Picture of Imac G5 DIY capacitors repair
There are probably enough DIY manuals on how to replace those bad capacitors
in the G5 imac model...
If not then this will maybe help..

If you're Imac G5 is suffering from power problems (not turning on, standby issues, video problems and scrambled pictures. Maybe its time to check those capacitors on the motherboard)

Checking those caps is easy and takes 2 minutes: Follow step 1 and 2, and step 7 and 9 to know what to look for...

Step 1: The Imac...

Picture of The Imac...
The Imac G5 was was plagued with the Capcitor problems, Apple started a special warranty program to repair all those Imac's. That program has bin terminated, but I have seen the same problem with the timecapsule as well. Today there are not that many people that want to repair there imac G5 but for those, here we go...

Our victim: A "left to die" Imac G5 17." We are going to save him in a Saturday afternoon.
Here are some things we need to help him:

A LOT of space...  We need to store all his parts temporary and we have to work on its motherboard.
It also keeps things organized.

Tools: These are the tools that I used:
soldering iron, screwdrivers, torx screwdrivers, anit static band, pliers, thermal compound, and replacement capictors.
Experience: Please have some, Its not difficult, but I think some is defiantly required.

Safety warning: Always unplug the power!! Even when the power is unplugged some capacitors will remain there power! In the new Imac models these power supply units on the bottom are open, and you WILL get a high voltage shock from it!! This is not the case here but be advised, if you see something and you have no idea, just stop and ask someone who does knows!

Capacitors: The ones that we are going to replace are bulging and could spit out electrolytic fluid or residue. (In fact, mine did when pulling them out...) Clean of this stuff from youre hands and the motherboard immediately!!! And wear safety goggles, the old capcitors are under heavy pressure, if they burst right in your face then... Well, youre not becoming any more attractive from it...


Can someone send me a link with the capacitors on amazon.com or ebay?

I dont know which buy, so i need help.

Noddes3 years ago
Hi Has anyone changed caps to cure a video fault ie machine operates fine but monitor shows predominately green /yellow odd time will operate ok but soon slips back to this mode. I am willing to make a full replacement of caps as per EWOUT 's instructions but don't want to strip it down if it does not work. The caps show no sign of bulging or leaking. Thanks for your replie(s)
ewout (author)  Noddes3 years ago
Well, if you did see the top bulging or leaking electrolytic fluid on those caps then it would be easy to tell if it would work, if not then the only way to know for sure is to take them out and replace them. For those who cannot measure caps its the (only) cheapest way to tell... you have to get your hands dirty....

ashiekh3 years ago
Radio-Shack make a very nice soldering iron that has a hollow tip, and this makes it much easier to heat the leads all round, and it is probably best to replace all the capacitors at the same time, as those that look sound are probably soon to fail anyway.

The power supply probably needs recapping at the same time.
dcain13 years ago
I need my PSU fixed but am fearful to do it as i have no experience. could i pay you to fix my unit? dancain @ gmail.com
ewout (author) 4 years ago
I want to thank you guys for still leaving comments even after one year...
Iam happy to see that a lot of people are using the instruct to repair there broken imac's, giving them a second live.

Many thanks to you all...
captain3d4 years ago
I managed to re cap an imac G5 today using this guide and it is now up and running installing a new system. Made me happy.

My old, little soldering iron was not up to the task as it could not deliver enough heat to release the old caps. I bought a 140 watt solder gun and still had to hold it there for 10 seconds to get them out, but it worked.

I heated the the blocked holes and pushed on the new caps and slide them in one leg at a time until they were seated. Then again gave them a good blast and another drop of solder with the solder gun.

The one thing I missed was refitting the left grey piece (inverter unit). I had connected the two cables but missed the four pin socket as I had not seen that on the dismantle. Once refitted correctly the machine seems to be up and running.

kallisti54 years ago
To be honest, you can use capacitors of a different voltage in a pinch, as *long* as the new ones have a higher voltage tolerance then the old ones... your biggest problem from this will be the physical size difference.

You however *MUST* use caps of the same capacitance (eg 1800uf == 1800uf)
kallisti54 years ago
Great guide, I am going through this process at the moment as well.

Keep in mind your PSU may also have quite a few popped caps, if you are more skilled I would check it out as well.

For the PSU, gently scrape the gray epoxy away from the bused caps without scratching or bending the coils.
Data6434 years ago
Wow. You won't believe this. My friend found one of these iMacs in a dumpster last week. He couldn't get it to work (boots with idle screen) so he gave it to me. I think that the caps are faulty. I read on iFixit that there was a stream of bad caps around the time that these iMacs were produced. Anyway, i'll give your method a shot.
Agent244 years ago
Yes you must use 105°C rated capacitors but not ANY capacitors.

They need to be good brand, Rubycon, Nichicon, Panasonic, Sanyo etc and also must be the correct series to ensure they have correct ESR and Ripple current rating (Check the datasheets of the old and new capacitors)

Also, do NOT use a drill to clear VIAs, you can very easily destroy the plating and ruin the board.

If you must use something, the BLUNT end of the drill, while applying heat to the joint and push the solder out.

Do NOT drill using the sharp end while the solder is cold.
techwreck5 years ago
goo gone, or rubbing alcohol does the job. if you want to polish it. Use a 1:1 mixture of rubbing alcohol and lemon juice. works all the time.
Kasm2795 years ago
You might want to re-word this "Dont get in youre eyes or wear safety goggles!!!" to something like "So you don't get it in your eyes, wear goggles!" It sounds like you are saying either don't get it in your eyes or don't wear goggles o.O
ewout (author)  Kasm2795 years ago
There is always room for improvement, I made some changes for you... Hope you like them.. I must point out that English is not my mother language but I try my best...
gspiderman5 years ago
Can you recommend a good place to buy the kit?
ewout (author)  gspiderman5 years ago


But iam not sure what to do with 25 caps?

Same thing here:


I think you should order those things separately and not as a kit, its probably the most cheapest way to do it. Just take same values and if your budget permits it: Take caps that can take a bit of heat to prevent this from happening again!!
Asmodeo5 years ago
Really nice instructable!!!
It gave us the opportunity to see a "naked" G5 As well !!!

I've changed capacitors in PC motherboards a lot  of times, and the tricky part is desoldering the old ones.
I have a method:  Use a 60Watts soldering iron, applied to BOTH legs of a given capacitor at the same time.
Let It heat for 10 seconds.(It´s a bad capacitor...You can't ruin It!).
Then, SLOWLY, pull the capacitor out of the board while applying heath.
To open the pad orifice where the capacitor lead was , use the copper "tail"....it is a hard way, but It is worth the effort.
If the orifice doesn't clean at your satisfaction, then use a drill bit of the right size (0,5 mm is ok ) ..but use it BY HAND..make a handle for it with some isolating tape!

One thing I do not agree with You is: "put same rate capacitors"
The "capacitor maladie" is due to capacitors that are rated up to 85°C of temperature.
I  always use as a replacement capacitors of the same rating in microfarads (uf) AND volts , but capable to withstand 105°C  of temperature.
The difference in price is negligible.

Thanks again for the photos.

I'd be extremely careful using 60 watts for 10 secs.
Don't worry.
I've used it for almost a minute and no pun for the traces of the motherboard.
You must realize that you are trying to unsolder a BAD capacitor (You can't ruin It MORE) and It's soldered onto the positive and negative huge planes of the power supplies....It's A LOT of copper that will dissipate the heat and , if You use less than 60W this will be a real problem....You risk of pulling a capacitor's leg that is yet well attached to the internal pass-trough-holes copper due to a "cool" soldering tip. Bad thing, I prevent You...
I have, once , used a 100W soldering iron (from a friend) and...well.....each damaged capacitor was out of the board in less than 5 seconds!!
Last sunday, I used a "solder sucking" device (I don't know how It's called in english), along with the 60W soldering gun....I was able to "unclog" the orifices in a matter of seconds.
I used a new approach to hold the mother board:
I made a "vise" with two 10inch "L" shaped plastics, almost 10 inches long, too, attached to my table with grips, and sandwiched between them the motherboard with two pieces of foam.
The board remains vertical, firmly held by the jig, and then You can use both hands, one for the soldering gun, and the other to pull softly the capacitors out, or to use the "solder sucking" device", one from each side of the board....I think I will make a permanent jig for that!!!

Nice year for everybody!

Yeah I was just thinking of that all that heat near the PCB, I've been in some tight spots and burnt some pcbs with less. But I'm going to try and get some working caps off a video card later so I'm definatly gonna try some higher heat levels after reading this, only got 40 watts to work with but we'll see.

And that solder sucking device, I know them as desoldering bulb or pump depending on the type. But in a pinch you can also make your own solder braid  with some copper wire and flux to wick away old solder.

Anyways good luck to you Asmodeo!
ewout (author)  Asmodeo5 years ago
Thank you for your comments Asmodeo, If you don't mind I have pasted your info into step 7. Your right about  using a 60Watts soldering iron, Unfortunately I don't have one right here. And what I didn't test or confirm, I dont put here.

I agree with you about using higher temperature caps, because that is one of the reasons why we are replacing those caps in the first place.
Asmodeo ewout5 years ago
You're wellcome, ewout !!

milsorgen5 years ago
 lol glad apple users get to experience the joys same as us pc users

though i havent run into this issue since i was running socket 7s
dogboy124575 years ago
Thank you very much for this Instructable. My IMac at home broke same problem. I have had this happen once before. The guys at the shop looked at it and said it was going to cost 600$-700$. I figured it was going to brake again so i should just get a new one. Found this and fixed it. I didnt even think about doing it myself. you saved me money. It also happened to my uncle. He gave it to me. been lying around in my basement. I am going to fix his computer too. So I will have two IMacs thanks to you.

Again thank you.
ewout (author)  dogboy124575 years ago
Your welcome Dogboy...  Your excally the reason why I made this instructable.
Good luck repairing your Imac(s)...
ewout (author) 5 years ago
I have updated the instructable with answers from your questions. And made things a bit more clear. Thanks for your comments...
omnibot5 years ago
Great instructable.
The capacitor plague is a source of frustration and wealth to us all ;) I personally ow my flatscreen to this disease and a dead flatscreen is just as easy as with the iMac.
hemmikarl5 years ago
GREAT instructions on how to replace these capacitors.
although i don't need them many other migth need them
lemonie5 years ago
This is very well shown, how do you identify the cap's that need to be replaced?
(some dodgy-spelling, might benefit from a re-read?)

with electrolytic capacitors its usually the top bulging or leaking electrolytic fluid
on the other hand ceramic and polyester capacitors is not easy at all to identify whaich are broken
It's usually rather obvious, they'll be leaking the electrolytic fluid that's normally inside, or bulging.