Step 6: Hammer

You're nearly finished! Just make the hammer: It's easy.
This is a cool design! I have an idea that I might use to make it whack the ball even harder and up a higher track by using some of my modified motors which plug into a wall outlet and spin two to three times faster than any other knex motor! :)
i made the project and it works great i never thought that the small engine would never pull that hammer all the way around. i wish you would show how to make the rest of the track.
I can't add a pic now, because I use the lift on a other way: as transport. The ball gets now hit by the arm, and flies 1M trough the sky, and ends up in a basket.
Can you post an instructable on how to modify that to fling the balls that far? I'm definitley going to build this and use it in the new ball machine I'm going to start tommorow! :)
I just see, it isn't 1 mile, it's 1 meter :-P. It's easy: Build this instructable, and don't add more track then shown in this Ible. Just cut the tubing off after the short part shown here, and let the balls fly! If you put the lfit also a bit higher up (so add a red box underneath it i.e.), it will go even further.<br><br>So, don't modify, just don't add any more rubbish after the lfit!
in the last step have I put some tips how to make the track. I think you can build your own with that.
Might build but heres 3 questions....<br><br>1. Do you have to have that pathing, can I change it to some different pathing?<br><br>2. I have the motor in the picture (Ignore ball) will it still fit in?<br><br>3. The motor isn't too powerful, does it have to be a strong motor?<br><br>Thankyou, MM8
1. It's changeable to yellow 5 - way connectors, although you'll have to find out the new height of the track.<br><br>2 + 3 Attach the motor to a white snowflake connector, and change the spacers/rod. The motor should work, cause my motor is weak too. If it doesn't work, just gear it more down. (again a blue gear on a red, you could change the red gear into a big yellow one, but the motor must be on a different place then0
Aww man.<br><br>Don't have all the spacers :(
i have like 300 blue spacers and 400 silver spacers!
and i'm getting sick of having so many spacers...
you want to buy some??
Im lright know I bought 55 blue ones and have about 65 silver
Try to get more ones!
I am!
KK will build soonish
Do you have to have the orange tubing connectors, I have none<br><br>Ps: Please reply ASAP
Read 2 comments below. There's your answer :-P
Oh yeah forgot!<br><br>Sorry
I decided to make this and it works great. Although I did have 1 problem with it letting only one ball in at a time.
A very innovative lift design, I must say. Does it automatically reset itself too?
Yes. It works as long as the motor runs.
I built it and what happens is the hammer comes down but stops short of the ball, then comes down slowly. Also, the gate opener keeps breaking when the hammer lifts the thing up. Please help!<br>
Hammer comes down but stops short of the ball??? Could you give me a picture of that, I never had that problem<br><br>Gate opener: did you make the 2nd and the 3rd picture of the last step? that should help. It works even better if you remove the blue connector and the blue and gray spacer on the white rod.<br><br>If you've more problems, tell me.
So could the track go vertical?
I never tried that one, I'm sorry.
Ok, maybe a test for me sometime
Please tell if that's possible (if you sent me pictures, I'll add them to this Instructable)<br>
Oh, its a good design, a similar thing could be made, but the track goes vertical up?
No. Like you see in the picture, the track goes 30/35 degree up, but it has a other use: transport. Just cut the tubes off direct after the &quot;launch&quot; part (the part in this tutorial), and the ball flies about 1M, where it must be saved by a basket.
Is the end of the hammer really heavy, so it comes down faster?
yes, it's heavy: but not too heavy, otherwise the engine wouldn't pull it all the way up.<br>
What makes it come down real fast? (the hammer)
Gravity :-)
Sorry but I don't have a lot of KNEX. My birthday is soon and this is number 1 on the list to make. You literly inspired me to make ball machines so you get V.I.P. on my list!
I can't make it but it looks awesome!!!
Why can't you make it?
not bad and really cool
the little thing with the spacers looks like a face
If you hold your mouse on the photo, I said it is a smiley face :-).
Is anyone going to built it? Please tell...
I might use it in a future machine.
What is a future machine???
My next machine
He means one he makes in the future ball machine :-)
What's the music in the video? :)

About This Instructable


7 favorites


Bio: Hi! I'm Ruben, better known as RNB. I'm a student Mechanical Engineering and hence like to build contraptions related to that. I mostly ... More »
More by RNB: K'nex Bending Rod Launcher The Official Guide for Building Knex Ball Machines Ventus - K'nex Eurofighter
Add instructable to: