Introduction: K'nex - C.A.R Instructions

Picture of K'nex - C.A.R Instructions

Hey guys, and today I bring you the C.A.R (Compact Assault Rifle). But before we go any further, I would like to thank and give a lot of credit to Instructables member Dr. Richtofen since I used pictures of his own C.A.R. Also because he never had the chance to make instructions, I myself have made instructions for it so you can have your very own C.A.R. The Compact Assault Rifle took me 5 hours and 40 minutes to build it and this does including making minor tweaks and adjustments to it and by the way, this gun does remind me of the SMR from COD: Black Ops II which was based of a prototype called the Saritch 308.

Good Points

· Removable Magazine

· Comfortable Hand Grip

· Very Futuristic

· Movable Charging Handle

· Good Iron Sights

· Magazine Release

Bad Points

· Doesn't Shoot Because It's Just A Model

· Uses Quite A Lot Of Cut Pieces (See Parts List)

Also check out my other creations and instructions

Step 1: Parts List

Picture of Parts List

If you have any trouble or need more pictures just leave a comment and I will get back you ASAP. I strongly advised you to collect all the pieces before you start building. Also I have added a few notes throughout this instructable to make it more easier to understand something if you run into any difficulty.

Green Rods - 291

White Rods - 93

Blue Rods - 23

Red Rods - 3

Green Connectors - 18

White Connectors - 11

Blue Connectors - 14

Yellow Connectors - 122

Red Connectors - 42

Light Grey Connectors - 11

Dark Grey Connectors - 51

Orange Connectors - 36

Tan Connectors - 2

Tan Connectors (with the little tab cut off) - 1

Y Shape Black Connectors - 29

Black Socket End - 1

1.8cm cut Rods - 16

3.1cm cut Rods - 6 (These can be replaced with a blue rod and grey connector)

Orange Connector (cut, see step 4) - 1

Hinge Black Half - 3

Hinge Blue Half - 3

Black Wheel 25mm Open Centre - 4

Push On Grey Gear - 2

Rubber Bands - 9

Total - 792

Step 2: Stock, Magazine Well & Release

Picture of Stock, Magazine Well & Release

Step 3: Handle Part I

Picture of Handle Part I

Step 4: Barrel, Trigger, Foregrip & Handle Part II

Picture of Barrel, Trigger, Foregrip & Handle Part II

Step 5: Charging Handle & Handle Part III

Picture of Charging Handle & Handle Part III

Step 6: Magazine

Picture of Magazine

Step 7: Done

Picture of Done

Well done you made it to the end, I do hope you have enjoyed building it.

Thanks for building it, please leave a comment in the box below and subscribe


dynamite_kid (author)2017-12-01

im gonna mod this to make it shoot

Ok Dynamitekid

MonkeyKnexer15 (author)2017-03-18

I made it once, but the mag did not want to stay in. got anything to change that??

Not really sorry, I just ended up putting a blue rod on the white connectors though the magazine itself to hold it in place, thats all I can really say.

master-splinter306 (author)2015-07-09


Thanks Mastersplinter

No Problem Zombiekiller-93

Hey Mastersplinter, if you like any of my creations then I would appreciate a comment, favourite or even better both of them.

I just favorited it!

Thanks Mastersplinter

I will favorite this one RIGHT know as I am saying this.

CorgiCritter (author)2015-02-14

I looked it up, and this does indeed look like the SMR in COD. Good instructions, and the front grip looks amazing. This definitely earned a favorite.

Thanks Corgi, when I first saw the C.A.R it reminded me of the SMR

sandroknexmaster (author)2014-07-11

Looks good!

It does, doesn't it ;););)

Have you by any chance Richtofen have manage to rebuild it again

I've had chances enough, but haven't done that, hahaha.
I still have some thing that I've had for a while now, haven't got around to posting it. Maybe I'll rebuild this one after I do post it. Video games, college, music and guitar playing distract me too much from that, though... :3

That's ok, just take you're time as there is no rush. Just wondering what are you planning on building next?

Thanks Sand

You and Dr Richtofen have both done an excellent model well done

www139 (author)2014-08-15

Nice job you made it to the finals! ;-)

Zombiekiller-93 (author)www1392014-08-16

Thanks, was not expecting to get this far in my first contest

hunter999 (author)2014-08-15

Congratulations on being a finalist!!! :D

OMG, I was not expecting that. Have you check out my Peacekeeper

akshat21045 (author)2014-07-18

Cool! I always wanted instructions for these!

That's ok Akshat, I will be making instructions for another one of Dr. Richtofen's creations and it will be posted at some point in the middle of August this year but I will let you know when I have posted them.

nerfrocketeer (author)2014-07-11



nerfrocketeer (author)2014-07-11


Thanks Nerf, really appreciate it

JonnyBGood (author)2014-07-11

Looks great! Good job!

Thanks Jonny

dr. richtofen (author)2014-07-11

Heh, finally there are instructions for this thing :p
Looks like everything is right, good instructions. Nice job!
I'll try to rebuild that little bolt release I had in mine, and give you some pictures if I succeed. For the people that would be interested in that little thing.

Thanks for making the instructions!

Thanks, glad you like it. I'am going to be making instructions for another one of your creations but I won't tell you which one it is. I will be posting it at around the middle of August.

About This Instructable




Bio: Hello there I'm Zombiekiller-93 but me can call me Jay. I like making models of K'nex guns from the Call Of Duty games ... More »
More by Zombiekiller-93:K'nex - CZ-75 InstructionsK'nex - Biplane InstructionsK'nex - MP5K Instructions
Add instructable to: