How to make a LMFAO robot head>

Step 1: Materials and tool

Picture of Materials and tool
1 about 17 1/2 x 12 inch box
1 can of gold spray paint
1 cheap black running jacket
plastic wrap
black see through fabric
binder clips
hot glue gun
scissors or exacto knife
1-40 of 53Next »
164053 years ago
OMFG! Thank you for showing the WHOLE costume; not just the mask.
ethompson 164053 years ago
sebergast 164053 years ago
steveweal2 years ago
so it's 31/2 inches diameter for circles/eyes? and this is a great costume.
TChin1108 (author)  steveweal2 years ago
thanks and yea ... i used a 3 1/2" diameter soup can for the circles
ebello23 years ago
as you do to maintain that the box does not fall?
marts9093 years ago
how much did all of this cost?
laszlo103 years ago
how do you make the speedo
What did you use as the knobs on the side of the heads?
TChin1108 (author)  Dsanders20143 years ago
i rolled up some cardboard to make a cylinder and cut out a circle
were did you get thing for mouth
TChin1108 (author)  everydayimshufflen3 years ago
i just used some old black shorts and cut a rectangle
How do you see out of it????
throught the mouth
Ok so tomorrow is dress like a celebrity and my friends are Redfoo and Skyblu and I am robot guy and I dont know if i can wear the box thing. :(
flyboyangel3 years ago
wseevers3 years ago
I really thought you'd be in a speedo =(
You sound disappointed.
alowman3 years ago
how do you see
I believe you see through the mouth. :)
Is it very difficult to make ?
TChin1108 (author)  HalloJanice_3 years ago
not really as long as you have the supplies and you follow the direction
gwilliams133 years ago
what are the things on the side of the head? ive done it all and it looks great but i need to know how big and what they should be
TChin1108 (author)  gwilliams133 years ago
on the side are bolts that i made of leftover cardboard. i rolled up a strip of card and then glued a circle that was about 1 in. in diameter.
jongko3 years ago
now i can shuffle man
TChin1108 (author)  jongko3 years ago
cguerrero53 years ago
GREAT! this is what i was looking for. it look like the exact same robot head in party rock!
jfahey3 years ago
Put some EL Wire around it :)
dkim33 years ago
i needed a cool and easy to make costume asap! u saved me! thanks!
wseevers3 years ago
polyurethane spray foam :)
wseevers3 years ago
Dear Santa-
Flash Mob!!
julian213 years ago
thanks this helps so much!(: where can i get LED lights?
TChin1108 (author)  julian213 years ago
i used a maxsa safety wristband with blinking LEDs and i took them out, but you probably not going to be able to get them unless shipped next day air. so you could just use a light stick from party city or something
dhooper3 years ago
about what are the dimensions of the box you used
TChin1108 (author)  dhooper3 years ago
about 17x11 1/2x9 " its like one of those office paper boxes. I'm not really sure where i got mine i just found it lying around, sorry if this doesn't help.
think it helps. thanks much, now i got all the stuff got to put it all together party Saturday.
how did u stabilize the head, mine flops everywhere
TChin1108 (author)  anhbuttercup3 years ago
To make it so that your head doesn't move around the box i used the leftover end i had cut off and taped down to surround my head so that it fit snug. If you want you can stuff paper inside to add some cushion. if you did that then just add some more paper as stuffing or cardboard so that it is tight. also you might want to make it go lower to your cheeks. use the image below and in step 3
ualcala3 years ago
where can you get that box cause i need to make one asap??
TChin1108 (author)  ualcala3 years ago
I'm not really sure where i got mine i just found it lying around, its an box that holds printer paper like the ones in an office
1-40 of 53Next »