Instructables
Picture of Hemma Light Chandelier Hack
Building off of an instructable by "edwinston14" and a suggestion by "piaferre" I created this custom chandelier for our dining room.  It was relatively cheap.  Got it all done for less than $100 with parts from Ikea, Lowes and a local Lighting/Fan store. 

SUPPLIES:

-10 Hemma Lights
-10 Air Gap Caps (used to cover the Hemma fixture and hide the threading)
-10 Washers
-10 Eye Hooks
-10 Drywall Anchors (optional)
-Cover (from a lighting & fan store)
-10 Light bulbs
-2 Large Electrical Wire Nuts
-Plastic Cable Ties
-Glue

TOOLS:

-Wire Cutters
-Sanding tool (Dremel or Mouse Sander or Metal File)
-Drill with large bit
-Electrical Wire cutter/stripper

 
Remove these adsRemove these ads by Signing Up

Step 1: Stretch out Hemma cords

Picture of Stretch out Hemma cords
Step 1:  Open all Hemma lights and stretch out cords to remove kinks (best done overnight)

Step 2:  Cut all plugs off of Hemma lights

Step 2: Prep fixture covers

Picture of Prep fixture covers
Step 3:  Drill hole on top of Air Gap Cap to thread wire from Hemma fixture through (repeat for all fixtures)

Step 4:  Using wire cutters and sanders, grid down threading on Hemma fixture so that Air Gap Cap can slide over and cover the threading of the fixture (repeat for all fixtures)

Step 5:  Remove Air Gap Caps from all fixtures

Step 3: Paint parts

Picture of Paint parts
Step 6:  Spray paint all Air Gap Caps (inside and outside), Washers, Eye Hooks and Cover with black paint 

Step 4: Prep ceiling

Picture of Prep ceiling
Step 7:  Mark off all points on ceiling where you want to attach Eye Hooks.  If necessary, insert drywall anchors at marked points 

Step 5: Install hooks and thread fixtures

Picture of Install hooks and thread fixtures
 Step 8:  Insert Eye Hook through Washer.  Apply glue to washer so that it is glued flush to the ceiling when Eye Hook is screwed in.  Screw in Eye Hooks to marked points.  (repeat for all washers and hooks)

Step 9:  Install all painted Air Gap Covers over the Hemma Fixtures

Step 10:  Thread wire through Eye Hook so fixtures hang at desired height.  Remember to account for additional length of light bulb when setting length.  (repeat for all fixtures

I really like your design! You mentioned a step in there to straighten the cords...if you heat them with a heat gun while they are stretched (perhaps with a weight attached to the end), before assembly, I believe you'll find that they will remain much straighter. This method has worked for me in the past.

marydecorator8 months ago

Gorgeous! Which size are those washers?

coozerlv (author)  marydecorator8 months ago
Thanks. The diameter of the washer was 1.5". The inner diameter of the hole in the washer was the same size as the thread on the eye hook screw.
TXTCLA551 year ago
off topic, but what is on those square pictures on the wall?
khaines2 years ago
It would be fairly easy (though a bit time consuming) to feed the cords through some chainmaille. Might add a nice touch :)
mmestre3 years ago
Sweet! Thank you! I will post pics of my twist on your idea as soon as it's ready. Again, thank you!
sanewby3 years ago
here is the Edison Chandelier that someone mentioned above...

http://www.potterybarn.com/products/edison-chandelier/
samandjan4 years ago
looks very similar to the $400 Pottery Barn "Edison Chandelier".  very cool, thanks
beccane4 years ago
 This is great but i live in an oooold building. Do i need to be careful what wattage bulbs I use?
coozerlv (author)  beccane4 years ago
 I am not an electrician so I can't really comment on this.  Sorry.
clarkt coozerlv4 years ago
You will want to be mindful of the wattage, especially with an older electrical system.

P(watts) = Voltage (v) * Current (I)
therefore,, I = V/W
                   I = 120 / 40
                    = .333 Amps per bulb 
Times 10 bulbs = 3 1/ 3 amps.   This is for 40 Watt bulbs. 

60 Watt bulbs would draw 1/2 amp per bulb, or 5 amps total. 

However , with 10 bulbs, I am betting that 40 or even smaller would do nicely.  
clarkt clarkt4 years ago
And oh yeah, it looks cool too.   

Nice work
coozerlv (author)  clarkt4 years ago
 Thanks much for the comments.  Before I installed this light I had this really dim thing from Lowes that I hated.  I had installed a dimmer from the get go because this really puts out a lot of light but because the room is so open it's not actually as bright as it seems.  

I also tried it using frosted bulbs but wasn't as nice looking and I tried the bulbs that are metallic opaque on the bottom half but those did not put out enough light.

With a fixture like this over a dining room table, I would suggest 15 watt incandescent bulbs on a dimmer switch. You really do not want to light up a dining room table for a meal too much, it is better to keep the environment more intimate with lower levels of light.
I agree.   Even 40 watt bulbs would put out a tremendous amount of light in quantities of 10.  However there may be a need for such light at times.    And as long as you are adding a dimmer, you can always cut the 40s down to a dim glow.   Then when you are at the table building your next instructible project, you may want all the light those bulbs can muster.  


cloudyerout4 years ago
This looks SOOOOO cool
Doctor What4 years ago
 Cute!  If you took some small black chain link (or get some chains regular chains and spray paint them black) and fed the wires through it, it would remove the "wire look".  

It's a simple fix.  A quick look at lowes.com shows 10 feet for about 10 bucks.  I'm sure you could find chain for less though.

This is a gorgeous idea.

www.lowes.com/pd_47623-273-5973000_4294934403_

I like your idea, but I would suggest the use of plastic chain that can be found at most hardware stores or big box home improvement stores. The plastic chain would help achieve your desired look, but would also be a lot lighter, putting less strain on the wires.
centrd4 years ago
This is awesome. Perfect for the current industrial trend in chandeliers. And at a fraction of the cost! Thank you!
piaferre4 years ago
geniall
bobtannica4 years ago
Very neat instructable. Thanks for putting it up. One question... what is a hemma light? I tried googling it and all I discovered is that you can buy them at Ikea. Doesn't really state what it is?!?!? Anyway, thanks again but I would love a definition.
coozerlv (author)  bobtannica4 years ago
 A Hemma light is basically a light fixture that has a 15 foot cord, a standard plug on one end and a standard light bulb plug on the other.  At Ikea the cord is intended to be run up a wall from the outlet then hung from the ceiling using the included plastic mounting clip.  They also have a number of lamp shade styles to go with it at Ikea.
Thanks! Again, very neat instructable!
coozerlv (author) 4 years ago
 Thanks for all the feedback.  Glad you all liked it!
monniemoo4 years ago
 gorgeous!
! xD !4 years ago
Although I think putting shades on them might help, I really like the design! Kinda reminds me of the City of Ember...
luvit4 years ago
 if i press on my eyes for a minute, then open them, i get the same effect.