Picture of How to build a Multi-Touch surface
Multi-touch gestures are the latest and greatest way to interact with your computer.  However, commercial systems are not widely available and are expensive.  Fortunately, you can do it yourself better and for less cost.

Principle components (Click links for product info):
$35 PS3 Eye Camera (Recommended but any decent webcam will work)
$20 IR bandpass filter
$200 5-meter dimmable IR LED Strip
$1000 Any recent/decent computer (PC/MAC)
$1000 Any projector >2000 lumens (NEC NP410W)
$40 Front surface mirror
$80 Abrasion resistant acrylic sheet (23" x 35" x 0.236")
$130 Rear projection acrylic sheet (23" x 35" x 0.118")
$145 EndLighten acrylic sheet (23" x 35" x 0.394")
Total: ~$2500

Software (Click links for downloads):
$free CCV (Used to turn images into blobs)
$free CL-Eye Platform Driver (For PS3 Eye camera)
$free Multi-Touch Vista (Optional Multi-Touch TUIO driver for Windows integration)
$? Windows 7 (Recommended)

Written by Justin Klaassen, Duke University B.S.E. 2012
Sponsored by the Duke Library

Remove these adsRemove these ads by Signing Up

Step 1: What is a Multi-Touch surface?

Picture of What is a Multi-Touch surface?
 A Multi-Touch surface is essentially a giant touch screen that can process multiple touches at once.  And in our case, a virtually unlimited amount of touches.  By allowing multiple touches, gestures can be performed on surface.  These gestures are typically simple things like pinching and pulling on an image to zoom in and out.  By supporting gestures like these interfacing with a computer becomes much more intuitive and fun.  In a public place, a Multi-Touch surface can be a real attention grabber.

Step 2: How does it work?

Picture of How does it work?
 There are a variety of different technologies that can be used to create a Multi-Touch surface.  All or most surfaces rely on optical based technologies that work using infrared light (IR).  The technology used in this guide is direct surface illumination (DSI) and is explained by the comic below.  The basis for using DSI over other similar technologies is that it allows for a protective abrasion resistant layer to be on top, protecting the delicate under layers from the users touches.  The order of acrylic layers on the surface is as follows:

1) Touch surface (Abrasion resistant acrylic)
2) Diffuser/Projection layer (Rear projection acrylic)
3) EndLighten acrylic
1-40 of 118Next »
i had built a multi touch table brother but i could nt adjust it touch in a proper way .. it is touching symentaniously many areas at a time .. i through out the projector rays with the help of a mirrior .. is it wrong ?
DCFIGHTER1 year ago
nice build brother
but one following question to this
u said the price and cost for the following Multi-Touch surface would be 2500, can you please suggest the lowest price that i could spend on such a build because firstly i am 17 and secondly i am trying to save as much as i can
Thanks for the detailed instructions also
tinker2342 years ago
thanks i loved this article but i had some qusteins how can i set up the software i tried before but i never could get it to work where can i buy acrilec cheaply and with the eprojecter whjat do you do
frankencois2 years ago
so with the projector, if i were to be using a short throw projector, i would not need a mirror to reflect the image onto the screen, am i right?
Can you tell me approximately how far the camera needs to be away from the top?
Depends on your camera and lens.

I suggest just set up the camera, point it to a wall with an area marked that is the size of the screen desired marked on the wall. Once you can see all edges of the desired screen clearly, you are the 'right' distance away.

Now measure the distance from the camera to the screen. This is the total distance the camera needs to be.

Use the same way to set up the distance for the projector. It needs to project a clear image over all the usable parts of the display screen. Again measure the total distance from the lens to the screen.

Now you have the right distance for both the projector and camera away from the screen (or top).
lafields862 years ago
I too would like to know the suggested distance the motion camera needs to be from the screen as well. Also is there an easy way to add a second camera or are there any advantages in using the Microsoft Kinect camera?
lrubin283 years ago
Cheapest place for Front Surface Mirror is They charge $39 for a real glass FSM sheet, 16 inches x 20 inches. They sell it for high quality kaleidoscopes although people also use it for things like cameras, copy machines etc. They also sell smaller sheets of acrylic front surface mirror - its about 12" x 12" and it only costs about ten bucks - the only issue for optics is that the acrylic is bendable, so it needs something firm underneath, or you should probably just buy the glass version. The glass version also has a very thin layer of a protectant on it so that it can handle very light cleaning. Normally you want to keep FSM in a sealed environment so it doesn't pick up dust.
lfields13 years ago
I have been looking at the idea of trying to use a mirror to reduce the distance the camera needs to be from the screen. Have you tried this? I can't seem to find anyone that has. I would just do it myself but I am waiting on a computer that can handle multi touch. I have all the components except that.
I'm considering building this and I happen to have a broken rear projection TV that has a good front-surface mirror. I've seen other designs on the net that used mirrors to get a larger distance but have not done so myself. If you can get a front-surface mirror, then it should work.
jck112 (author)  lfields13 years ago
I have not tried using a mirror, but your best bet is to use a super wide angle lens - such as one of these:
sifihog3 years ago
Is it possible to wire separate LEDs instead of buying a LED reel?
aismail63 years ago
some one please respond? how manny layers of arcylic do i have to use ?
three see step 5
if you were to do an "Open Air" construction, would there be issues with false readings from the camera from other IR sources? Like say on a stage with lots of different colored moving lights?

I have an idea...
It depends on your method, if you use FTIR, not as much. Other methods like DI or DSI, yes
jcksparr0w3 years ago
do i have to buy the entire reel of ir leds? an entire 5 m/16 ft?
serch3 years ago
Also I forgot to ask ..

On the website posted for the endlighten acrylic
I found three options:

ACRYLITE® Exotic Edge
Green 6F22 GT

ACRYLITE® EndLighten T
Colorless 0F11 L

ACRYLITE® EndLighten
Colorless 0M02 XL (cast acrylic)

Which one is better or which one is the one that works? The higher the transmission they have the better?
serch3 years ago
Hello! I know this is project was done about one year ago. However I was wondering if you could help me out. I am trying to make my own table but I have a few questions.

What is the front surface mirror for?
What is the order in which you place the layers?
Did you put the LEDs on all four sides of the EndLighten Acrylic?

From what I understand the Endlighten Acrylic is placed at the bottom. Then the rear projection acrylic, and then the abrasion resistant acrylic. (Also the abrasion resistant acrylic is to protect the other layers from use right? This would be the layer I would touch?). After this I dont know where the surface mirror goes or what is for.

Thank you very much for all your help and this is by far one of the best instructables or instructions for that matter in building a multitouch table.
I was just wondering, would this work with a sheet of glass as the surface layer rather than acrylic, using the rear projection acrylic and endlighten acrylic layers as you have detailed here?
I am also wondering if it is possible to use glass sheet instead of an acrylic one? It will work as a table so I would like to make it more resistant for scratches by using glass.
Krišto253 years ago
Can you use plexiglass instead of acrylic sheet?
harry5994 years ago
decent pc's are nowhere near $1000, epesily if you build them yourself...
if youre smart about your shopping, you can make a pc capable of high end processing/gaming or whatever you need for just over a grand, where as if you'd buy one pre-assembled it'd be upwards of three grand.
jck112 (author)  harry5994 years ago
I don't know if you are saying they are cheaper or more expensive, but $1000 is definitely a good metric for the quality of PC I am describing. Just try it yourself:
I build my PC for ~600/700€...
It's "High-End" and I can play every single game without lags in Full HD Resolution.
Oh and I uild one time a PC for a friend, it was around 550€ and can to play every game in full hd without any lags.

Just sayin'...
harry599 jck1124 years ago
if you build them yourself, you are looking at about £450-£800, i recently built a high spc pc with an i7 and 8gb of ddr3 ram for around £600-£700.
madfx4 years ago

I made the table, it's all working, im having problems only with win 7 multitouch driver. I installed it, it's ok, but when i unable my mouse the red point are not moving on the screen, it's stuck. I reinstalled the driver several times but im not getting any result.

could someone help me?
madfx4 years ago
I'm having problems to find the led strip infra red. I live in brazil, is there any other way to use the infra red led? could i use like 2 or 3 simple led lamp infra red?

multi touch4 years ago
Was wondering if there is any drawbacks to using a DLP projector, like heat or power consumption. A pros/cons of using either a LED,LCD, or DLP would be nice if anyone has that info.

Excellent info thus far, by the way.
jck112 (author)  multi touch4 years ago
No real cons, you just want to make sure the projector has a high ANSI brightness (>3000 lumens).
I'm sure this will work with any good webcam, won't it?
So why don't just use for exemple a Microsoft Lifecam which you can get for 15€?
ok i saw the older comment where the answer was yes...
A "HD" wecam it is then (for best accuracy) :)
jck112 (author)  the_prototype4 years ago
Higher resolution is better, more frames per second is better. Its usually a tradeoff between those things so we are looking for good resolution (at least 640x480 or similar) and good frames per second (at least 30 - most webcams are only 15).
btw I like your design of the "case" :D
It's ot too big but big enough to store the pc in it so it has only the power cable going out :)
This would be a really great way for stores to get the attention of the people passing by.
DHaworth4 years ago
So, I got the PS3 Eye camera and the IR filter from Peau Productions. Peau productions says the filter will rest on the camera sensor, so don't screw the screws tight, just snug.
My question is, won't this shift cause the camera to be out of focus?
jck112 (author)  DHaworth4 years ago
The IR filter will refract light coming in, so in the end the image will be in focus.
BDubs4 years ago
NEC NP410W Projector price went down
soapdude4 years ago
Could you suggest a projector? Which one did you use? Thanks.
arvindmasti4 years ago
where can we get those types of acrylic sheets???????
1-40 of 118Next »