Instructables
This amazing little shocker is very tiny and can be hidden almost anywhere and give someone a surprise shock! It can operated by almost any 1.5v batteries!

So, on this instructable, I will show you how to make shockers that is smaller than a penny!

However, the biggest disadvantage of this shocker is, it is very hard to build, but it may be easy for experienced soldering iron user (like me) to build the shocker...

Please note that I am only 15 years old and I am not very good at grammar so if you find some parts of the instructable confusing, please let me know and I will try fix it.
And excuse me for some of those blurry and hazy picture. I cannot make them better...


New and improved version!

Build a World's Smallest Electronic Shocker! version 2.5



Disclaimer: This shocker can be dangerous, it gives out 450 shocking volts, so I am NOT responsible if you or anybody are injured or killed by the shocker, the responsibility is yours...
 
Remove these adsRemove these ads by Signing Up

Step 1: Get the things!!

Picture of Get the things!!
P1010071.JPG
Hardly anything is needed for this project but the tools...
  • "Boots" or "Polaroid" type disposable flash camera (You can use a Kodak camera, but they are harder to work with).
  • Some wires (I got mine from broken electronic devices).
  • Solder.

And the tools...
  • Soldering iron with a micro-tip.
  • Desolder pump (it makes everything so much easier, but you could probably get away with out one).
  • Flat-head screwdriver.
  • Wire strippers.
  • Wire cutters.
  • Pliers.
  • Tweezers or micro pliers (or your hand, but you are more than likely to get a solder burn).

Also, if you don't know how to solder, read this great instructable!
1-40 of 1390Next »
MrSteven304 days ago

what kind of transformer is that? please reply

pkalita2 made it!6 days ago
which diod you use
temp_-1725327966.jpg
Hitman31225 days ago

do someone here knows how to make a capacitor charger without a bug zapper or a camera? pls can someone say detail?

tarekh1 month ago

nice

Mr AbAk1 month ago
Nice idea...

can I use the transformer from a bug zapper ?

Those ones are normally 6 pinned transformers, I'm not sure if you can use the same diagram (also, the transformer from the bug zapper is bigger than the camera one). Of course you could use a Bug zapper circuit instead, just change the leads going to the part that you would use to kill bugs to some pins or whatever...

WillE14 months ago

How would I add a push button to this circuit? does this charge then shock you or continuously shock you?

LesPicard WillE12 months ago

Put it between one of the battery wires

Example: cut the 1,5V wire in half and solder the button

i improved,i dont know many volts because i test in my tester and my tester explode
temp_616454458.jpg
Liam.great984 months ago

I made this, and I got about 400v output, but then all of a sudden it stopped working and made a bit of smoke. I looked and it turns out the transformer is arcing over between pins 1 and 2.

AshishD14 months ago

Amazing shocker. I shocked myself eight times, made me go buzzzzzzzzzzzz.

Thanks a lot. Let's ZAP someone.

Student A4 months ago

can I use a 6 pin transformer instead?

note to author and people who dont want to slaughter a camera:

I think i found a possible subsitute transformer here:

http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=MT4135-ND
Plasmana (author)  brooklynlord4 years ago
lol, next time, read the datasheet, it is an audio transformer, not an voltage booster transformer. :)

Im glad you at least tried finding alternatives
as I recall, you have an 'ible on free samples. :)
Shortcircui6 months ago
hey, can anyone help? I made this, but as soon as I power it up, the transistir gets incredibly hot. so much so that the plastic melted. what have I done worng? I wired it uo exactly how it says, so is this irregular operation. and as far as I can feel, the output is non existent.
flagoyo1 year ago
can you connect this to wire loop game ?? where are the line 1 line 2 terminals? please tell mee :)
a new take on the wire game. instead of an audible buzz, you would have an acual buzz. what I would do is put two plates on the handle so when the hand holds it, it completes one break in the circuit. then when the loop touches the wire maze, it completes the second bit
dudes8 months ago
what part number is the transistor from the camera? is it NPN or PNP?
hackeinstien8 months ago

mine only gives 37 v

temp_-683699728.jpg

very good instructable i figured out the fault in mine and its working now

CJ9T52 years ago
could anyone provide a link or tell me what kind of transformer i should buy? i had a look on ebay but all i found was this :http://www.ebay.com.au/itm/13V-Output-220V-Input-4W-5-Pins-Electronic-Component-EI-Power-Transformer-/330820953105?pt=AU_B_I_Electrical_Test_Equipment&hash=item4d06772411&_uhb=1#ht_2183wt_1141

try TTL FLASH TRIGGER TRANSFORMER

Ohcpin2 years ago
May i know volume and code for capacitor, diode and transistor?

transistor is d 965

lieg1 year ago
can YOU write mane or number for the Transistor. thmx EMAIL marek.milak@seznam.cz
hackeinstien lieg8 months ago

d 965

spirit x1 year ago
can i use a transformer from a mobile charger. please reply
dudes spirit x9 months ago

you could, however a mobile phone charger usually will only multiply the voltage by 10-25 times while the transformer he is using does 300 times.

egor777119 months ago

good idea!!!

temp_-335368761.jpg
spirit x1 year ago
can i use 47nf capacitor istead of 22nf
JacerP31 year ago
Hello! Could some help me figure it out how to make this shocker "less powerful" by discharging, lets say, 50V instead of the 400-450V? How do i do it? Should i simply increase the value of the resistor? Or should i use a different capacitor too? Thank you!
ionutz351 year ago
ce valoare are tranzistorul?
Hi Plasmania - I think there may be an error in your circuit diagram that may explain some of the complaints. Every component pinout I can find shows Transistor 'Base' to be the middle wire. (E-B-C, rather than E-C-B). If that is the case (and assuming the photos are correct) Transistor Base is connected to XFMR pin 1, and Collector is connected to XFMR pin 4 That also keeps the Base on the 1.5 V side of the circuit. I tried to upload a revised schematic, but that doesn't seem to be working...
these transformer has any value
gsgkill1 year ago
Could make a good mouse zapper. If it's 250 volts @ 1.5 volts What would a 9 volt battery do? Do you know the approx current? Is the cap a discharging cap? The discharging cap could be reduced to prevent a burning ark? For use in Dogs (as in lets not mark our territory there anymore boys)?
j3rz1 year ago
Hello, I'm new to electronics and I was taking a look at your circuit trying to figure out how it works. If you don't mind I would like to know what is the purpose of the 220 ohm resistor. Thank you.
kbyrd21 year ago
I recently made 8 of these and put them in parallel to charge a capacitor bank. Now, when using one to charge a capacitor I require an RC Circuit. But, when I made the 8 in parallel no resistor was need to charge a capacitor. I was just hoping you could clear up how I could have built up the resistance to not require a resistor to charge.
ffp1 year ago
Mine doesn't work, it gives 1.5V output. I'm using a 500 ohms resistor since the one that came in the camera was 1k
1-40 of 1390Next »