Instructables
If you ever need to wrap a package or box for mailing or make a box for a special project, you need to have tape handy. Especially helpful when wrapping gifts at Christmas time or other holidays. I came up with this idea to be able to use only one hand, tear off what I needed and hold the project with the other hand. Tape is easily added or removed, and the whole thing is easily stored as it is held in place by a c-clamp or other clamp of choice.
 
Remove these adsRemove these ads by Signing Up

Step 1: Parts you need to make this

There are 5 pieces of wood used in this project. I cut down a two by four that I salavaged.
1. Base: 3/4 inch pine, 7 1/4 x 11 inches.
2. Two uprights: pieces of 2x4; 2.5x2.5x1.5inches.
3. One crossbar: 2 1/2 x 10 x 1 1/2inch.
4. Tape cutting mount, 2 1/2 x 6 1/4 x 1 1/2inch.

Total= 5 pieces

Two bolts with nuts are needed: 5/16 x4 1/2 bolts with nuts and 2 washers each.

One piece of hacksaw blade, cut or broken to fit the tape cutting mount.

Step 2: Drill holes in wood pieces

The holes are drilled in the two uprights to hold the crossbar with tape in place. Drill the crossbar, uprights and base at the same time so that there is no alignment problem later on. Using a long 3/8 inch bit does the trick.

Also, drill three holes in the hack saw blade to be able to attach it to the cutting block. (Use a 3/32 in bit for these short screws). Three holes are drilled in the botton of the base and into the cutter mounting block. Use a 1/8 inch bit for this step.
mkambas11 months ago
nice and clean ible, thx much!
some time ago i recycled a wooden toilet-paper roll holder after our bathroom was renovated. but now i've switched to a longer paper towel holder for all kinds of tapes. reused the serrated long blade from a plastic wrap dispenser i had saved once, before discarding the empty box!
badpanda3 years ago
Nice job, I just posted a similar contraption without seeing this one first... I guess we both had the bright idea of finding a new use for old jigsaw blades. Yours looks significantly easier for people who don't have a lot of tools, in particular a router. http://www.instructables.com/id/Multi-Tape-Dispenser/
I made something similar some years ago. After renovating some bathroom fixtures, I took the leftover chrome toilet tissue roller and mounted it to a small slab of 3/4" plywood for holding holiday ribbon rolls. It makes it easy to remove or add new or spent rolls of ribbon, but it doesn't have a cutting strip. After seeing your nifty gadget, I'm thinking I should add some sort of cutter, like maybe one of those cheap, small plastic slide cutters for trimming photos (which I already have,) or perhaps cut a small section off one of my self-healing mats, attach that and store it all together with a rotary cutter or exacto-blade. I added a photo of it. The spacers are donut-cut foam sheet.

But, I think now I'll have to make one like yours for tape rolls, too! This one will have the cutting mount, tho. I may pick up a couple cheap TP rollers for starters, and maybe mount the arms farther apart, then use a trimmed down spring tension curtain rod instead of the usual rollers. I have to say I like the idea of using PVC pipe, since tape rolls have the larger holes. Two holes could be drilled at each end opposite each other and long screws added atop the 2 supports, sticking up. The pipe could then be easily slid on and off over the screws. Cut off the screw heads, and a wingnut could be added to secure the pipe as well. Big thanks for sharing your idea. Works for me!
RibbonHolder.jpg
Creativeman (author)  WonderWidget3 years ago
Thanks for your comments, and especially for posting the picture...saves a lot of time and makes you organized, right?
Organized. Yeah, right. I'm one of those who instantly understands how to 'make' organization better but is terrible at 'implementation'!!! I mean, look at how the supports aren't even centered. And now having noticed that, it's driving me nuts! I may have to turn the plywood over and remake the whole thing. Yours truly, OCD. LOL.
guyzo353 years ago
I just finished making it for our machine shop at work, thanks for the idea!
Tape Dispenser.jpg
Creativeman (author)  guyzo353 years ago
Good work guyzo35! thanks for posting the picture, makes it worthwhile to do these things. How's the duct tape work with this? It is so damn hard to pull off, I've pondered how to make a dispenser for that...I'd pull the workbench over if it wasn't secured! I have thought of drilling holes in the base and attaching it with bolts instead of the clamp....same solution, different approach! Cman
I put the clamp on the corner closest to the duct tape roll, to reduce the torque, so it works pretty well. A second clamp would do the trick, but the bolts would save you the two clamps with relatively little hassle.
pudi.dk4 years ago
Weird. I made a multiple tape dispenser, searched on Google for something similar and came across this. I thought I was the first to think of a hacksaw blade but you beat me to it.
I use a piece of PP pipe that fits the inner rings of the tape. A wooden plug in each end, each rolling on a bended piece of stainless steel plate that I found.
Only downside I can think about is that hacksaw blades are only sharp in one direction, to allow cutting when the hacksaw it pulled forward on an object. This would mean that you're limited to pinching the tape on an angle to get it off.
jamwaffles4 years ago
Might be a bit unrelated but anyway...

My friend has a saying that goes with the two tools in his mountain-biker's toolkit: if it moves when it shouldnt, use duct tape but if it doesnt move when it should, use WD-40. Maybe someone could make a gun that combines the two and instantyl fixes anything?

James
dontno5 years ago
What! No duct tape on that dispenser! I'm going to make a big huck-a-lukka dispenser to hold massive amounts of mans best friend "Duct Tape!"
clgonsal5 years ago
Not sure how well it would work, but I wonder if a possible alternative to a hacksaw blade could be the serrated strip of metal from a used box of aluminum foil.
Creativeman (author)  clgonsal5 years ago
Sure it would work! I just wanted the strength of a hacksaw blade so that it would last. Cman
Da_Fudge5 years ago
Great idea! I'm going to have to try this! Also, that hacksaw blade is an ingenious idea!!! Keep up the great work!!
Creativeman (author)  Da_Fudge5 years ago
Thanks ! Cman
is that a buck bros hacksaw blade I see?
Thornburg5 years ago
The hacksaw blade is absolutely genius. Good work
Creativeman (author)  Thornburg5 years ago
You think? thanks for the compliment. Cman
Chico5 years ago
Very useful! I'm going to make one! Thanks! As an improvement, I will use spacers between the rolls to keep them from rolling together and to separate the strips to provide clearance for the fingers to pull up the tape cleanly. I LOVE TAPE.
Creativeman (author)  Chico5 years ago
Not a bad idea...thanks chico. Cman
juanangel5 years ago
Excellent. Add a water receptacle with a brush or sponge, that fits inside the receptacle for the tape that needs to be moisten. It will be a removable one, in front of the blade. you have to scrape off some wood so the tape fit under the blade, closer to the water. A PVC pipe could make it lighter. Thats how I build one for a friend. Yours is longer. Mine was single. I like yours.
stuartkeane5 years ago
Dear Creative Man, very Good I'm going to make one tomorrow over here in the U.k Thanks & Keep creating
Creativeman (author)  stuartkeane5 years ago
Thank you. Cman
Made One today and it's great. it's also a good place to find all your different tapes in one place. I made mine the full width of a large axsaw blade Cheers Stuart
jsoroko5 years ago
briliant. I'm probably going to make one later today - two thoughts/questions - (1) any anticipated problems scaling it up (or wider) ? (2) with dogs, kids, and clumsy adults (me) in the house - wondering about a cover for the sharp edge when not in use. Perhaps a slice of pvc piping ...
shooby5 years ago
Could use the blade from an aluminum foil or pastic-wrap package...
jflynn_junk5 years ago
This looks good with a couple of changes. A round piece of wood for the tape to sit on using a wing nut as was mentioned earlier to make it easier to change tape, and possibly put a CD between each tape to try to keep them from getting stuck together. Or perhaps cotter pins in place between the tape.
Creativeman (author)  jflynn_junk5 years ago
All good ideas, thanks! Cman
yay..... I will make one.
madest5 years ago
This comes in handy, except i made mine with wingnuts that weren't countersunk so that the tape replacement wouldn't require tools. Thanks for the excellent submission.
Creativeman (author)  madest5 years ago
You're welcome. That's a good idea....I may adapt it, would save a bit of time,eh? Cman
mg0930mg5 years ago
I really like your stuff. 5 stars, and favorited, AND SUBSCRIBED!
Creativeman (author)  mg0930mg5 years ago
Thanks MG....Cman
Superstormj5 years ago
Cool. I was just clicking on your username, and looked at your projects. I looked at the hotwire, and then decided to refresh your user page. BAM. This new instructable comes up. I think it's kind of wierd that I would just "want" to refresh, and a new instructable comes up.. I dunno. Anyways, cool idea.
Creativeman (author)  Superstormj5 years ago
Thanks...I'm hard at work, but now it's break time! Cman.