Introduction: How to Make a Simple Macrame' Bracelet (or Necklace)

Taking a long road trip this summer? Well, we know how boring those can be. That's why we're gonna show you how to make some awesome hemp bracelets. It'll keep you awake and you can keep the driver awake. Plus, hemp is for both guys and girls, so guys, get our your hemp too and let's get ready to hit the road!

For more how to's, be sure to subscribe to our show on iTunes and stop by our website, Threadbanger

Here's the complete show, but read on for step-by-step detailed instructions.


Step 1: The Hemp

Get out your hemp twine. if you don't want to use hemp there is a wide variety of colored cord you can chose from. the thicker the cord the bigger your bracelet or necklace. Cut off two long strands.

Step 2: Loop the Hemp

Take one of the strands, fold it in half and loop it over a rounded stick such as a paint brush or pencil. Do the same to the other strand. Now, you have four strands hanging down.

Step 3: The Knot

Take the right strand, pull it over the two inner strands and under the left strand. Pull the left strand behind the two inner strands and through the loop created by the right strand.

Step 4: Half Square Knot

This is a half square knot. Pull it tight to the top. And, repeat those steps over and over and over. You will get this twisted look.

Step 5: Adding the Shell or Bead

Once you are about half way done, get out a special shell or bead and pull the 2 inner (called the "anchors") and pull them through the hole in your shell or bead.

Step 6: Almost There!

Continue to tie half square knots until you have reached your desired length. Now, remove the stick from the loops and pull the anchor strands to make your end loops a little smaller.

Step 7: You're Done!

Pull two of your strands through the end loops. Put it on your wrist and tie a knot. For a necklace, just make it longer. Add more beads or shells or go without any at all... hey, it's up to you!

Comments

author
rxima made it! (author)2016-07-31

it looks a bit like DNA :)

author
rxima made it! (author)rxima2016-07-31

but very cool

author
SIRJAMES09 made it! (author)2011-12-29

always wondered how they did that....

TY for sharing

author
How to Macrame made it! (author)2011-05-27

I like the "take it with you" approach. I'm always falling asleep in the passenger's seat, so this is a great idea!

author
hey girl rawr made it! (author)2011-01-23

Alittle too fast of a video but after watching it a few times a figured out how to make a pretty cool braclet :) (';')

author
wobbler made it! (author)2010-08-16

Great Instructible. I'm going to make one tonight. However, for a necklace, I'd make sure it has a weak point or clasp so if it does get trapped or pulled it breaks away and doesn't strangle you!

author
redbeatles made it! (author)2010-06-22

Very Biautiful!

author
CrazySheep made it! (author)2010-06-15

Roughly, how long should it be for both a bracelet and necklace? Using twine like yours?

author
brokenbones made it! (author)2010-02-27

Thats wiked beast

author
NatureBoom21 made it! (author)2010-02-17

so..... the 2 outer strands go around and around the 2 middle strands?

author
R4Man18 made it! (author)2009-11-26

did it in a movie vehic... very impressive and cute foot

author
Khaos11 made it! (author)2008-08-09

mine doesn't twist like yours does, it just stays flat :P idk what I did wrong but it still looks cool thanks

author
midnightguitar made it! (author)midnightguitar2009-09-04

ok dude heres what you gotta do .Always do your first cross over from the same side it doesnt matter what side but its gotta be the same side

author
Ferrite made it! (author)Ferrite2008-08-18

You keep alternating which cord goes over which, you have to keep going the same to to make it spiral.

author
Khaos11 made it! (author)Khaos112008-08-20

o ok

author
icedog515 made it! (author)icedog5152008-09-24

hey, do u know where i can get some monster-hitman? you seem like you like monster

author
Khaos11 made it! (author)Khaos112008-09-27

no, i havent been able to find it either

author
icedog515 made it! (author)icedog5152008-09-27

-.-

author
Khaos11 made it! (author)Khaos112008-10-11

but your right i do love monster

author
bubba77 made it! (author)bubba772009-03-16

buy it in bulk at bj;s :D

author
jason-the-ace made it! (author)2009-04-13

i cant doo it lol feel like a nob, good vid tho

author
austinburke. made it! (author)2009-02-21

mine wont twist! and im tying the same knot the whole time!! please. any suggestions?

author
baconmanx9 made it! (author)2009-02-16

after you attach the hemp to the dowel or pencil, putting the pencil under a clip board really helps, 2 free hands and a work surface

author
making_hands made it! (author)2008-10-01

thanks !! well done !!

author
karoclou made it! (author)2008-02-09

Where did you buy the roll of hemp? How much was it?

author
Ferrite made it! (author)Ferrite2008-08-18

I usually get my hemp and other knotting materials here it is good quality. The hemp and cotton cord is closer to the bottom of the page.

author
anthony12 made it! (author)2008-01-04

thanks guys it worked and the bracelet looks great

author
adoqpweoriuqwer made it! (author)2007-07-26

Rather than holding on to the dowel the whole time, after finishing this step, put the dowel under your toes and bring the hemp between your big toe and the next. This way you have two hands free and can make tighter knots.

author
thumbelina made it! (author)2007-07-05

I make these all the time, but i never thought of putting it on a dowel, I always just tape it to my leg haha.

author
bumpus made it! (author)2007-07-03

looks like you got so bored on your roadtrip that you decided to make an instructable haha cool

About This Instructable

249,168views

398favorites

License:

Bio: Threadbanger is a network for people who love to DIY, recreate, refashion and craft. Forget about corporate stores, we're here to help you create ... More »
More by threadbanger:How to Fuse Plastic Bags into a Laptop CaseHow to Sew with Conductive Thread with Diana EngHow to Make a Corsage, Threadbanger
Add instructable to: