ the ones on the middle). Any thoughts?

What is your current avg. range in miles/km (give or take a few) ?

Vurp (author)  ИвоН7 months ago

All I used to mount the sprocket was the brake kit plates as a template and a drill. Sounds like it should go pretty fast. I haven't used my board in quite awhile and never calculated an average range but the higher the amp hours on the batteries the more range you will get.

Does it even steer?
Vurp (author)  instructableduke9 months ago
It steers but not as well as it did without the motor. Turning around requires a larger area.
Progress so far. I removed the sheath that housed the cable for the breaks and replaced it with a cable guard. I tethered the handle bar to the board with some 550 para-cord. I have mounted the motor to the truck and its surprisingly sturdy. I haven't gotten a chain and sprocket or mounted the motor control. 1000w setup.
Update: the worst part of this project is finding the right chain (in my case 05T which is what came on the motor) I've already spent ~$40 in sprocket and chain. It may come down to spending another $40 to get a chain/sprocket set from a motorcycle/scooter store. I have no scooter stores around here, its all dirt bikes.
chopstx3 years ago
Great idea, now im hooked after watching videos on youtube of these things.... :)

I have a lot of questions tho before i start spending money on the wrong stuff.

Is your setup 1 wheel drive? Do you need 2 motors(one on each wheel) and 4 batteries to make 2wd version? Wouldnt the board always turn with 1wd?

Would a Atom 90 be suitable for this?

If I am 140 pounds could i get away with a 400 watt motor? And still have good torque and speed? This would just be used for going around the neighborhood and on trails, not legit mountain boarding.

any way I can use a lever handle for throttle?

Thanks alot and great 'ible!

Vurp (author)  chopstx3 years ago
It is one wheel drive and I have never noticed any turning.
The MBS Atom 90 board should work fine.
Depending on how fast you want to go I would try to get the biggest motor you can afford, a 400 watt will get you around but wont be super fast.
The throttle on this is electric so if you mean a lever throttle that uses a tension wire to control speed it wont work with this setup.
Good luck on your build.
chopstx Vurp3 years ago
thanks! do you have any experience using rc motors and esc's instead of scooter stuff?
Vurp (author)  chopstx3 years ago
Never used those but I have looked at some of the other builds that have them and they seem to work really well.
chopstx Vurp3 years ago
Yeah I think that if they will electronically work together, I would like to use a 750 watt scooter motor with a rc esc and controller.

I still have some research to do so if anybody that sees this has tips, tricks, or info that could help me build an electric mountainboard, I would greatly appreciate it!
RC ESCs are three pin/output where as scooter motors are only two. This is because RC motors (brushless I assume) are different in making than Scooter motors. an ESC with a scooter motor just wont work. Look at my other post where I got my scooter motor kit. Im waiting for it to come in the mail. Once its done, I'll post pictures and a video of it.
evanwehrer2 years ago
How much does this weigh?
Vurp (author)  evanwehrer2 years ago
The batteries and motor are somewhat heavy I would say it weighs about 20-25 pounds.
As soon as I can get some money saved up, I'm going try this out on my MBS Atom 90 board. I've already bought and installed the braking system. Now I'm trying to come up with a mounting plan to work around the brakes.

Do ya think 1000w might be a bit overkill? Im a 6ft 3in, 220lb guy, so Im just at the weight limit for this particular board. I've done some down hill and some jumps before I installed the brakes to see how it does. It hasn't broken yet.
Vurp (author)  The Expert Noob2 years ago
I think having more power is better even if you don't need it. You can always use less throttle if it is too fast. Not having enough power will mean slow speeds and more hassle to change.
TSC2 years ago
This is awsome! My brother would like to build some like this!
awesome! i made something kinda similar-ish to this, but i used a longboard and i didn't want to have to go to the trouble to build a drive train (i have fairly little time, as i have a 3 hour commute to school every day, and sailing team practice 3 days a week) so i used a 60 amp 12 volt (720 watts) brushless motor and a propeller. i mounted a 9" long piece of 2x4 on the back sticking up, and mounted the motor and propeller (in a pusher configuration) on that. i run it off a 3,000mah, 12 volt lithium polymer battery, and an rc speed controller. i control it using the r/c system i use on my rc planes, but it would work fine with the $20 radio available at hobbyking. below i have links to where i got the supplies. it takes a while to accelerate (0-20mph in 29 seconds lolol) and can't climb hills, but it's great fun on the flat just cruising around town, just be careful to shut off the throttle when passing people so as not to cut their feet off.
parts used:
speed controller

radio (not the one i used, but much cheaper, and better for this application):
chopstx3 years ago
If possible, could you provide a close up of the drive wheel with the sprocket? I want to see how you mounted the sprocket. Thanks!
Vurp (author)  chopstx3 years ago
I couldn't find a close up, but I used the hardware from the MBS V5 Brake Kit and drilled holes in the sprocket that matched the brake kits rotor. The hardware is basically a spacer and bolt that lifts the rotor away from the wheel.
chopstx Vurp3 years ago
Ok so do you think I would need the brake kit to drill the holes or could i just drill them based off of how I need to attatch it to the wheel?
Vurp (author)  chopstx3 years ago
You could do it without the brake kit if all you wanted was the sprocket mounted to the wheel, i think it would just take some good measuring to get it centered.
DustySeven73 years ago
you can use RC batteries, you have to wire them in series and then a parallel.
These guys took a electric longboard using CIM motor.

here is the battery they used

the battery wiring is on step four
if you wanted to use the motors they used look at step 5 and 6
i built one of these and have two more frames welded would anyone want to buy a complete 24volt 900watt version on a steel frame?
this is probably a stupid question but i ride goofy ( right foot foward) so if i buil this would i need the motor on the otherside e.g rear wheel drive?
Vurp (author)  WillERoberts3 years ago
Yes the motor would be on the other side. You can also reverse the foot straps I think.
do u know of a way to make the board go 20 mph without raising the price to much?
Vurp (author)  mountainboardpro3 years ago
The higher the wattage of the motor the faster it will go but if you have to buy the motor that also increases the price.
Hey, Vurp
do u know if a 24 volt baterie would work instead of 2 12 volts and would it affect the speed and the other parts?
Vurp (author)  mountainboardpro3 years ago
One 24V battery would work the same as two 12V as long as that is the voltage your system is setup for. Also the higher the amp hour on the battery the longer the charge.
shadowman24 years ago
How about putting a 300 watt(low rpm) motor on each wheel (yay for 4x4!!) And 20 laptop li-ion batteries underneath the board. This would be pricey, but the looks and power.. Maybe even a large capacitor as Bowmaster suggested (for double power at startup, since the motors would be direct-drive to the wheel. I wanna build this three years from now when i return to Canada.
Or maybe 2 1kw motors on each axle with chains!
This has already been done :D :

Can't even begin to grasp how awesome this is....
Your link seems to be malfunctioning sir/madam, it may require revising
You seem to be correct :D Here's a working one:

enjoy, the guy who has made the board posted other videos ;)
sheen1104 years ago
hi vurp, could you help ,me out here ? iv damaged the thumb throttle when dismantling it and dont have a clue how it was wired

inside it has blue, orange,yellow and red
orange and yellow are contected fine and it lights up but red blue and white are cut. would you be able to remember how its supposed to be . ? i havethe same throttle as you.

Vurp (author)  sheen1104 years ago
I never fully dismantled my throttle so if you mean on the inside Im not sure where they go.
nitram1354 years ago
 I have 2 12 volt batteries that are in series that i want to connect to a 24 volt controller but when the controller touches the battery, i get a lot of sparks. Does any1 know why?
1-40 of 189Next »