How to Make a Portable Game System

 by 1up
FeaturedContest Winner

Step 5: The Batteries

Before we discuss where to get batteries, you need to think about what kind of batteries you want. There are two main kinds; NiMH and Li-ion.

NiMH batteries are the kind you see that power RC cars. They come in battery packs, and need no special circuitry to charge them. They are very heavy.

Li-ion batteries are very common. They power laptops, portable DVD players, cell phones, etc. They are very lightweight and have lots of mAh, meaning that they can power a portable for a very long time. They require special circuits to charge them.

Conventional batteries are what you use for all sorts of electronics. These batteries are your standard AA, AAA, 9v, D, and C batteries. These are relatively cheap, but they aren't rechargeable. (Unless, of course, you buy rechargable ones.) Conventional batteries can get expensive over time, and they are a little heavier than other types of batteries.

As you can see, all types have their pros and cons. For NiMH and Li-ion types, there is a rule.

You can get batteries that are:
- Cheap
- Lightweight
- Long-lasting
Pick two.

If you want to choose NiMH, then you don't have to do much for them. They are cheap, and to charge them, you just feed power straight to them. Dead simple. Unfortunately, they are often heavy and big.

Li-ion batteries are great, but require a bit of work. They need special charge protection circuits. They cannot be shorted or overheated. Despite these things, they are very worthwhile. They are small, thin, lightweight, and long-lasting. The bad part is that they cost quite a bit.

WARNING: If you do not have a charge protection circuit, Li-ion batteries will EXPLODE. These batteries are dangerous if not used properly. They may not be shorted, overcharged, or undercharged. If you are buying Li-ion batteries from eBay, you MUST buy a Universal Battery pack. These battery packs have their own built-in charge protection circuits and often have charge indicator LEDs. If you do not know much about Li-ion batteries and their various protection circuits, then you MUST use NiCD.

Conventional batteries are great for the "average joe." They are readily available and are easy to use. But, unless you get rechargeable ones, these can cost quite a bit in the long run. The good thing is that these batteries come in many shapes and sizes to suit your needs. If you're going with conventional batteries (Like AAA's, AA's, C's, or D's), then you need to pick between battery life and weight. AAA's will be very light, but have a short battery life. D's will give you many hours of playtime, but they are extremely heavy. AA's and C's are in between.

There is one more important factor: mAh. mAh stands for Milli amp-hours. The mAh of a battery is how many mA that battery can provide for an hour. If a console and screen that together consume 1,000mA is being powered by a 1,000mAh battery, then that portable would run for 1 hour. Find batteries that have a high mAh. Batteries with 3,500 will run an NES portable for about 3 hours.
To find battery life, add the mA consumption of the console to the mA consumption of the screen. Divide that number into the mAh of your batteries. This may all sound confusing now, but the more you work with the batteries, the more it makes sense.

Here is a useful topic that has the mA consumption of many consoles and battery life estimates for them.

Now we can finally get started on this thing.
 
Remove these adsRemove these ads by Signing Up
1-40 of 67Next »
jellygonewild909 says: Nov 21, 2012. 10:17 PM
will this work http://www.onlybatteries.com/showitem.asp?ItemID=11559.47&cat1=20&uid=1096&utm_source=shopzilla&utm_medium=versafeed&utm_term=11559&utm_content=hitech&utm_campaign=rechargeable+replacement+batteries+11+510+200&sid=shopzilla-com
jellygonewild909 says: Nov 21, 2012. 10:08 PM
does the voltage matter?
Clemasterable says: Jun 23, 2012. 10:47 AM
Hi I'm planning on making a portable NES. I plan on using a DealExtreme 2.5 Screen. Do you think a Panasonic Alkaline Plus 9v would work? If yes, how many would I need and how many hours would I have?

1up (author) in reply to ClemasterableJun 23, 2012. 10:07 PM
It would work, but probably for only a half hour, max. A 9v battery doesn't have a high mAh rating. I would find a different, rechargeable battery.
viper56 says: Aug 22, 2011. 3:19 AM
Hi I am new here and I just bought PS1 Screen from ebay and I just want to know which of these battery I have will probably work

1- I have a racing car batteries which written on it Ni-cd 10xAA 800mAH 12V

2- Ni-Cd AA700mAh 9.6v and another one Ni-Cd AA 700mAh 9.6v

3- Also, I have battery made in Taiwan for GameBoy no details written on it but on the box written on it TV Game Battery Pack For Game Boy Charges 50 Sec. and it have an adapter: Model: MA-5-9205 / Input: 240V AC 50Hz / Output: 12V DC 400MA

So are any of these can work !!
����������������.jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg����������������(������).jpg
nquast1 says: Aug 15, 2011. 2:14 PM
I was thinking about using a toshiba satellite battery for a nintendo 64 portable;
the battery has 3600mAH. How long of a battery life should I expect from that battery?
1up (author) in reply to nquast1Aug 16, 2011. 11:13 AM
Almost three hours. The problem with laptop batteries, however, is that there is no way to charge them without the original laptop. Plus, they're usually 12v when you only need 7.5v. But, if you 're fine with using the laptop with the charger, and having some extra heat from your regulators, I suppose it's fine.
Nisalotaco says: Aug 2, 2011. 9:09 PM
For a person who is new at this stuff, has a low-er budget, and likes lighter things (me), what battery do you recommend. I don't really like explosions, they hurt. And I'm not sure that i would want to spend the extra money on the protection for that... So the heavier, easier to charge option, how heavy is that? I just want to know these things before i spend more money than i have to...
Nisalotaco in reply to NisalotacoAug 4, 2011. 12:48 PM
I decided on using a 7.2v, 3300mAH, NI-MH battery for my console. Its a little heavy, but if i place the controller in the right spot, im fine... My question was: It has this little adapter so that it hooks up to this recharger and the toy car it came from, so i dont wanna rip it out. Does that mean that i should take the adapter off of the toy car and solder it onto some thing to hook up to the power source?
dtilley says: Jul 29, 2011. 6:58 AM
How much playtime would 5 AA's give you?
dtilley in reply to dtilleyAug 3, 2011. 12:26 PM
found it its 1250 mAh would that work?
dtilley in reply to dtilleyAug 3, 2011. 12:23 PM
ok, now im gonna use a 9.6v. NiCd rechargable battery from a new bright rc car but i dont know the mAh
srioux-1 says: Jun 29, 2011. 4:04 PM
how many volts did your battery have?
redsoup says: Dec 4, 2010. 9:03 AM
i found the worlds greatest batteries, they are Tenergy D bateries, their compact so thier less weight than Ds added up thier 13v, and they are 10,000mah.
nintendocrazzy says: Nov 30, 2008. 3:04 PM
i am thinking about using a conventional battory and a ps1 screen for the NES portible now what type of conventional battory do i want
1up (author) in reply to nintendocrazzyDec 1, 2008. 6:25 PM
Did I forget to talk about that part? If you're going with conventional batteries (Like AAA's, AA's, C's, or D's), then you need to pick between battery life and weight. AAA's will be very light, but have a short battery life. D's will give you many hours of playtime, but they are extremely heavy. AA's and C's are in between.
WeaponMaker96 in reply to 1upJul 11, 2010. 10:23 AM
I have 2 double A rechargeables from Duracell 1.2 volt each and 2000 mAH. how many would i need to power my NES for around 2-3 hours?
ryguy425425 in reply to WeaponMaker96Dec 1, 2010. 6:32 PM
I'm not sure of the power draw of an NES, but 8 of them would power a Nintendo 64 for 1-2 hours. (I imagine it would give you your 2-3 hours using an origional Nintendo, but I could be wrong).
MrExcellent in reply to 1upOct 28, 2009. 11:53 AM
Sorry, just the last question ^^:
"AAA's will be very light, but have a short battery life"
But if I take rechargeable AAA's, they have a short battery life?
1up (author) in reply to MrExcellentOct 28, 2009. 4:36 PM
Rechargeables have even shorter battery life. I wouldn't use AAA's at all, really, not for this portable.
MrExcellent in reply to 1upOct 29, 2009. 1:21 AM
OK thank you very much for all!
I will take AA's
nintendocrazzy in reply to 1upDec 4, 2008. 3:14 PM
cause i dont mind the weight as long as its not supper supper heavy id rater have lots of play time
nintendocrazzy in reply to nintendocrazzyDec 4, 2008. 3:18 PM
how many D battorys do i need?
1up (author) in reply to nintendocrazzyDec 5, 2008. 4:00 PM
One D battery is 1.5v, so you would need to put 5 of them in series to get 7.5v.
nintendocrazzy in reply to 1upDec 7, 2008. 12:06 PM
thats not over supper heavy do u think
1up (author) in reply to nintendocrazzyDec 8, 2008. 3:49 PM
I think it's super heavy. Have you held 5 D batteries? Try C cells instead.
nintendocrazzy in reply to 1upDec 6, 2008. 6:56 PM
thx
nintendocrazzy in reply to 1upDec 4, 2008. 3:11 PM
(removed by author or community request)
Chainblade says: Nov 18, 2010. 10:10 PM
Hey, quick question: I have two 3.6v NiMh 800mAH batteries from some old handset phones. The charger is a basic 9v +mid pin. If I paired these in series, would the outcome be 7.2v 1600mAH? Seems perfect. And would the charger actually charge both? I don't intend on using it for that long of a time span, and the batteries are quite small. About 1x2" each.
ryguy425425 in reply to ChainbladeDec 1, 2010. 6:28 PM
The charger might charge both, but you might want to invest in a protection circuit. 800mAh is actually pretty low, if you want more then half an hour of game time on a charge you should probably just get bigger batteries (or more of them if possible). My portable n64 has a 2000mAh battery, and that's considered very low.
1up (author) in reply to ChainbladeNov 21, 2010. 9:48 PM
If you put batteries in series, they voltages add. In parallel, the capacity adds. So, you would get 7.2v at 800mAh. Plus, you need to make sure you have an actual charger for NiMH batteries.
Pale_Flyer says: Jul 28, 2010. 9:49 PM
You forgot Ni-Cd, which, even being a piece of crap, should still be mentioned. Ni-MH are miles above the old Ni-Cd, but Ni-Cd is still here!
mebecj says: Dec 19, 2009. 9:51 PM
 I'm just going to make sure I'm doing this right. So for this portable setup I'd need around 7.5 volts. And according to the article, this setup will draw around 750 mAH?

Are there any specific batteries you could reccommend from say, RadioShack, that would work well here and offer a good amount of playtime?

And I can't seem to find one of those Universal Battery packs, can you give me some sort of example of one?

Thanks in advance!
Madrias357 in reply to mebecjJun 18, 2010. 5:07 PM
I can recommend the Ni-MH batteries. Get a couple chargers, and maybe 2 or 3 of the 3000 mAh batteries. They produce 7.2 volts, just FYI.
ThatGuyXXX in reply to Madrias357Jul 1, 2010. 1:06 PM
Would 7.2 volts be enough to power the entire portable?
Madrias357 in reply to ThatGuyXXXJul 1, 2010. 7:33 PM
He did say "around", and most devices are not going to mind 0.3 volts less than 'optimal' power requirements. You get as much fluctuation after voltage conversion, unless there's a voltage regulator.
mebecj in reply to mebecjDec 20, 2009. 4:06 PM
 Didn't feel like reposting the whole this to change the mAH, I missed one part of the post.
chewbaccaa says: Jun 22, 2010. 8:50 AM
hey, love your instructable im hoping to do this with a snes, and for the screen im using a gamecube screen instead of the psone screen errmm... the reason why im writing this is becuase i want to use a rc battery the voltage is 7.5 but im a bit confused on how to do it? :/ anyway niice instructable  carry on  thanks in advance
1up (author) in reply to chewbaccaaJun 23, 2010. 2:27 PM
The Gamecube screen might be able to take 7.5v, you should try it. Check out the ModRetro or BenHeck forums for information on how to power a SNES and get audio/video from it.

JJ7745 says: Feb 5, 2010. 10:43 AM
Whats the safest battery route to take.
like what has the least chance of blowing up in my face
And how big an explosion.
1-40 of 67Next »
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!