Gas Can Speakers

Em Destaque

Some novel garage speakers using plastic gas cans and a 2-way speaker kit. Standard 5L/1.25gal gas cans fit a 2-way 6.5" woofer/tweeter kit perfectly. As an added bonus, the pour spout serves to release pressure in the speaker can. You can get everything you need for ~$69 from Amazon and/or Home Depot.

Passo 1: Materials

  1. Pyle 6.5" 400-watt 2-way custom component system kit (
  2. 2x Scepter 5L/1.25G red gas can (I found these at Home Depot ~$11/ea)
  3. 2x Speaker terminal set (

Total: $69

If you don't have anything to plug the speakers into, here's my approximate setup:

  1. Any 2+-way amp, I used a Pyle PFA400U ( I don't necessarily recommend it as it doesn't have a standard AUX port or an FM tuner, but it does put out plenty of power to drive both speakers.
  2. Speaker wire (I used 12-guage,
  3. Banana plugs OPTIONAL (

Additional: ~$70

Passo 2: Electrical Dry-Run

I wired up the speaker kit components before delving into the enclosure. You might want to do the same to see how everything will fit together. The Pyle kit comes with everything you'll need except the terminals, including the +/- wire. Just wire the woofer, tweeter, and terminals to the corresponding +/- pins on the crossover. Test it out with the amp/stereo you'll be using. You may initially feel that the speaker isn't loud enough, depending on your amp of choice, but I promise when you get everything in the can and two of them side-by-side, it will be more than satisfactory.

Post a comment
Be nice!

Nós temos uma política de comentários em que todos devem ser gentis.
Por favor, seja positivo e construtivo.

mmo8we diz: Mai 20, 2014. 7:40 PM

How loud are these?

HannibalRex diz: Mai 9, 2014. 9:35 AM

Nice project, great job on the instructions. I ended up building this, and only have two suggestions or notes. 1) You can use the cardboard the speakers come in as templates for cutting your holes (woofer) instead of the provided template and extending, etc. Hey, I'm lazy so I found what seemed a quicker and easier method for me. I happened to notice how well the drivers shipped and so just cut out the cardboard holding them in the box. 2) Baffling - I'm giving away my secret here, but for about $15 you can get some nice, thick, egg-crate foam for beds from Target. The twin size is the cheapest and will do two LARGE floor speakers with plenty of left over. I just putty knife on some liquid nails and tack it all around the inside of the speaker enclosure. Usually this is one of the last steps so I can work around the crossover and wires. Oh, not needed for this build, but often in two-way speakers I build I'll cut the top rim off a round Tupperware, and coat it with textured ceiling spray or egg-crate foam on the inside, then using adhesive glue it to the back of the tweeter on the inside of the enclosure; help separate the bass and highs from being mixed, and forces more of the driver's sound to go out the front and not reverb in the back in the box. A little trick I learned from an old audiophile who used to build his enclosures out of marble! RIP Rollie DuChesne. Anyway, the only other thing I could say is I could probably use a bigger amp than the 100 watt mentioned in this article, no doubt these little speakers can take it. Nice amp though, I had to get it just to check it out, was a great suggestion, and I liked the features plus the remote. Oh, and use the spout (removed) for your bass port. You can tweak it as you wish/need to get the best bass "movement" of the air, I found I didn't need a tube for the port, just use the spout as if it were a real gas can. What I mean is assemble the spout as you would if you were actually going to pour gas. It's got a perfect "travel" length, and for most of what I was playing using an iPod it was right on with bass response/porting. Thanks again for this Instructable, was fun, easy, quick, and cheap. My friends didn't believe me when I told them my new "summer" stereo was going to be plastic gas cans! I did spend a little more on it, because I wanted to stock up on some of the banana plugs and enclosure plug/plates. The pictures are from my show and tell at work, and my Cattle Dog (Red Heeler) Texicali - don't worry about it being too loud for him, he's old and deaf :) Kinda like I'm getting to be! Had a lot of fun with this one, and having a lot of fun showing it off!

txje diz: Mai 9, 2014. 10:20 AM

Thanks for the feedback! Your set looks great. It's nice to know that someone more knowledgable than myself can comment on the acoustic qualities, particularly w/regard to the baffling and bass port.

fonguler diz: Mai 6, 2014. 6:37 PM

adding ice/water shield adhesive backed roofing membrane to the inner surfaces will add mass, stiffness and damping---,I have used it to great effect on various speaker.quick and easy and very dense.

askthecableguy diz: Abr 20, 2014. 6:19 PM
great idea. Do you have any vibration issues with using gas cans. what else you use if the gas cans didn't come to you?
captainserious diz: Abr 18, 2014. 4:09 PM

These are great looking. Add a battery in one and the amp in the other and go mobile!

iamunique127 diz: Abr 10, 2014. 5:59 AM

Great idea. These will make great portable speakers. I'm thinking if I include an amp with an AUX plug I can then plug my iPod into it.


longp2000 diz: Abr 9, 2014. 8:31 PM

Genius, Genius, Genius

muddog15 diz: Abr 9, 2014. 5:45 PM
Gonna make one for bass guitar.
sedmonds diz: Abr 9, 2014. 10:37 AM

So how do you power the amp?

Vinsu diz: Abr 9, 2014. 10:10 AM

Great idea! Maybe you could add bass response and general sturdiness by laminating some fiberglass inside the boxes. That would also decrease the plastic-kind-of-sound you may be experiencing without adding too much weight.

Here's an excellent instructable about fiberglass that could make your great speakers even more awesome!

josefski diz: Abr 19, 2014. 10:54 PM

I was thinking the same thing! They'd sound super duper awesome with something to dampen the insides and make the acoustic chamber more rigid.

kbc2 diz: Abr 8, 2014. 6:30 PM
Realy dig the idea, my attempt a pair of my own. One suggestion, for the mounting holes of the woofer, use the clip on nuts that are used in cars , also found at home depot.
vladivastok diz: Abr 8, 2014. 3:26 PM


kzint diz: Abr 8, 2014. 3:14 PM
Dude, bottom line: this is such a neat idea! My hat is off to ya. I love the way the tweeters sit on that angular part of the can. And as far as the "audiophiles" are concerned, they are gas cans! If it is about trying to achieve perfect tonal quality, I would recommend another medium! Rock on!
trcky1 diz: Abr 8, 2014. 12:48 PM

Good idea! I wonder if a little spray foam inside would deaden the rattle that that thin wall plastic is going to produce?

Dr.+Science diz: Abr 8, 2014. 11:40 AM

I tried the same trick with some styrofoam "cooler" boxes, the kind they ship meds that needs to stay cold via FedEx and they worked pretty good too.

Tex+Arcana diz: Abr 8, 2014. 6:36 PM
My neighbor across the street builds these for fun, full-featured, and AC/DC power.
Tarun+Upadhyaya diz: Abr 8, 2014. 7:09 AM

Wow...that is a powerhouse project :)

thankyousam diz: Abr 8, 2014. 6:51 AM

I don't usually feel the need to leave a comment, but I had to for this as I really like the idea and the execution. I just wish I had a need to make some for myself :)

Kenno79 diz: Abr 8, 2014. 3:16 PM

I feel the same way. The looks of these speakers caught my attention. The look awesome and the handle makes them so practical. I really wish I had the need to make a set myself. Well someday in the future when I own a house with a cool garage. But thumbs up for a cool project :)

bob3030 diz: Abr 7, 2014. 9:45 PM
Very cool. Great look for a garage audio system. Thanks for posting.
rnalawansa diz: Abr 7, 2014. 7:27 PM
Cool project. How do they sound? Plastic usually isn't the best for speaker housings
Tex+Arcana diz: Abr 8, 2014. 6:35 PM
Could spray on some cyanoacrilate foam inside to stiffen the plastic and insulate the enclosures.
Mrballeng diz: Abr 7, 2014. 7:14 PM

High octane awesome.

You213 diz: Abr 7, 2014. 5:48 PM
very creative but probably not the best sounding(:
CraigRJess diz: Abr 7, 2014. 5:10 PM


Dont forget the speaker grill to protect it.

Misac-kun diz: Abr 7, 2014. 5:09 PM

Gonna make a piar of these for my future shows

M3G diz: Abr 7, 2014. 4:38 PM

Very cool!

Danger+is+my+middle+name diz: Abr 7, 2014. 3:38 PM

Nice, I like that the handles on the gas cans makes them easy to carry!

jbackes diz: Abr 7, 2014. 11:48 AM

Very nice!