Introduction: K'nex Helicopter

Picture of K'nex Helicopter

This is a easy but fun helicopter to build. Perfect for all age groups and all skill levels.

Step 1: What You Will Need

To build this helicopter, you will need:

6 blue connecters
36 grey connecters
6 white connecters
4 green connecters
2 red connecters
7 yellow connecters
8 orange connecters
6 singular connecters

3 white rods
6 green rods
6 blue rods
17 yellow rods
26 red rods
18 grey rods 
2 orange, bendy rods
2 green, bendy rods

2 red triangles
2 yellow triangles

20 grey spacers
1 blue spacer
3 ender pieces

1 motor

Step 2: Step One

Picture of Step One

In this step you will need:

4 blue connecters
8 grey connecters
4 yellow connecters
2 white rods
12 red rods

Step 3: Step Two

Picture of Step Two

In this step you will need:

4 grey connecters
1 white connecter
4 red rods
4 yellow rods

Attach like shown in picture two.

Step 4: Step Three

Picture of Step Three

In this step you will need:

18 grey spacers
4 singular connecters
8 grey connecters
2 grey rods
8 yellow rods
5 red rods

Attach as shown in picture 2.

Step 5: Step Four

Picture of Step Four

In this step you will need:

2 yellow rods
2 blue rods
2 grey connecters
1 white connecter
1 yellow connecter
*2 yellow triangles
*2 red triangles

*3 or 4 red triangles may be used instead of the yellow triangles and the gap (only if you have the pieces).

Attach as shown in picture two.

Step 6: Step Five

Picture of Step Five

In this step you will need:

1 red rod
2 bendy, green rods
2 bendy, orange rods
6 grey rods

Attach as shown in picture two.

Step 7: Step Six

Picture of Step Six

In this step you will need:

2 singular connecters
2 grey rods

Attach as shown in picture two.

Step 8: Step Seven

Picture of Step Seven

In this step you will need:

2 green rods
2 grey rods
2 red connecters

Attach as shown in picture 2.

Step 9: Step Eight

Picture of Step Eight

In this step you will need:

2 blue rods
2 yellow rods
8 grey connecters

Attach as shown in picture two.

Step 10: Step Nine

Picture of Step Nine

In this step you will need:

4 green rods
4 grey rods
4 green connecters

Attach as shown in picture two.

Step 11: Step Ten

Picture of Step Ten

In this step you will need:

2 blue connecters

Attach as shown in picture two.

Step 12: Step Eleven

Picture of Step Eleven

In this step you will need:

1 white rod

Attach as shown in picture two.

Step 13: Step Twelve

Picture of Step Twelve

In this step you will need:

1 white connecter
4 red rods
1 grey spacer
1 ender piece

Attach as shown on picture two. Order from inside out: Grey spacer, blades, and ender piece.

Step 14: Step Thirteen

Picture of Step Thirteen

In this step you will need:

4 orange connecters
2 blue rods

Attach as shown in picture two.

Step 15: THE FINAL STEP!

Picture of THE FINAL STEP!

In this step you will need:

3 white connecters
4 orange connecters
8 grey rods
1 yellow rod
1 grey spacer
1 blue spacer
2 ender pieces
1 beige piece

Assemble in this order:

Attach ender piece to one end on the yellow rod.
Insert through motor
Place the two spacers at the open end of the yellow rod.
Place beige piece on so the pin points to the direction of the open end.
Place blades on.
Cover the open end of the yellow rod with an ender piece.

Place as shown in picture four.

Note: Motor can be facing either way

Viola! You have just made Pengu_333's K'nex helicopter!

Comments

RMConstruction (author)2011-12-30

Are. You. Freaking KIDDING me?!

Pengu_333 (author)RMConstruction2012-01-18

Good or bad " are you kidding me?"

Lol calm down.

The Chunky Sniper! (author)2011-12-30

Have you two gone mad?
Awful, just awful.

dr. richtofen (author)2011-12-30

It has an ok shape, maybe try filling it in. If I'd could rate, I'd rate it 3*

mikeasaurus (author)2011-12-30

Clear pictures and direction. What's your next build going to be?

About This Instructable

1,695views

1favorite

License:

More by Pengu_333:K'nex Helicopter
Add instructable to: