Instructables
Picture of G Meter
I have a late 80's VW and the gauge cluster has 5 dummy LED locations underneath the other warning lights.  Well I was tired of the m not doing anything, so I decided to do something about it.  I came up with the idea to put a lateral gravitational force mater (G Meter)  in there place.
 
Remove these adsRemove these ads by Signing Up

Step 1:

Picture of
Gather up the needed supplies

If you wish to use your Arduino:

1- Arduino
5- RedGrenBlue LEDs (Mine are common anode)
1- Project box (if you don't want it in your dash)
1- 9v Battery
1- Accelerometer (I used ADXL 335 from adafruit)   http://www.adafruit.com/products/163
1- piece of Perf board
5- Resistors 1K ohm
5- Resistors 500 ohm
And some small wires for jumpers.

All parts needed if you wish to make it standalone:

1 -Circuit Board
1- ATmega168/328
1- 28 Pin socket
5- RGB LEDs (Mine were common anode)
5-Resistors 1K ohm
5-Resistors 500 ohm
1- 16MHZ Resonator
1- 104 cap
1- 10uf cap
1- 3.3v rg. (LM1117T)
1- ribbon cable
1- header connectors
1- Acceleromoter
1- 9v Batt. Connector

Here is the picture of the wiring needed for a breadboard setup.
The orange wires hook to the 500 ohm resistors and then hook to the RED LED cathode.
The Green wires hook to 1kohm resistor the hook to the GREEN LED cathode.
The common anode is hooked to +3.3v
X axis output of ADXL335 goes to PIN 0  (Picture is slightly different)
+3.3v and Gnd are hooked to power and ground pins of ADXL335
The AREF pin on the Arduino is hooked to +3.3v

Step 2:

Because I used COMMON ANODE LEDs:

"digitalWrite(led1G, HIGH);"    turns the LEDs to OFF not ON.
If you use common cathode you will need to change the code.

If you wish to change the pin number just change the beginning of the code:

int led1G = 2;
int led1R = 3;
int led2G = 4;
int led2R = 5;
int led3G = 6;
int led3R = 7;
int led4G = 8;
int led4R = 9;
int led5G = 10;
int led5R = 11;
int X_AXIS = 0;
infared0671 year ago
For this to be accurate, wouldn't the accelerometer need to be place very close to the center of gravity?
I don't think so as all parts of the car would be accelerating at the same rate with the exception of front or rear parts of the car when pitching but this is not going to impact the project noticeably.
Vrooooooom2 years ago
I wish I had a car with useless dash gauges! LOL
imperio2 years ago
a G-meter in the car what is the use?
kikiorg imperio2 years ago
You clearly don't drive fast enough. :) :)

(Of course, the better question is, "what use is a G-meter in a late 80's VW." :) )
bhouston (author)  kikiorg2 years ago
To answer the use of a G meter in an 80s VW- My brother jetta is currently pushing close to 350Whp. :)
imperio kikiorg2 years ago
it's true! I drive always at a speed below the speed of light
Well, if you know what how much lateral acceleration your vehicle can pull without slipping, you can use a G-meter to turn as fast as possible.
... why not?
andamas2 years ago
I knew that dash as soon as I saw it! I had an 84 Jetta GLi, man I miss that car, so much fun to drive.
dagaherz2 years ago
And... what about the battery?
Could you adapt the project to work in 12V or 5V to get power from the car?
Good idea...hummm my car has "lazy spaces" too!!!
bhouston (author)  dagaherz2 years ago
If you want to use the arduino I suggest using a USB 5v adapter or a 9v battery. If you use the board I designed it has a 3.3v regulator that will let you power it from car's power supply.
The illustration of the breadboard, connections and Arduino is very nice, what software is that, please.

I'd like to use that same style of illustration for my Instructables (yet to do one).
bhouston (author)  Machine2 years ago
It is Fritzing. It is free and REALLY easy to use.
http://fritzing.org/
Fo55ilise2 years ago
I like this idea but won't build it - it would only give the wife something else to complain about.
Machine2 years ago
How about adding a voice warning:

Level 1 says "Pathetic, can't you do better?"
Level 2 says "Marvellous, now she's beginning to tip."
Level 3 says"Yippeeee, nearly on our side."
Level 4 says "Call an ambulance and a tow-truck."
zmashiah2 years ago
Very nice!
I am actually building one myself with small Dot-Matrix display and ADXL345 sensor.
As for powering the unit, The boards specify 12V as their maximum supply voltage, and in the car the voltage can get slightly higher (13V is not uncommon), so I would refrain to directly power it from the 12V, but you could easily use a USB car charger to get 5V or put a 7805 regulator.
Machine2 years ago
That is a very nice idea.

Maybe it should make sounds too, the higher the G the higher the pitch...
That would be helpful in competing acrobatic airplanes but I think it would get really annoying really fast =P
Yeah... like that would never get annoying... :-o

(Just bustin' on ya)
bhouston (author)  askjerry2 years ago
Yeah I thought about that, and that's why I decided to install an off switch. :) I figured during the day wouldn't be bad, but a night it would really be distracting.
bumsugger2 years ago
Good idea for a novelty effect on my 1000cc Honda!
apzeiro2 years ago
What car is this?
I had in the past one here in Brazil. It had this same panel, It was called VW Gol 1991.
mikesters2 years ago
great, if I still had my golf II G60 I would install it there too :-)
almost a lightyear.JPG
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!