loading

Step 5:

Flip the top over so it is out of the way.
<p>My issue is the belt came off than i found a an arm with a pulley inside...the only spot the pins in the bottom line up theres no screw hole, and even if there was it does nothing to tighten the belt.</p>
<p>Instructions are not complete. Pop the top off and fold back (ok). Unscrew the lint catcher (ok). Unscrew the front top door(ok). Now, what about the springs for the hatch door? Had to take both front doors off to access the idler. Pretty tricky reattaching the springs. Had to make some adjustments to refasten the bottom door.</p><p>Dryer is operational</p>
<p>There is no need for this, the instructions are correct, just pull front up and turn away. Never had to mess around with springs nor had to remove door.</p>
<p>I had the springs issue as well! This is a seriously old model of dryer. I couldn't even find the model number with an online search! LXE8700A0 What I needed to know was to take the bottom section off first. This is where you can disarm the two nasty springs. Take care not to pinch your hands with them. Also, beware that this area of the dryer can get pretty scary. There were lots of spider egg packs and such there that needed to be vacuumed out, so be prepared. </p>
<p>Being a self proclaimed &quot;JANE&quot; of all trades, I was able to repair our dryer using these instructions with the greatest of ease! Great Job!I would like to add one thing to STEP 10: if anyone is like me and question EVERYTHING, when you place the belt around the drum, make sure the &quot;grooved side is on the drum and the flat or colored side (depending on the belt you purchased) is facing up toward you.. It will make a difference!</p>
<p>Thank you very much Elaine! Being the woman of the house, and about to embark on this situation (after being told it would be an easy repair for my husband to do), it helped me to see you here. What might be obvious to some who are used to dealing with mechanical situations might not be so obvious to newbies. I appreciate you speaking up about your experience with this.</p>
<p>That was obvious when you see the motor pulley had same grooves and moreover grooves would'nt really serve any purpose outside</p>
<p>Very helpful. Couldn't figure out how to re-position the roller after the old belt broke(roller fell with no tension on it). This answered that question and more. Thank you!</p>
<p>I made it ! Excellent instructions...thanks !! The old idler had vanished...then I knew the black powder around the motor were its remains. Good thing you advised to clean outside drum - it was very dusty; and good thing you advised might as well change the pully assembly while at it :) saved me another trip to the parts site!</p>
<p>After the Internet everything more easy, now I know how to replace the belt. Thank you.</p>
<p>My dryer was screaming at me so I knew that there was something in there somewhere. Your Instructions were a huge help to me in order to diagnose the problem, turns out I just had to remove two heat shields from the back of the dryer in order to grab something that fell back under the lint trap, but either way this helped me. Thank you! </p>
<p>idler pulley -- this thing keeps popping off really easy. Did something break on it for it to be doing this? I finally got the belt back on and went to hand turn it (probably turned it the wrong way but still) and the thing popped right out! ARGH!</p>
THANK YOU THANK YOU THANK YOU!!!!! You just saved me $900 for a new dryer!!! My brother helped but I did all the grunt work!!!!! LOL Great instructions!!!!
WOW It would have taken me all day just to figure out how to get the top off the machine! Drying my first load on the new belt now, all seems well. The only (small) complaint I have is that I wish the article was more instructive on taking off the front of the machine, the little clips on the bottom messed me up. <br> <br>A little helpful hint: Just use something to rest the drum on to keep it from falling while you are trying to put the belt on. The cardboard box my new belt came in worked perfectly for this.
Very good article and pictures. When I got into my Whirlpool Estate TEDS840JQ0, instead of an idler pulley, I found the thing you see in this picture. We got this machine from a small business that fixes up and sells appliances. Is this part legit? Should I spend the 15 bucks on a pulley wheel and replace it? Thanks.
Mine just broke too, and has this 'glider' part, which seems totally ridiculous and a poor design; but you know what? It works! Thanks for adding the picture! Helped me out a ton!
I seem to have the &quot;glider part&quot; on my dryer. Ican't tell from the picture exactly how to run it under. Do I just pull the loop of the belt which is already around the drum under the &quot;glider and then around the motor????
The &quot;glider&quot; pictured has been discontinued by Whirlpool, and replaced with a tensioner with a teflon ROLLER.&nbsp;
After a bit of bad words, I finally got the belt on and working. The drum has to be PERFECTLY lined up or the belt will be too short. It's a really tight tolerance. Thanks for the great resource.
I found that it all comes down to the tension on the idle roller. Wrap the belt around the drum, rubber side in. When you have it positioned and the belt through the idle roller underside, push the idle roller rod towards the motor assembly. This gives you the slack you need. Still a squeeze but it'll get on there.
Between the article, this written instructional (http://www.davesrepair.com/DIYhelp/DIYWPLdrycleanlube.htm) and a high-temperature graphite lubricant, I was able to get things running quietly again.<br><br>Thanks.<br><br>
AWEsome! Thanks to the follow-up comments, too. I was looking all over for the round pulley, until I read on about the 'glider', and how to put it on. Seems like a stupid design, but the darn thing's working now! Thanks very much!
Great step-by-step, many thanks.<br> <br> There is also a good video of how to do it at this site: http://www.repairclinic.com/PartDetail/Drive-Belt/341241/529597?modelNumber=LG5801XSW3#repairHelpVideoTabs<br> <br> One caution if you use the video: they take the bottom part of the front off by levering with a screw driver at both sides. On our dryer the spring clips are at the the top of the bottom section about 3-4 inches in from the sides. You slip the screwdriver in and press them down to release. You have to get down on your knees with a flashlight to locate them.
Thank You! How did people do this before the internet?
In 2008 I purchased a belt, drive rollers, and a new belt tensioner.&nbsp;&nbsp; I made a huge mistake by not buying genuine Whirlpool replacement parts.&nbsp;&nbsp; The belt was OK, but the support rollers, and the belt tensioner roller was NOT the same as the original parts.<br /> <br /> The dryer made noise and finally the belt tensioner was destoyed!&nbsp;&nbsp; This month I bought knock off parts again, and immediately those parts caused a problem.&nbsp; The appliance store gave me a refund, I purchased genuine Whirlpool parts, installed them and the dryer works perfect.&nbsp;&nbsp; <br /> <br /> My dryer is a Whirlpool gas dryer purchased in 2003 and works greal.&nbsp;&nbsp; <br /> <br /> On this site on 4/9/09 spikeSpilker pictures a &quot;glider&quot; to tension the belt.&nbsp;&nbsp; That part has been discontinued by Whirlpool, and replaced with a &quot;roller&quot;.
A little off topic, but I had the same experience with knock-off Toro snowblower parts. Junk compared to the genuine Toro parts. Don't buy cheap Chinese replacement parts.
THANK YOU THANK YOU THANK YOU!!!! After learning that rather than buy a new (used) dryer, it could simply be a belt issue and not a motor issue, I was told to check the belt first. I had NO idea how to do that, and even so, how to change it. This site was a HUGE help (I couldnt have done it without it) and also a HUGE money saver. I appreciate all of the great pics as well as the step by step instructions. I didnt even need a new belt, my pulley had simply popped out and needed put back in.
I just replace the belt of my dryer Whirlpool, thanks a lot for your help, that was wonderful and really cheap.
These instructions were a great help. Note: I have a much older dryer with the door that opens forward instead of to the side. It has springs which must be unhooked. Remove the bottom front plate and unhook the springs. Pretty easy once I figured out how it was put together.
OMG! This freaking rocks! You saved me a ton of money on a repair and/or countless hours lost by doing it myself blind! Thank you, sir! I can dry my clothes again!
Awesome !!! This saved me about $150 ! Thank You Thank You Thank You !!!
OK. So hubby replaced the belt and vaccumed everything out. Apparently we have the &quot;glider&quot; that other posters say isn't used any longer. We put everything back together after vaccuming and it still doesn't tumble. Any other suggestions? Everything seems to turn easily when we are in there.
Thank you so much!! I might be admitting my stupidity here, but I would never have gotten the belt back on or the guide roller back in place without your disassembly steps. Runs like new. Thanks again!!<br />
<p>just wanted to say thnx from the bottom of my heart. you saved me $100 or so according to the estimate we got over the phone. i know nothing about dryers or appliances but now i can change a dryer belt. took me five minutes to put on and ten to put it all back to together and around room the way the wife likes it. your the man.</p>
This is fantastically helpful. Thanks!
Fantastic instructable. Great pictures and explanation. Paid only $15 for the belt and probably would have paid $150 if I were to call a service man!
Excelent
Saved me a a lot of money! $20 for the belt. Works great!!!
*in hypnotized voice* partselect.com must visit partselect.com must partselect.com is everywhere ah the Madness! AHH *explodes*
woohoo!! I did it!!! ty ty ty ty for this service, u guys are the shizzle!!!
This was exactly what we needed to fix our dryer. We got it done in no time once we saw these helpful pictures!
As an appliance repairman, I must inform everyone who reads this that this is one of 2 different whirlpool dryer styles! If you have the other style and attempt to take it apart in this fashion you might break the top panel and/or some of the internal elements of the dryer! Nice walkthrough either way! Thanks
Good day. I have a Whirlpool Dryer that has the opening to the side in the front, not at the top like shown. Is the principle for opening it the same? My unit is not tumbling at all. Thank you.
if you have the opposite style what you need to do is: at the very front corners of the console you will see 2 phillips head screws holding the console down(newer dryers have these in the rear).If you do not see the screws then they hidden under the endcap of the console. These endcaps are very easy to pop off. Just insert a flathead screwdriver under the top rear of the endcap, and pull towards you. After the endcap is off the screws will be at the base of the console. After the screws are out you can flip the console backwards, exposing three 1/4" screws (left)(middle)(right) near the rear panel that must come out so you can slide the top forward(not up) off the machine. Once all this is complete you will see 2 screws on the front panel(left)(right) side and your door switch wiring. Also you must take off the lower front panel to expose the other 2 screws that hold the front panel on. And this should give you full access to everything. ***warning*** there are a few newer styles still that do not use screws or endcaps but rather a small metallic clip that must be depressed with a putty knife(rarer style) If that is the case once you depress the clips in the lower corner(under the console), the rest of the teardown is the same as I have just explained!! Hope that helps.
OPENED THE DRYER. BELT (THIN, GOES AROUND DRUM RIGHT?) APPEARS TO BE INTACT. ANY OTHER IDEAS?
Will try it this weekend. Thanks a lot.

About This Instructable

402,951views

32favorites

License:

More by Natitude:How To Replace a Washer Coupler (Whirlpool or Maytag) How To Replace a Dryer Belt on Whirlpool Models 
Add instructable to: