Picture of Hardwood floor|standing speakers
Did you end up with a spare box of scrap hardwood flooring?
Make a set of floor standing speakers with it!

Skill level
Intermediate - advanced woodworking

Scrap hardwood
Speaker components.
Assorted wood screws - #6 or #8
Paint (optional)
Packaging foam
Wood glue
Liquid nails

Drill & bits
Remove these adsRemove these ads by Signing Up

Step 1: Layout materials

Picture of Layout materials
Have your speakers ready to check sizing.
Match wood grains if possible.
Stagger the pieces to give the joints more strength.

Step 2: Glue pieces together

Picture of Glue pieces together
Using wood glue and clamps glue pieces together.
Set them aside to dry.
Stack them on a flat level surface.

Step 3: Remove flooring nails

Picture of Remove flooring nails
EDIT P1130220.jpg
If your scrap pieces have nails or screws now is the time to remove them now.

Step 4: Cut to size

Picture of Cut to size
Cut all the pieces to size.
(Speaker components will vary, so measure twice cut once)

Step 5: Choose a wood joining method

Picture of Choose a wood joining method
EDIT P1130228.jpg
There are many types of wood joining techniques.

I went with a dado wood joint.
It was the least time consuming, and stronger than a lap joint.

Apply the joints to the edges.

Step 6: Determine speaker configuration

Picture of Determine speaker configuration
Depending on the speaker components you buy, the manufacturer will suggest the layout.
Here I'm using a tmm setup. (Tweeter/Mid/Mid)

Step 7: Cutting holes for speaker mounting

Picture of Cutting holes for speaker mounting
EDIT P1130253.jpg
EDIT P1130254.jpg
EDIT P1130258.jpg
EDIT P1130285.jpg
The easiest way to cut circles is with a plunge router and circle template.
I scored an open box plunge router for $30 bucks.
The circle template I had to make.

Find a scrap piece of clear acrylic.
Copy hole set of the plastic base plate onto the scrap piece of acrylic.
Drill out holes.

Pic 2
Temporarily mount the template (Scrap acrylic piece) onto a working surface

Pic 3
Using a compass and a ruler, mark your lengths from the center point of the router.
(This will be the center of your router.)
Drill location holes at the marked length... this will be the pivoting/spinning point for the router

Pic 4
Mount the new acrylic template onto the router.

Pic 5
Cut a test piece.
The pivot/spinning hole rests in a screw placed in the center of your workpiece
As you are cutting all the way through, be sure to have scrap material to raise your piece so you don't cut into your bench

LordRussell3 years ago
My only problem with Trans Line assemblies is if done 'wrong' will rob your cabinets of their low end frequencies faster than a starved lioness fires through a bucket of fattened hamsters.

Your design here is elegant as well as functional, but you're not immediately showing the 1/2 to 1/4 rule in your step down (or the basic 'angular' thought) behind the Trans Line construction. Your measurements seem to follow the guidelines, but I was always led to believe the construction was to be at some kind of angle.

Hey, that's what thinking 'out of the box' is all about right?
tubegeek3 years ago
Certainly there are many places on the net to discuss and learn about subjects like speaker volume, T-line length, stuffing, crossovers etc. What I found VERY unique and valuable about this 'ible is that the fairly straightforward construction method results in such a good-looking enclosure. For me, I would do this process AFTER I had developed a design that I had decided was worth boxing up nicely. I am very glad to see how hells-oui did it. This is a very good home-workshop-style alternative to more typical methods like birch ply & stain, or MDF & veneer, with a similarly attractive result and, I think, more options for fancy wood choice and colors. Let's face it, putting down a good durable finish is difficult and time-consuming, that's the whole reason pre-finished flooring exists.

I wouldn't worry at all about the hardwood being resonant in this design, note that both front & back walls are MDF, and note that the T-line parts will VERY securely brace the hardwood sides.

Excellent 'ible providing MUCH food for thought, thank you very much hells-oui.
hogey743 years ago
Nice article thanks! I've got some old monitors that sound great but the particle board is particle-izing ... ur giving me ideas :-)
danzo3213 years ago
SMART to use this heavy flooring which has a supertough finish already. But first step ought to be: design the speaker boxes.
danzo3213 years ago
Ideally this design features a constantly tapering cross section [folded horn] which will drive you nuts with the angles! But just note the two woofers are not equally spaced from the gap, so right there you have a slight time differential. In other words: the 2 woofers move up + down in unison but face unequal box pressure.
danzo3213 years ago
Veryken is right, the internal volume has to agree with the suspension stiffness and size of the speaker cone. As it travels from farthest down to farthest up it moves a measurable qty of air and the air in the box acts as a spring. Speaker manufacturers should give this measurement as "Q" and there are formulas to use. Ported enclosures have their own formulas.
With an open attic as your box, you have what is called an infinite baffle, and must use a really stiff woofer.
Bose has made a small fortune by perfecting this type of technology in their "acoustic waveguide" technology speakers. We need more innovators in this world.
veryken3 years ago
Looks great! Aside from the "acoustic transmission line" that you mention, what determines the box size? I thought speaker design was all about the internal volume -- width, depth, resonant surfaces, even solidity. I'm not criticizing, but I did a similar box mount for a ceiling situation with an open attic. The sound that resulted were not that good.
bigdawgte3 years ago
did you use any formula/calculator, etc. to design your transmission line? Or did you just wing it?
Boost3 years ago
They are really nice looking! How do they sound?

I would be afraid that solid wood would make it a resonance box giving it a "boxy" sound. I have always strived to get a dead box (as in non vibrating and sound conducting) in my speaker cabinets.
hells-oui (author)  Boost3 years ago
They're not too bad, no boxy sound.
The hardwood was santos mahogany.
It has a density similar to mdf.
So I thought... why not.