Introduction: Knex Pistol

I was throwing random k'nex pieces together when I made something that looked kind of like a body for a gun, and then I had a pistol. Now about the pro's and con's...

Pro's:
Looks good
True Trigger
Comfy handle

Con's
Single shot
Not good for long range shots (Shoot 25-35 ft.)

Step 1: The Body

This is the hardest step, but it's pretty easy. Just follow pics and READ ALL IMAGE NOTES or your gun won't work.

Step 2: Trigger

This piece is necessary to the gun. Once again, READ ALL IMAGE NOTES!

Step 3: Panels

You're almost done. Just add on these panles and read all the image notes.

Step 4: Ramrod and Rubber Bands

Comments

author
Indestructibility+Man made it!(author)2013-08-25

This is my version of your gun, I changed the trigger to a more reliable design and added an 8 shot mag

photo-2013-08-25 7:59 PM.jpg
author
FlutterTree made it!(author)2010-11-28

What?

author
NatNoBrains made it!(author)2011-01-31

He rated it 4.5*

author
FlutterTree made it!(author)2011-02-01

Oh OK

author
jmtb123 made it!(author)2011-11-29

How could he not know that >_>
no wonder your a pro :) I know I know

author
FlutterTree made it!(author)2011-12-09

I like proper grammar, that's probably why I didn't know.

author
jnguyen5 made it!(author)2011-08-18

i made mine go 55 ft
mine went through a card board box and the rod wasnt sharpened, awesome gun.

author
FlutterTree made it!(author)2011-08-29

Thanks, mine didn't go very far but probably because my elastics were bad.

author
FlutterTree made it!(author)2010-12-22

Thanks for rating

author
Dawson.J made it!(author)2010-10-09

it looks like you can mod it so there is a clip in the handle. (if so please try)

author
FlutterTree made it!(author)2010-11-14

I'll try that and see if it works.

author
TheKnexNoob made it!(author)2010-10-24

nice, might make this later

author
automan97 made it!(author)2010-08-10

im new wat is that on the end of the ram

author
FlutterTree made it!(author)2010-08-11

That's a ball joint connector covered in electrical tape. If you don't have one than you can cut an orange connector in half

author
%7EKGB%7E made it!(author)2010-06-27

most pistols are exact same

author
FlutterTree made it!(author)2010-06-28

What ones?

author
TwistedParadox made it!(author)2010-06-28

Almost every TDS knock off

author
FlutterTree made it!(author)2010-06-29

How does this look like a TDS?

author
TwistedParadox made it!(author)2010-06-29

The handle + clip, it's the same

author
FlutterTree made it!(author)2010-06-29

The handles look nothing alike, and this is a single shot.

author
TwistedParadox made it!(author)2010-06-29

The snowflakes not actually touching but being held inplace by the bits on the side?

author
FlutterTree made it!(author)2010-06-29

HUNDREDS of knex gun handles are like that.

author
TwistedParadox made it!(author)2010-06-30

where did it originate from though?

author
FlutterTree made it!(author)2010-07-01

I dunno.

author
%7EKGB%7E made it!(author)2010-06-28

finally somone agrees... thank you!

author
%7EKGB%7E made it!(author)2010-06-28

look around at nearly EVERY pistol...

author
jamesdude made it!(author)2010-06-26

not bad.... 1st comment!

author
FlutterTree made it!(author)2010-06-27

Thanks.

author
%7EKGB%7E made it!(author)2010-06-26

been done b4

About This Instructable

4,465views

9favorites

License:

Bio: Typical deadmau5-inspired electronic music artist. Not doing anything good at the moment, mainly experimental crap and Sytrus fuckery.
More by FlutterTree:Knex PistolPaper Airplane: The Nakamura LockK'nex Flatbed Truck
Add instructable to: