loading

Step 2: Cutting the Wood

Adjust the Table Saw guide to 1.5" width and cut the 36" length of wood. Mark the wood from one end to taper approximately 7/8" to the top end 1.5". Proceed to the next step to drill the dowel hole before cutting this off.

(Note: The safety cover has been removed for photography purposes.)

Honestly, this is the best tutorial I've come across on instructables thus far. I am amazed at how precisely you described each step. I think when I make my cane in the near future, I'm going to try to do it all by hand. I want to see if I can do it how my great great great grandfather did it. His cane has lasted over a hundred years and is still in perfect condition. Thanks for the wonderful instructable.
first time using this website. this was extremely helpful
<p>Could you post an Instructable on getting an even taper with spokeshaves? That's a surprisingly-difficult operation to find good videos or instruction on.</p>
<p>Very nice looking cane. What a great tutorial. I have been making chess boards and cutting boards out of exotic woods lately. I think I will have to give this project a try. Should be easy enough. Thank you my friend. </p>
<p>Wow I never knew there were good and bad ways to make a walking cane. Being able to make your own custom walking cane seems like it would be a lot of fun to do. I have a grandfather who collects canes and this might be something he would like. http://www.dmepromed.com/products-services.htm</p>
<p>This was a fantastic instructable! I just finished one for my dad who recently had two knee surgeries. He'll love it.</p><p>I used cherry for the shaft, mesquite for the handle, and a wenge collar. I used teak oil to protect it all and applied couple of coats of wood wax to give it a slight sheen and to smooth the irregularities out of the wood.</p><p>Request: If you make another one in the future, can you please demonstrate the tools you used to make the handle and how you shaped it in more detail? Thanks!</p>
<p>the handle would be shaped with a variety of rasps, files, and sanding sticks, starting with the most coarse tool to quickly rough out the shape, and going progressively finer as it approaches the desired form, finishing with a fine wet/dry sandpaper to smooth away any tool marks. you could also use chisels or wood carving knives, whatever was available and that you were comfortable with</p>
<p>Ooops! I meant to put 90 degrees. When in doubt, look at the photo! Thanks for the flag.</p>
<p>Can you elaborate a bit on this step? What do you mean when you say &quot;clamp the shaft so the surface is 45 degrees square from the drill shaft&quot; ? It looks like you are drilling straight down (90 degrees) </p>
I made a walking stick out of a broken shovel handle. Carved a morel mushroom on the end. Fancied it up with a plumber's torch and finished it with poly. Most big tool handles used to be made with ash or hickory. Good woods for canes and walking sticks.
I made a walking stick out of a broken shovel handle. Carved a morel mushroom on the end. Fancied it up with a plumber's torch and finished it with poly. Most big tool handles used to be made with ash or hickory. Good woods for canes and walking sticks.
<p>I like the cane project. The results were nice.</p><p>Would you please post an instructables on how to make a shaving mule?</p>
<p>I like the cane project. The results were nice.</p><p>Would you please post an instructables on how to make a shaving mule?</p>
<p>I like this Cane tutorial. The result was nice.</p><p>Would you please post an instructables on making a shaving mule?</p>
<p><a href="http://www.instructables.com/member/SparkySolar/" rel="nofollow" style=""><img alt="" src="http://cdn.instructables.com/F3T/WVBM/I1EU3X0W/F3TWVBMI1EU3X0W.TINY.jpg" style="max-width: none;"></a></p><p><a href="http://www.instructables.com/member/SparkySolar/" rel="nofollow">SparkySolar</a>12 minutes ago<a href="http://www.instructables.com/id/Chocolate-Batarang/CGFX22MI1NUCF52" rel="nofollow">Reply</a> <br></p><p>Thank you so much for the nice instructable. I love it.</p><p>Rima</p>
<p><a href="http://www.instructables.com/member/SparkySolar/" rel="nofollow" style=""><img alt="" src="http://cdn.instructables.com/F3T/WVBM/I1EU3X0W/F3TWVBMI1EU3X0W.TINY.jpg" style="max-width: none;"></a></p><p><a href="http://www.instructables.com/member/SparkySolar/" rel="nofollow">SparkySolar</a>12 minutes ago<a href="http://www.instructables.com/id/Chocolate-Batarang/CGFX22MI1NUCF52" rel="nofollow">Reply</a> <br></p><p>Thank you so much for the nice instructable. I love it.</p><p>Rima</p>
<p>Do you suppose that a hickory shaft and handle would be able to support a full grown man? I would like to make this for my grandfather, who was a shop teacher, and i think he would really like this. Thanks</p>
nice tools, ever tried making a bokken?
No, I haven't made a bokken (yet), as I don't know anyone who would use it. They don't look difficult to make and the shape is simple. I can imagine it would be a good exercise to create one with hand tools. I may have to try making one with some of the figured cherry wood that I have.
I do woodworking, and a friend of mine who is in the SCA made a wooden bokken. His first one was Purpleheart, which is very hard, but once it reached a certain point of stress, it cracked. I suggested to him that he use a springy wood, such as Ash, Yew, or Osage Orange, since such woods can bend and snap back to their original shape. Cherry I don't beleive would be a good wood to use for a bokken. It hasn't got the elasticity of Ash or Osage Orange. It would look good until you actually tried to use it in a practice combat.
Interesting tip. That makes sense that the bokken needs a flexible type of wood to withstand the impact. I didn't realize Osage Orange was flexible as Ash or Yew. I like Purpleheart for cane shafts but it's quite heavy. Some dense woods are still quite brittle as you mention, especially snakewood. Apparently there is good reason why baseball bats are made of Ash.
Osage Orange aka Boisd'arc, or Maclura Pomifera was originally used by the Osage native american tribe for bows. Long straight pieces can be obtained for those who want to make such a bow, just like long straight pieces of Ash are available for those who want to make their own baseball bat (I would probably rip an Ash bat blank in half lengthwise). Incidentally, Yew was used for bows by native american tribes in Washington and Oregon state.
Interesting info. I thought that Bois d' arc was a generic term for red colored woods. I have found that Osage Orange is excellent for high stress needs. I have found some that has tints of reds in it from contact with certain soils. Very beautiful wood. <br><br>FYI: The bright yellow/orange color oxidizes to a two toned yellow/caramel color, still very beautiful, but more subtle.
Fence posts made from Bois D'Arc will get so hard in 50 years, you cannot drive a fence staple into it. It does not rot.<br><br>There is an abundance of this wood listed on eBay Do an eBay search for each name:<br>&quot;Osage Orange&quot;, <br>&quot;Bois D'Arc&quot;, <br>and <br>&quot;Hedge Apple&quot;.<br><br>It is very reasonably priced on eBay.
thepelton:<br> I make canes from Bois D'Arc also, but from one piece of wood.<br> <br> You can see one here: <a href="http://walkingstickscanes.blogspot.com/" rel="nofollow">&lt;Blogspot&gt;</a><br> and here: <a href="http://reviews.ebay.com/MAKING-BOIS-D-ARC-WALKING-STICKS?ugid=10000000002188165" rel="nofollow">&lt;eBayGuide&gt;</a>
This reminded me of the same thing! LOL
I really appreciate this tutorial. Now, all I have to do is try to draw and then shape the handle...I am not an artist at all so this is going to be my greatest challenge but, I look forward to it!
Does this work for a colonial costume?
I never thought of hooking a shop vac up to a palm sander before. Good idea. And a note on the safety, i can tell you from experience that little bits and pieces will fly towards your eyes, i took a metal sliver to the eye because i didn't bother to put on my safety glasses. I was ok but it cost me a visit to the emergency room and a lot of pain so wear all safety equipment even if you think it isn't necessary.
<p>A couple of my friends and I are making a cane like this as a inside joke to our history teacher. If we wanted to put a signature on the cane before we put the finish on the cane do you have any ideas or recommendations on how we should do that? thanks</p>
<p>First sand the surface very smooth.&nbsp; You could use either a Sharpie, permanent ink pen or a wood burning tool. &nbsp;Practice on a scrap piece of wood first, as this is permanent.&nbsp; Also, test the scrap wood with the finish to make sure the Sharpie does not bleed.</p>
Very nice. I started hand carving a walking stick a few years ago, and it's been sitting, unfinished, in a corner of my shop ever since. It's coming out tomorrow. Thanks for giving me new momentum to finish it!
I've tried in the past to make a cane all in one piece and failed, your handle joining technique is great. I can't believe how simple you make it look. Thanks for the tutorial.
what is that wood thing with the red seat in step 8?!
The Shaving Mule (shaving horse) is an old fashion method of holding the piece of wood while you shave it with a spoke shave. These tools were used to make chair parts, etc. before power tools were invented. It's a very relaxing way of working with wood. The only noise is that of your hand tools against the wood, and maybe your humming while you work. It's Very Zen.
Padouk. It is very hard and has a bit of an open grain, and is very strong.
sorry... not what type of wood... what is the big machine in step 8, 5th picture, made out of bolted together 2x4s with the big red vinyl seat.
shaving horse ,lets you sit close to your work good for control ......nice work mmh
This a wonderful detailed how too . I'm a very experienced woodworker but I have never made a cane. A total thumbs up for the tutorial and the many beautiful canes you share on Lumberjocks .com
I really liked the tutorial. It was very informative! I like to make knives and just started reading about making canes and or walking sticks. I have been collecting them for a while and thought I would prefer to make my own. The materials I use for making knives are exotic and sometimes unusual so what better to show them off then on a cane for all to see. I have made an attempt at some walking sticks in the past here are a few examples of them (I call them "yardsticks"). Thanks, grizzledcamudgen
Iron wood would be perfect for this.
Very nice work , I have been on a cane for 7 years or so at first I turned 2 23 inch walnut or other hard wood ( I need a 45inch cane )put together with a dowel and a brass or copper pipe and carve a handle or just use a branch that shape I want ...now with arthritis ruining my hands I try to carve cane/handles but find it hard as well as holding the turning tools so have gone to branches ....maybe the belt sanders...spoke shaves and other hand tools with some mods will work ...I also find 11/4 inch poplar works for the shaft but the same color cane is kind of boring but if you do a bamboo shape for the shaft it works again very nice work
Thank you for the comments. I would love to see some of your work.
<a rel="nofollow" href="http://www.angelfire.com/ca6/Woodcarver/">here</a> are a few I have done not canes but fun carvings....<br/>
Awesome Stuff
I just finished the project. The plans and procedures were excellent. I think if I were making another one I would have shapped the handle on a lathe.
Nice cane! The reason I did not use a lathe for my <em><strong>Instructables</strong></em> is that most people may not own one and I do not like the uniform spindle look. The lathe makes the shaft look like a colonial style piece of furniture and I don't care for that style. My canes are made to show the hand crafted workmanship more than the industrial machine work.<br/><br/>Thanks for the feedback and happy cane making.<br/>
You are absolutely correct on afterthought. The spoke shave produces many marks, groves, etc. that are non- exhistent in spindle turning that adds character to the tapered handle. I did the initial sanding on my lathe; and finishing with working down to 320 grit in sanding with the grain off of the lathe. The shaft has a much more distinctive look than if it were merely turned to to a smooth finish. We have had many fine coments on your cane. People want me to make one for them

About This Instructable

243,700views

172favorites

License:

Bio: I love creating art and functional art is a challenge that I am enjoying by creating one-of-a-kind canes and walking sticks, as these can be ... More »
More by mmh:How To Make A Custom Fancy Walking Cane Wood Lovers Faberge' Egg 
Add instructable to: