Instructables

How to Make a Minimalistic (and Cheap) Laptop Case

I got tired of looking at the scratches and dents my MacBook suffered every time i tried to take it somewhere without throwing it in my rather large backpack. I needed something slim yet good looking. Something rugged yet inexpensive. I turned to my two best friends cardboard and duct tape! In this instructable I'll show you exactly how to make one of your own!
 
Remove these adsRemove these ads by Signing Up

Step 1: Materials and Sizing

Materials: cardboard, duct tape and a laptop.

I was lucky enough to find a box that was just the right size for my macBook. You may have to hunt around to find one you like but as long as there are no creases in the middle (eg too small a box) you should be ok with any size.

Your box is perfect if you can just barely stand your computer on end when it's all constructed.

Step 2: Trimming, Part One

Alright, screw your courage to the sticking place and prepare for first blood.

Cut your box open down one of the corners. Then trim it down to two sections and loose two opposing flaps.

There will be two measurements you will have to make now. The first corresponds to the depth or hight of your lappy. The second corresponds to the width. The easiest way to do these is to just roll it. First set it so the bottom lines up with the edge of the two flaps (like it is in the pictures) then set it up on end while keeping one edge on the cardboard like a hinge. If you are careful you will get the exact hight measurement you need. Mark with a pen. This measurement will be a crease. Keep rolling it so its lying upside down. Mark again. This measurement will be a cut.

You can crease however you like but I cut through the first layer down on the inside down a ripple of the corrugated middle layer.

see the photos. I remember something about 1000 words....
1-40 of 44Next »
jessyho86201311 months ago
that design look nice there, good job!! :)
Freshbott23 years ago
I'm considering making something similar to this only out of material, I like the look of this design.
royshearer6 years ago
Here is my version of this laptop case - I made a removable accessories tray for the power supply, hard drive, card reader and mouse. Removable as sometimes I need that stuff, and sometimes not (its a lot to carry around I know). Brought to you by the power of velcro, the flap can either fasten to the tray or the bottom of the case when the tray is not in use. Thank you, very useful instructable!
IMG_2072.JPGIMG_2073.JPGIMG_2077.JPGIMG_2078.JPG
I like the tray, good job!
smart....
Wow thats Flippin awesome Omfg i love it LOl I may make one like urs and Paint it THks for the tray idea
That is amazing! if i end up making a case, i will definity use this design!
Great! I think if I did it again I would try making the tray bit even more compact and give the case a handle of some sort.
Is that a tiny External HD i see?
Well, its not that tiny, its a Lacie thing, about 100x130x15 I'd say.
zoundsPadang (author)  royshearer6 years ago
Wow that's really sweet! good to see an elaboration on my original design!
iLLiDiaN4 years ago
 nice idea here, keep up the great work
I made this with an amazon box, no cutting required, it fit my macbook perfectly. I also used wrapping paper and poorly applied sticky-back plastic. I was so easy and cost me nothing.
and here it is
IMG_0023.JPG
I think I might try this with cardboard and oilcloth. I think that will work just as well. :D
recritchlow5 years ago
Very neat. Put it into the cardboard and ducktape gallery. I expect this would be a TSA checkpoint friendly laptop case, too. It has no extra pockets and no metal parts to obscure the x-ray view. I think I'll add an extra layer of cardboard around the edges to provide extra padding, especially in the corners.
chriss7275 years ago
it would be cool if you also add a strap
I tried this and it was a relative success just make sure to cut the pieces a little bit bigger so the laptop in question fits but isn't too snug like mine was.
zoundsPadang (author)  schoolgirl8678696 years ago
I made mine rather snug on purpose. If it's cardboard it should slide in and out nicely.
I made mine too snug I have to wiggle it out but i found a way to strech it so it isnt too difficult
André6 years ago
Nice! I love the idea!
JoeyJaroz7 years ago
My Compaq C55NR looks just like your MacBook except mine says Compaq on the front And it cost like 1/5 the price of your mac lol
zoundsPadang (author)  JoeyJaroz7 years ago
glad you like it. I love my macbook, which was worth the price and will continue to be for years to come too!
true, my Compaq is allready slowin down im gettin a mac as soon as i get the money
Ora7 years ago
How well to spray painted stencils hold up on duct tape?
rasta_bhoy Ora6 years ago
paint will slide off the duct tape. try painting or stenciling the cardboard first and just leave that space free and just put duct tape for borders. your choice
zoundsPadang (author)  Ora7 years ago
meh. Depends on what kind of spray paint you get. If you were to wrap with clear tape after spraypanting however....
kittyno6 years ago
couldn't tyvek be used as well for a more rugged cover, in lieu of duct tape, or at least to cut down on the duct tape usage?
zoundsPadang (author)  kittyno6 years ago
You could. Of course, the amount of duct tape used in any given project is directly proportionate to the awesomeness of the final product. Also, I've used this case since i built it about 6 months ago and there's no degradation at all so it shouldn't be an issue.
koekoek6 years ago
Really cool! :P
lilianne6 years ago
we had to make this for school, it's really fun!
vurrud6 years ago
It´s really cool. Thanks for the idea
zoundsPadang (author) 7 years ago
A few people were afraid that this would scratch a 'book but after a few months of use I'm proud to say that my macbook is spotless!
e.bender7 years ago
Good instructable. i recently got the new 17 inch VIAO notebook, and there is not a cover that will fit it, its kinda huge. I may have to try this one. Thanks EB
Use corroplast (plastic cardboard) for a longer-lived case. Old election signs are cheapest. tOM
I formed a relationship with my local convenience store's owner - he now saves all the coroplast signs (soda & tobaco ads) for me when the promotion they're used for is over.
buZztiaan7 years ago
nice one :)
(removed by author or community request)
yeh, you will need to overshoot the distance for that second fold on the top a bit but as you use it it will stay closed better. I flirted with the idea of magnets but decided that to be effective they would have to be strong enough to do damage to my computer after sliding it past them over ad over. I like the idea of velcro but my dorm is suspiciously devoid of it. :)
(removed by author or community request)
1-40 of 44Next »