Instructables

How to make a homeade Airsoft Gun from a Nerf gun

Step 9: Thoughts and Suggestions

Picture of Thoughts and Suggestions
Here is a couple of suggestions sent in by fans.
I take no responsiblilty if a spring pokes out your eyeball.

To add extra power with springs
From invisiblelight386:

first unscrew both guns. take the spring out of one of them. now take the other gun and remove the plunger, toob thing and the barrel that holdes the darts. the plunger should already have a spring on it. remove the trigger lock on the plunger and slide the other spring on put the lock back on (this might take a wile). when the spring and the lock are on insert the plunger back into the toob. reassemble the gun leaving out the dart barrel. now take a bic pen and remove the ink. cut off the top black stopper. spray DW40 or any other silicon lubricant into the pen. pinch one end of the pen and insert in to the ovle thing at the end of the toob. now there are two things you can do: 1. fill the front of the gun with expandable foam. this will hold the pen in place and muffle the sound. cover the front with duck tape. to fire insert the bb then cock it (the first couple times it wont go very far because of the lubricant). you can take a very smal pice of cotton and stick it into the barrel to dry out the lubricant.

also the more springs you put in weakens the trigger lock and can fire unexpectedly. so becarful. i shot myself to test how much it hurts from 5 feet away and it inloged into my hand. THIS IS VERY POWER FULL.

Heres a good idea from KnextGeneration:
To increase accuracy of bullets, enlongate the barrel. This is true for all guns. For pen barrel guns though, it is hard to line up 2 pen barrels right next to each other without one aiming in a different direction then the other.
KnextGeneration's idea was to take a pen grip, the rubbery things you put on pencils or pens to make the grip more confortable, and put half of it on one end of a pen, and half on the other. This way, you know that they are aligned. You may want to tape both ends of the grip on the pens, and maybe add a long knex piece for strength. Before long, Youll be making sniper rifles. If only pen guns and shoot at 1000 fps. sorry, daydreaming. anyway thanks for the tip, and good luck on making these.

There were also some questions about measuring fps. theres basically 2 ways to do by yourself.

1. Get a friend to get a stopwatch. Shoot your gun at a target 20 feet away, to give you friend a chance and starting and stopping the stopwatch at the right time. Take how long it takes, for example .25 seconds. Take 20 feet divided by .25 seconds. 20 divided by .25 is 80. that means the bullet traveles at 80 fps.

2. Get a gun you know the fps of, like a friends airsoft gun. Shoot that at a wall far away and time how long it takes. Then shoot the homeade one. If they are the same, they have the same fps. If it take the real airsoft gun a short time, the homeade one is less. If it takes more, well, you get the picture.
You can also shoot a real airsoft gun at a piece of styrofoam from about a foot away, and then shoot your homeade airsoft gun at it the same distance away. Use and exacto knife to cut the styrofoam down the side and find the bullets.

example: if a 300 fps airsoft gun shoot in 10 inches, and you shoot your gun and it goes 5 inches, your gun probably shoots around 150 fps.

hope this helps. -Perjak
 
Remove these adsRemove these ads by Signing Up
Stratles24 years ago
why doesnt everyone just buy a real airsoft gun
because those who convert the nerf guns actually have a sense of imagination
TehDuckzor3 years ago
Unless youre poor or want a unique gun on the battlefield, i suggest buying an actual airsoft gun. My TAR21 shoots 460 FPS...
Unless you're going to throw $200 on a plaything, I suggest investing in a cheap nerf gun and converting it.

Seriously, if you want to brag, do it where someone cares.
cranberys4 years ago
 how do you take out the air restricter other than that good job but my mom or dad will suspect sumthin if i ask for bb's (im only 10) 
Lucky for me my dad owns a gunshop and I own 4 bb gun science I was 8 so I tell my dad "I'll be out back if ya need me" and he's like okay and he doesn't really care intact I just made a very interesting crosshair type system for one of my bb guns.... As for the air restrictor it ususally involves opening the nerf gun up... I have done this but it depends on what gun you have... Soooooo. Yeah
another thing: take the air restrictor out. I modded my nightfinder (im goin to mod it with double springs) sorry if that was already said in the mods up above I skimmed it
I find it really hard to unscrew nerf guns these days.
Ironman975 years ago
Mine shoots at 200 FPS!
AustralLord6 years ago
do not stretch the spring! it actually makes your gun better for like 10 shots, but then it becomes EXTREMELY weak. oh, and thanks for the fps tip, i need to see if my gun lost power over time.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!