Step 14: All Done!
Time to test out! Pick up a phone, wait for the dial tone, and put the corner of the card on the microphone. Tap it once and your number should be dialled.
Click here to see a video of the card in action - I'm afraid it isn't the world's most exciting video, but at least it will show you the card in operation. The dialling tones are very quiet, so you might need to turn your volume up to be able to hear it.
I did warn you that this took a little skill to make, and that it was very experimental - I get around a 50% success rate maximum at the moment when dialling on my home phone only by considerable tweaking of the mounting arrangements, and getting the number recognised accurately is highly dependent on a number of factors including your exchange and the mounting of the piezo disk, including the shape of the cavity cut inside the card. I may work on some improvements to this design, as it could get recognition close to 100% (have managed to do this now using the computer to drive the card as a simulator - for those who are very technically minded, I could redesign the card to drive the piezo with a pseudo sine wave rather than a square wave using filtered PWM signals, and increase the tone and space times as well.), although I probably won't bother doing this unless anyone was interested in getting these sort of cards produced in bulk, (which I doubt!). If you are still interested in how the design works, and are a bit of a techno-nerd like me, then check out the technical notes below to look at how this whole thing works.
In case you were wondering, this doesn't work from a mobile phone, as you need a dial tone from the exchange for it to recognise the DTMF tones generated, but as I mentioned, this is more of a novelty marketing exercise than a universal way to dial a number- certainly, it shouldn't be attempted unless you are really up for the challenge of improving the design. It is hopefully also a neat tutorial into some other useful techniques like designing enclosures for miniature electronic devices using ID cards and getting nice graphic overlays done. Finally, hopefully it will also inspire some ideas for other electronic business cards - certainly some of the ideas that people have emailed me privately since posting this have been fantastic, so I know this at least is happening! Time for you to now start designing your own version of the world's most technically advanced business card!
Click here to see a video of the card in action - I'm afraid it isn't the world's most exciting video, but at least it will show you the card in operation. The dialling tones are very quiet, so you might need to turn your volume up to be able to hear it.
I did warn you that this took a little skill to make, and that it was very experimental - I get around a 50% success rate maximum at the moment when dialling on my home phone only by considerable tweaking of the mounting arrangements, and getting the number recognised accurately is highly dependent on a number of factors including your exchange and the mounting of the piezo disk, including the shape of the cavity cut inside the card. I may work on some improvements to this design, as it could get recognition close to 100% (have managed to do this now using the computer to drive the card as a simulator - for those who are very technically minded, I could redesign the card to drive the piezo with a pseudo sine wave rather than a square wave using filtered PWM signals, and increase the tone and space times as well.), although I probably won't bother doing this unless anyone was interested in getting these sort of cards produced in bulk, (which I doubt!). If you are still interested in how the design works, and are a bit of a techno-nerd like me, then check out the technical notes below to look at how this whole thing works.
In case you were wondering, this doesn't work from a mobile phone, as you need a dial tone from the exchange for it to recognise the DTMF tones generated, but as I mentioned, this is more of a novelty marketing exercise than a universal way to dial a number- certainly, it shouldn't be attempted unless you are really up for the challenge of improving the design. It is hopefully also a neat tutorial into some other useful techniques like designing enclosures for miniature electronic devices using ID cards and getting nice graphic overlays done. Finally, hopefully it will also inspire some ideas for other electronic business cards - certainly some of the ideas that people have emailed me privately since posting this have been fantastic, so I know this at least is happening! Time for you to now start designing your own version of the world's most technically advanced business card!
Remove these ads by
Signing UpFlag this comment as:
Not NiceInappropriateSpam
qorlis
says:
Sep 4, 2008. 6:23 PMReply
If the chip can be programmed to say something like "I am diabetic" with brief first aid instructions or an emergency number either spoken or programmed to dial, I could see this as a great emergency aid.
TwistedmindZ
in reply to Nov 1, 2009. 10:26 AMReply
i think the problem is that pic chips have a couple of kilobytes of memory if that. so generating more complex sounds would use a lot more memory, might have to have it external or something.
JOBGG
in reply to Mar 27, 2011. 5:51 AMReply
Aren't there those cards where you can save a message and when you open them it plays the message? They aren't that expensive, and you could have the whole thing independent from the PIC itself.
eight
in reply to Sep 4, 2008. 6:48 PMReply
Actually, as a single guy who dates a lot, this would have other uses ! :) Hey... Marvellous instructable. Thanks !!
tankboyben
says:
Jan 8, 2008. 8:16 AMReply
insane and absolutly amazing =oO. would love to have a go at that but i wouldnt have the 1st idea when it came to programing it, would like to have seen some back and side pics. top job dude
7
tomward (author)
in reply to Jan 8, 2008. 9:09 AMReplyYeah - must take a side pic - it really just looks like a strip of white that is 3.2mm thick. Back I didn't put on because it is just plain white!
c2p
in reply to Oct 3, 2008. 4:57 PMReply
by-the-way contact me at: fkern@c2p-inc.com www.c2p-inc.com
c2p
in reply to Oct 3, 2008. 4:52 PMReply
Hi Tom, The company I work for could make these easily. In fact I would be interested in helping you design the least expensive and thinnest card. I am thinking of making a bunch for the CES show in Vegas as a give-away. We would injection mold these. Of course I would give you all the glory. Smart design!
7
tomward (author)
in reply to Oct 4, 2008. 1:19 AMReplyGo for it, but don't underestimate the amount of work this design still needs if you really want to make it work properly as stated in the article - getting accurate DTMF recognition from an audio system just a couple of millimeters in thickness is not trivial, and will require quite a bit more development work. Good luck, though and look forward to seeing what you come up with!
34
jeff-o
says:
Aug 29, 2008. 6:40 AMReplyPerhaps a small hole on the back of the card, aligned with the hole on the piezo disc, would permit better conduction of sound from the card.
Jeebiss
in reply to Aug 31, 2008. 1:27 PMReply
I made one of these, and use a really fine, plastic screen over the ring, which concealed it, and still let through the sound.
1
Archive555
in reply to Aug 30, 2008. 7:26 PMReply
But it wouldn't look nearly as cool, now would it?
34
jeff-o
in reply to Aug 31, 2008. 4:39 AMReplyWell, you can't really see the hole in the corner, which I suppose is the point. But, you do want it to work as well!
1
Archive555
in reply to Aug 31, 2008. 5:27 AMReply
But there must be some way to make it work better, yet still look as cool.... Hmmmmm.... I wonder.... I've got it! Turn it into a robot flying death-ray UFO machine, and put the speaker in its mouth! Perfect!
34
jeff-o
in reply to Aug 31, 2008. 6:24 AMReplyHmmm, I think the goal of this project is to win clients, not annihilate them from the face of the Earth.
blueninja33
in reply to Sep 13, 2008. 11:30 AMReply
But what if you could do BOTH!!??!!??
1
Archive555
in reply to Oct 25, 2008. 2:19 AMReply
I like your thinking! What if the speaker instead said things like "BUY MY PRODUCTS OR BE ANNIHILATED!". And if they didn't comply, - BOOM! Destruction! Lasers! Cool sound effects! Hmm...
2
andros1200
in reply to Dec 22, 2008. 9:39 PMReply
Now that would be one business card I couldn't help but take from the little dispenser thingy.
gannon12raiders
in reply to Oct 14, 2008. 9:29 AMReply
Lol..
alfra
says:
Aug 23, 2008. 12:56 PMReply
so cooooooooooool!
hasiwally
says:
Jan 25, 2008. 6:07 AMReply
Cool Dude!!!!!!!
Visit Our Store »
Go Pro Today »
