Instructables
This is a full size(4ftx8ft) one person hovercraft built over one summer for less than $200. It was built with no prior experience or knowledge of hovercrafts but with sheer determination to build something different. So check this project out, hope you like it.

Disclaimer (March 2013): I have not made any changes to this Instructable since the early days of this website, 2006.  Take this Instructable as an example of how not to build a Hovercraft.  The homemade thrust fan and unshielded rotating parts make this homemade craft pretty dangerous.  If your building a hovercraft of your own please consider the safety aspects large rotating parts and apply this understanding in your design.  For a great example of how to build a working and safe hovercraft see this Instrucable 10-HP-Hovercraft  
 
Remove these adsRemove these ads by Signing Up

Step 1: The Skirt and Base

Lets start out with a little history, I built the hover craft during the summer between my sophomore and junior years of high school. It was built by a good friend, Brain, and myself Doug. Like I said I built the entire craft for less $200 including the engines and the fans. I will explain how I did it soon but lets start out some of the main things you will need to get started.

3hp Horizontal Shaft Engine $50 at a local lawnmower repair shop
4hp Vertical Shaft engine took it off one of my lawnmowers
5.2 moisture resistant Lauan Plywood 4ftx8ft
Styrofoam 4ftx8ft
1/2in Plywood 2ftx4ft
A couple 2x4 8ft
A couple 1x2 8ft
1/4in bolts and nuts 1in- 3in
Wood Screws 1/2in - 1in
Plastic sheeting Painters Sheet (this is the skirt material)
Brass Grommets with punch You can get this as a kit

This is about what I started out with but in no way is this everything youll need. Also keep in mind that this is how I did it, if you plan on taking on a project like this do it how you want to and with what is available to you. Use this as a guide so that you do not make the same mistakes I did.

Lets start out from the ground up. On a hovercraft the only thing that touches the ground is the skirt. The skirt is the part of the hovercraft that holds air to lift the craft. Like in the second picture my hovercraft has two engines, one for lift and one for thrust. The lift engine pushes air under the craft and the skirt holds the air in. As more air is pushed under the craft pressure builds up and lifts the hovercraft off the ground. This is how a hovercraft hovers, the only thing in between the base of the craft and the ground is air.

But before I designed the skirt I designed the base of the craft. It has to be light(this is the most important) and it has to be strong enough to hold the weight of a person and the engines and everything else. Keep in mind though that when hovering the craft is actually more stable than when its not. The air pressure helps to hold the weight evenly over the entire craft.

This said here is how I made the base. I got two sheets of 4ftx8ft lauan and a piece of 2in thick Styrofoam. The lauan was the cheapest and the lightest sheet of plywood I could find at home depot. One note, I got almost everything for this hovercraft at home depot. Lows or any hardware store will probably have the same items I got.

The base is just the two sheets of plywood with the Styrofoam sandwiched in between. Holes are drilled all the way through this sandwich and bolts are used to hold all of the components on the base.

Back to the skirt which is one of the more trickier parts of a hovercraft. It has to hold its shape under pressure and it has to be the right size. To big and it will drag on the ground which will slow the craft down or not let it move at all and to small and it will not hold enough air to sustain lift.

To overcome this I designed my skirt to have 8 different pieces that I sewed all together with nylon string. For each of the four sides of the craft there are two skirt pieces. A upper half and a lower half, which are same shape. The picture shows what each part looked like. Basically the same design for all four sides just different lengths. The skirt is actually smaller than 4ftx8ft by 2in on all sides. This is done so that the skirt can sandwich between the Styrofoam and the top piece of plywood. So you will need four longer skirt pieces and four shorter ones.
Each piece first needs its flap folded over and sewn. To sew the skirt I used a standard sewing machine and sewed along the seam lines which are 1/2in from the edge. Now take two pieces one short and one long and sew them together at the angled end. Now do this again for all the other pieces to form a two rectangles. Now put one rectangle on top of the other and sew along the outside perimeter. This forms the whole skirt but its not done yet.

Now duck tape along the seam for added strength then flip the skirt inside out so the seams are in the inside. Punch holes on the inside of the skirt in the middle of the flap on the top and the bottom of the skirt with the grommet kit. Put holes on all corners and every foot along the length of each side. Drill holes through the base that line up with the grommets. Sandwich the top of the skirt between the Styrofoam and the top piece of plywood and then use 1/4in bolts to hold it all together.

This completes the skirt and the base. This is the most general part of the build. The rest of the craft is built specific to the engines, fans and components I used, you will have to adapt these plans to fit your components.

Sorry about the pictures I could not get them to show up very well. I included the DWG file though. The last picture is the overall skirt put together showing the flap folded over with the dashed line and where holes should be put with the circles.
hovercraftorg5 months ago
Lawn mower blades are very dangerous, we use the same fan blades as used in air conditioners pitched at about 37.5 degrees. It is important to add proper fan guards front and rear - hovercraft racers don't like doing this as it slows air thru the duct, but there was a fatality in NZ, someone lost a few fingers in Australia last year - if you want your kids to play guitar or piano, make sure you fit proper guards.
weargle11 months ago
i couldnt get a fan so i made one using the lawn mower blades by bending them
KrystianEly12 months ago
i have a prodject in college where we have to use the information over the 2 years to build something, everyone chose a go-cart but i chose a hover craft im building this on my own, do you think it will be worse if i was to add slightly bigger engins? thanks.
pavilion891 year ago
My craft is about 8 icnh height, 8feet length, 4 feet wide and capacity for a person only. is 2.8hp enough ?
dbc1218 (author)  pavilion891 year ago
I don't think that will be enough unless the craft is very light. check out this http://www.instructables.com/id/10-HP-Hovercraft/ same size but uses a 10hp engine
pavilion891 year ago
what is the suitable material to built a fan for engine of 2.8hp?
dbc1218 (author)  pavilion891 year ago
I would not recommend building your own fan, especially not like the steel fan I built for this craft. Most fans/props I've seen are made from wood or have plastic baldes connected to a center metal hub. Also, if your building a craft similar in size to mine, 2.8hp won't be enough power.
Wonder if you could make two smaller almost hoverboards connect them to make a hover "pontoon boat" or catmeran
Dovim5 years ago
hey, awesome guide. i have a couple questions though. how fast can it go? can you make it have more surface area while using the same skirt and engine setup? and i thought of a way in which the forwards thrust fan might be replaced by a spinning wheel which could be lowered and maneuvered like that of a motorboat (i don't know very well how to explain it). thanks
dbc1218 (author)  Dovim5 years ago
It didn't really go anywhere, read the last step. Why would you want to make it bigger? If you did make it bigger with engines similar to mine, it would be way underpowered and probably not hover. An outboard wheel could work but I think it would defeat the purpose of a "Hover"craft
Dovim dbc12185 years ago
Ah, i see. so it was too heavy for the fan to actually accelerate it, right? well, an outboard wheel would solve that problem, i think. also, i see the purpose of a hovercraft as a vehicle that can go on land and water, so if the outboard wheel could also be used as a fan in the water, then the purpose would be complete. also, an addition of an outboard wheel would lead to the only speed limit being air resistance, since it doesn't touch the ground (as different to all other vehicles), whereas the wheel could be lifted so it didn't touch the ground. the result is it could just keep accelerating and accelerating. The results could be interesting. The thing about making it bigger was merely curiosity, though. i can see that it would have no practical purpose, and if i could make it smaller without losing stability, then it contributes to making it lighter, thus faster. As i said, the results could be interesting. i'll have to do a lot of thinking on it, but the hovering mechanism of your hovercraft seems like a great way to start.
double_g Dovim5 years ago
I'm not sure if this is true as I'm rather new to the hovercraft scene, but from what I've read it seems that increasing the area actually increases the lift generated. I'm not sure where the page was that said this but if you crunch some numbers on the following website you'll find that this seems to be true. http://www.olshove.com/HoverHome/hovcalc.html
If someone can explain this it would be much appreciated, since I haven't yet figured it out (I'll ponder on it a bit more in the meantime and see if I can come up with a logical explanation).

Of course weight to lift gain must be considered.

-hope this helps future builders

Double_G
dbc1218 (author)  double_g5 years ago
If you increase the size of the craft and therefore the area the pressure needed to maintain lift will decrease but the amount of air needed to be forced under the craft will increase. This usually means you have to use a different fan or a more powerful lift engine. During the design of the craft you have to decide what you want. If you want a bigger hovercraft you need to match that with the right size engine and lift fan, but if you already have the engine size set then you need to decide on the right size craft. The guy that created that site from your link says he used Hovercrafting As A Hobby to create the calculator so I would start there.
Thanks I built my hovercraft for my high school senior project. I've planned on making a bigger better version so I'll definitely take your advice for that if I ever get back around to it. Alas plans for the new version are in a long list of projects not the smallest of which being my senior project for my undergrad in electrical engineering.
Pfarmkid1 year ago
how did you make the steering controls?
You could build your own fans from wood, all you would have to do is check out Universal Hovercraft with a search. I have built a hovercraft from plans that I got from them. turned out to be a very versital craft.Mine was 6ft x 12 ft and had a 5 hp lift motor and a 30inch home made lift fan and 2-5 hp thrust motors with 48inch homemade thrust fans. I now have plans for a little bigger craft for exploring. You should really check out :Universal Hovercraft, they are based in Cordova Illinois. A very good place to start a hovercraft adventure.They have plans,supplies and advice/tutorails for hovercraft builders.Great ible though
How much did it cost?
PickPacket5 years ago
That looks safe..
THIS IS IN NO WAY SAFE. For our cadet's "Pioneer's" platoon (building stuff), we built 3 full sized hovercrafts for use. The prototype on it's first run tore itself apart, srapel flying everywhere, nearly killing myself and many other cadets. In building these hovercrafts, ensure that there is a metal mesh over the air intake (and outakes) and that the propellers are insulated in metal. Depending on your propller speed. Have fire equipment ready. Being 14, I don't want me or my cadets to die.
What branch JROTC are you? I am army JROTC.
By the way... The same thing happened about a month later. With the metal, the propeller stayed in the engine housing, causing only damage to the engine, housing and propeller. The hovercraft remained floating, while we remove the two year seven cadets from the craft, set up a perimeter, and killed the engine. The craft didn't even sink! MUCH SAFER.
Does anyone think it's possible to make it hover a few FEET off the ground?
they're called hoverwings, google it
I ment without wings.
Then no, it's not possible, the skirt has to be touching the ground to maintain the air cushion. but you can still hit jumps with a sturdy hovercraft. Look up hoverwings though, they're cool.
dbc1218 (author)  jbowman72 years ago
Large hovercraft, like the ones the military use, hover a few feet off the ground but that height is sort of proportional to the their size. A small hover craft that hovered that high would most likely by unstable, remember your sitting on air, so nothing but your balance will keep you upright.
Not sure if even they hover that high actually, maybe periodically though
geckomage2 years ago
will this hold a 260 lb person like myself? :P i normally go muddin in my truck when i wana have fun driving something. but this'd be fun :D
gopalrr3 years ago
hi,

can you share details of how you did the 70%/30% distribution of air thrust to lifting and propulsion ?

gopalrr
dbc1218 (author)  gopalrr2 years ago
that distribution is typical of a hover craft that uses a single engine to turn one ducted prop. the duct is split to divert 30% of the air underneath the craft for lift and the rest for thrust. My hover creaft used two engines and fans so that distribution is different
rocketman202 years ago
Where did you get the fan you used for trust.
dbc1218 (author)  rocketman202 years ago
I made it from sheet metal and angle iron, but I would not recommend doing this at all. Get a purpose made prop thats been properly balanced.
elina02 years ago
OMG! This seems me too heavy..
rbland2 years ago
you probably want to put some sort of cage around the vents too: http://www.stuff.co.nz/national/5380361/Auckland-man-decapitated-testing-hovercraft
rocketman202 years ago
Are the Brass Grommets just for attaching the skirt to the base? Also does the skirt have holes in it? I am trying to build a hovercraft myself but am having a hard time understanding how the skirt works.
dbc1218 (author)  rocketman202 years ago
they are just for attaching the bottom edge of the skirt to the base with small rope
jdhover2 years ago
so is your base piece hollow or is it ducted?
dbc1218 (author)  jdhover2 years ago
its a sandwich of t pieces of 1/4" plywood with 2" of Styrofoam in between
.
nibbler1253 years ago
you need a real fan that metal one has no airfoil and you could easy double youre lift with a good wood one it will cost allot more tho up to 200$
or just make one yourself, assuming of course you have basic air foil knowledge and the ability to carve
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!