Print PDF
Favorite
Email
This instructable has been removed by the author.
19
comments
|
Add Comment
|
May 30, 2010. 2:14 PMprodo123 (author)
says:
The newest version is here :
http://www.instructables.com/id/SR70A1-PSRS/
This slideshow will be deleted in a week.
http://www.instructables.com/id/SR70A1-PSRS/
This slideshow will be deleted in a week.
May 25, 2010. 8:09 PMlphillips094
says:
yes
yes
and yes
make the instructable
i have made many knex guns and all i need is a sniper and this is the coolest one i have eva seen
do it!!!
yes
and yes
make the instructable
i have made many knex guns and all i need is a sniper and this is the coolest one i have eva seen
do it!!!
May 26, 2010. 12:30 PMprodo123 (author)
says:
Srry. SR70A1, the new version will be up very soon.
Who are you kidding? This gun looks rather sloppily put together, and I can tell from experience this is flimsy. The frame around the barrel is too barebones. It can't be any harder to build than the untangle, which is more powerful than this. The long barrel you have will actually reduce the power you have.
Just my criticism.
Just my criticism.
Mar 13, 2010. 7:27 PMprodo123 (author)
says:
Also, the bendy rods absorb impacts very well, so it's actually quite sturdy. The barrel sometimes needs to be moved and adjusted, but overall it rarely breaks.
If a gun is built properly, it wont need to have any shock absorbers to survive a fall. In my experience bendies make guns less sturdy.
Mar 15, 2010. 12:11 PMprodo123 (author)
says:
It has bendies on a stiff frame, so it's quite sturdy. The only part that needs improvement is the triggerguard. If you could, could you improve it?
Also, instructions are up:
http://www.instructables.com/id/Knex-Sniper-Rifle-SR-70-Instructions/
Also, instructions are up:
http://www.instructables.com/id/Knex-Sniper-Rifle-SR-70-Instructions/
Mar 13, 2010. 5:25 PMprodo123 (author)
says:
Actually, that's what the K'nexecutioner system does. It moves the real barrel up to the front, while the hammer is all the way back. There are "transfer rods" inside the "fake barrel" that deliver the hammer's force up to the front, and the bullet, which is all the way in the front, is fired. It's just like a chain reaction.
The knexecutioner doesn't do that, it just has a ram which slides down the barrel and hits the ammo, it has NO transfer rods. Are you sure you aren't talking about the Knexsayer?
Mar 13, 2010. 9:00 PMprodo123 (author)
says:
Take a look at the Knexecutioner 2.01 Cyclone instructable, and the instructable for this gun.
And btw, your lego stuff is AMAZING.
And btw, your lego stuff is AMAZING.
Ah I see what you mean. I was looking at the original knexecutioner. The knexsayer and the TR use the mechanism better however.
What lego stuff? The only lego thing I posted was a guide. Sure I do have legos but I never use them these days.
What lego stuff? The only lego thing I posted was a guide. Sure I do have legos but I never use them these days.
Mar 12, 2010. 11:16 AMTwistedParadox
says:
It looks kinda like it was made out of scraps and it needs a bit of filling in.
Mar 13, 2010. 5:25 PMprodo123 (author)
says:
I just wanted it to be curved and comfortable to hold (and yes, it is very comfortable). If you want to fill it in, go ahead.
Mar 12, 2010. 3:33 AMTigerNod
says:
Looks great! I like the angled scope, I suppose it is very accurate. Too bad it has no magazine though.
 |
