Instructables

How to make a Traffic Light Subwoofer.

Featured
Picture of How to make a Traffic Light Subwoofer.
Please DONT steal the traffic light&. As a driver and a pedestrian Im telling you there put to better use directing traffic then shaking you house or car with the music of your choice.


But lucky for me I found a small red light in my next-door neighbors garbage. Its small but it will work until I find a full size traffic light. At which time I will post another instructable.

What you need.
1 Plexiglas or wood
2 traffic light
3 speaker - 1 or three depending on what type of traffic light you are using.
4 speaker wire
5 speaker inputs

(electric cross over if necessary)

 
Remove these adsRemove these ads by Signing Up

Step 1: Clean.

The first thing you want to do is clean the light up& after all its probably been sitting outside collecting dust for some time.


No picture necessary&

Step 2: Deal with that Plexiglas.

Picture of Deal with that Plexiglas.
cut out your Plexiglas so that it will fit into your traffic light. it doesnt have to be perfect because it will be glued later on so that it is almost air tight.

Next cut out the circle for your speaker. use a compass, installing the speeker properly is important.


finally place the speaker into the hole you've created and glue. (no screws)

Step 3: Instaling the speeker..

Picture of Instaling the speeker..
DSCN0003.JPG
First connect the speaker to the inputs or the electronic crossover depending on how your connecting your sub.
now glue the input circle to the light case and make sure you have a good seal.



Step 4: Insert time

Picture of insert time
Place the speaker and the Plexiglas into the case and glue. Make sure you have a good seal then let it dry.

Step 5: Finishing up

Picture of Finishing up
DSCN0006.JPG
Close the box (real tight) make sure theres no loose parts on the box and plug it in..

Step 6:

Picture of
It doesnt sound good; but I like the look of it when its on behind the red glass.


Things to do in the future - add light
Sharp_Tack2 years ago
AWESOME!!!!
Vinsu3 years ago
Reverse polarity of the speaker and add reflextube/airvent to the frame, would sound much better I think...
ilpug Vinsu2 years ago
+1
Vinsu3 years ago
Strong epoxy or glassfiber resin (don't know if correct word) would keep atleast a small speaker element in place.
nmesis_024 years ago

Taychon is right. One thing you could do to help is add one or more ports (usually two will be enough). This will increase the efficiency of the system if done correctly. Otherwise you could just have the speaker faing outwards from the remaining walls of the enclosure. 

Great idea though 

israel.prz5 years ago
Why "no screws"?, I think them should hold better the speaker, don't you?
bmlbytes5 years ago
To add light you could use a speaker like this one. Although you may want to try to find a red one instead.
bobobob12305 years ago
it does look cool, maybe drill a few holes around the outside of the light?
you could flip around the driver and have a better but less ascetically pleasing cover in the rear. you could even add lights that way using the current to the speaker.
erie945505 years ago
For the people in the the bay area, San Jose has a shop called weird stuff that sells used electronics and they have a bin has used traffic lights.
Tachyon5 years ago
You said it sounds bad. No doubt. There are some things to consider/try. - cabinet volume. All woofers work best when they are matched to the cabinet they are in. Do your best to estimate the volume of the traffic light enclosure and then buy a speaker with a 'Q' that matches that volume. - Sound projection. Where is the sound supposed to come out? I wouldn't drill holes in the light, that ruins the look of the project, and then what would be the point? Instead, why not put a port in the back of the unit? Again, use the speaker manufacturers specs and or online tools to match the port diameter and length to the frequency of the speaker. - Cancellation. Make sure that the front and rear of the speaker are sealed from each other. Otherwise the soundwaves from each face of the speaker cancel each other out and reduce volume. If it's bad enough, this can even destroy your speakers or amp. - Vibration and resonance. You may need to put some baffling into the body of the light. Some insulation might not be a bad idea either. Also, remove any weird projections inside the case. - Crossover. Make sure to use a crossover with a sub. Keep high frequencies from being sent to it. Either use the one in your amp (if it has one). Scavenge one from an old speaker/sub, or build one. They're simple, cheap and easy to make. Please update this if you make any more mods or find a bigger stoplight.
Rossiroller5 years ago
Buy them at flea markets! I got one there for 5 bucks... The guy that sold it to me was mad because I had him hold onto it for an hour so I could check out some other stuff, and he said people were offering him like 40 bucks for it.
sweat but put some L.E.D's on it and other lights like green and yellow plus an ipod hook up with a clock on the bottom. Ahhhhhhhhh dream stereo!
nobody3945 years ago
Throw in some colored LEDs and maybe a switch that goes through the colors and a have two stacks of red yellow and green oohhh and a pipe going through them and hang it on ur wall that would be sick
sonic_dan5 years ago
now you need two more so you'll have red, yellow and green, stacked. now THAT would be awesomerer...
awesomerer?
Sometimes in the US, traffic lights have a larger red light than they do green and yellow. Perfect for speakers.
evanwehrer5 years ago
Where can I get a traffic light?
I got mine from a theme park that used it on their Go-Kart track. They switched to an electronic throttle control and the light had just been sitting in storage. Might be a good place to start looking.
svenson5 years ago
This is great, I've actually got a full traffic light exactly the same as this and have been looking for something to do with it.
crearc5 years ago
Add some LEDs in there...that'd be sweet.
ikoda5 years ago
Make the red glass removable. Have it open up like a door.
amdsk8r (author)  ikoda5 years ago
take a look at step 4. There all ready is a door.
ravebot5 years ago
woooooops i thought you said steel them oh well now i have lots
ravebot ravebot5 years ago
steal sorry
I like it, maybe try putting lots of small holes in the plastic cover, should make the sound better when it's on.
amdsk8r (author)  killerjackalope5 years ago
the red glass is like 1" thick "glass". so it would hard to drill through.
Ah right, the newer ones I've seen lately are a bit more flimsy in comparison...
LinuxH4x0r5 years ago
Nice, but it still needs some work. I'd love to have these once they get a little more refined. 4/5
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!