Introduction: Reworking Isntructable

--

Step 1:

Comments

author
DonovanS11 (author)2016-08-12

Will this ever be reposted? I saw a video of someone who built it and I would like to see the plans in more detail.

author
george17 (author)2015-01-29

hey kbcford1 when do you think that they instructable will be done reworking because i made it last april and i want to make a smaller version out of brass

author
jermain.fishwick (author)2014-10-11

can anyone tell me how to see the instructions , it`s under construction plzzzzz i want to make it

author
omnistructable (author)2014-04-23

For those who cannot see the instructable download the pdf.

author

what is the pdf???????????

author
george17 (author)2014-09-22

I made the Hardware Store Steam Engine over April break last spring very good instructable Thanks Kyle

author
triple5timer (author)2014-05-05

Hey kyle, or anyone who finished, i was wondering how the gas makes it from the inlet tubes to the pivot arm and then to the cylinder.

author
Penolopy Bulnick (author)2014-04-24

Hi,

I've unpublished your Instructable while you make your changes. You can find it in your Drafts and go ahead and publish it again when you are good to go!

Best,
Nicole
Community Support Manager

author

Thank you Nicole! I hope to be done reworking all of my instructables soon!

Kyle

author
triple5timer (author)2014-04-14

Hey myakka, could you at least post a schematic. It looks like the page expired.

author

Download the pdf

author

Sorry, when i said piston housing i meant cylinder. What kind of loose joint does that have?

author
kcbford1 (author)2011-03-04

FYI, i had a busy week! i will be on sometime this weekend to answer some of the questions that were asked this week. Thanks!

author
triple5timer (author)kcbford12014-04-16

Come on man, why has the page disappeared? You should create a video to replace it or even a comment. It is really cool.

author
chris.klim (author)kcbford12012-12-03

Fantastic design. I think I will build this over the weekend.
only one question- where is the escape valve?

author
triple5timer (author)2014-04-16

Please, would anyone who remembers the page before it disappeared tell me how the piston housing is able to move.

author
ElectricBuilder (author)2014-04-08

Hi,

Will increasing the size of cylinder and piston increase the speed and power of engine?

author

it will increase power but if anything decrease the speed. Also can you see this instructables because nothing is showing up for me?

author
triple5timer (author)2014-04-13

why has the page disappeared?

author
coleemslie (author)triple5timer2014-04-13

it's happened to me right after I bought the supplies and I am pissed

author
myakka (author)2012-02-25

here is my design i just finished. it is a vertical compact design that would be easier to use for making moving models like a boat or something. all the stuff needed for this can be bought at the hardware store just like kcbford1's.
im way to obsessed with this instructable.

steam engine 004.jpgsteam engine 002.jpg
author
coleemslie (author)myakka2014-04-07

I'm just wondering if that us a 2 inch caster wheel. Please email the reply to emslicol000@isd284.com or text me at 763 478 1303

author
joaquinakiwi (author)2013-01-04

Where does the steam come from? Do you have to pump hot water/ steam into the engine or could you out some sort of heat source under the tank?

author

You put water into a boiler, and have a heat source under it. For this, you can use basic sterno from the grocery store, or denatured alcohol available at any hard ware store. and you can make a boiler from a empty spray can, or a propane tank used for soldering. PLEASE NOTE, that it is always a good idea to put a SAFTEY VALVE on any steam boiler, you can buy them from companies like "Ministeam.com" who sell model steam engines and model steam engine parts, hope this helps. Any questions please feel free to message me. P.C.

author
turtledrake (author)2013-09-02

Yes. If you take a tube the correct size and fill it with epoxy it will work

author
You213 (author)2011-07-07

I am going to combine this with the desktop steam boiler and make an R/C car !

author
Dustinstroh (author)You2132011-11-05

Have you completed this yet? I am in the middle of combining these two projects aswell. I have the boiler complete, now to move on to this engine!

author
You213 (author)Dustinstroh2013-07-07

hey just wondering if you have completed this? I stopped building it because it became impractical and a lot of work

author
usafbrat (author)2013-06-27

Cool

author
Angrierbeaver (author)2013-05-05

was wondering if copper pipe and piston diameter can be increased? And if so does the safety ratio go down when powered by steam?

author
synapser (author)2013-02-03

Do you remember by chance how much this total project costs to construct?

author
joaquinakiwi (author)2013-01-04

Also, how might I hook it up to a toy car or something to power it?

author
tremblay.eti (author)2012-07-05

What if the steam cools down below the boiling point before exiting the cylinder?Could there be water accumulation and how would that affect the engine?

Very clever design by the way!

author
Orchestrapit (author)2012-04-18

with the right alternator/generator combined with a buffer battery, this engine should generate more than enough power ( but not too much more) to charge a smart phone, it just depends on the coil dimensions of the alternator/generator and the rpm of the motor.

author

actually, since it's low current, you could probably use a dc motor as a generator, just make a battery charging circuit.

author
TheWilks1 (author)2012-01-30

Could you make this out of PVC piping?

author
Orchestrapit (author)TheWilks12012-04-18

only if you planned to use compressed air, to power it. if you wanted to use steam, you would need to use metal tubing.

author
gemhund (author)2011-12-27

Here is one I just finished, made out of glass.

http://youtu.be/c2TAccSxQJk.

I put a sequence on my blog.

http://hansmeevis.blogspot.com/

For what it's worth......

author
TheWilks1 (author)gemhund2012-01-30

Do you have a how to video?

author
gemhund (author)TheWilks12012-01-30

Unfortunately no. I do tutorials with photo's but this one was just a prelude to figuring how to build a steam machine out of gem stone.
Check out http://youtu.be/HhAkS0vWsEo
And just for interest sake, I put up a tut on my blog yesterday, unrelated to engines but concerning jewellery .
http://hansmeevis.blogspot.com/
I have a lot on my website http://meevis.com/jewelry-making-class-list.htm
Nevertheless, It was your original tut that started all this (grin)
My wife has been heard muttering things like second childhood and senile...etc.
Cheers, Hans.

author
The steam engineer (author)2012-01-21

Do you think it is possible to make the pipes 2 inches and increase the power. I am trying to build a steam locomotive and am hoping this piston will work... Thanks

author
costiecam (author)2012-01-10

This looks like a fun build! Looking to build this week/weekend. Quick question, how far apart are the flywheel stand posts and the cylinder pibot stand posts. I saw you had center lines drwand on the base board between the two. If i could just get the distance between the lines that would be awsome. Thanks.

author
Dustinstroh (author)2011-11-05

How many PSI does this engine require to run?

author
myakka (author)Dustinstroh2012-01-07

i run 20 or 30 but its fast

author
kdinh2 (author)2011-11-06

where can i buy the 1/2 repair coupling 12" long ? i been go to grainger ,plumbing ,true value supply and they show me the 1" long repair coupling. can you let me know where to get this coupling

author
VictrolaGuy (author)kdinh22011-12-24

Most Lowe's stores still carry the 12" long repair couplings.

author
gemhund (author)2011-12-01

Hi Kyle,
I just finished a machine based on your instructions. Thanks, very cool and very well done. I had been looking around for something like that and yours fited the bill perfectly. I posted a video of it running on you tube http://www.youtube.com/watch?v=nmRI4YB7VCA My user name is gemhund. Thanks again,
Hans

author
carfur (author)2011-09-29

i can't get my hands on ½ brass test plug.Can you please tell me what else can i use for the piston?Or how to mold something simmilar.
@myakka:if you soldered it right it shoud hold up pretty good.I made my flywheel from a nut and 6 bolts and tested it with a drilling tool and it remained intact during and after the spinning.

author
myakka (author)carfur2011-10-02

Just use a 1/2" steel rod from tractor supply co. As long as you oil the engine and remove it after running then im sure it wont rust.

Btw: you solderd six bolts to a nut? I realy hope those dont break off... Or even 1 of them ... It wold shake itself to peices

author
carfur (author)myakka2011-10-03

I soldered bolts to a nut because its the best way to balance the flywheel and the crank by adding nuts on the bolt that needs more weight.Its just a beta version until i complete my spotwelder.I plan to make a v4 from this concept.Im concerned that the steel rod will be to heavy and it will run slow.For the moment i rolled pvc insulation tape and it holds up pretty well for the piston.I think i will use the steel rod as the endcap.I also discovered that hotglue vs steam isnt a good ideea(ruined my first motor with it).