Instructables

Laptop Bubble Stand

Featured
Picture of Laptop Bubble Stand
002.jpg
IMG_1109.JPG
004.jpg
Everyone is always making laptop stands that, albeit functional, are rather hideous to look at. This becomes less than ideal when you consider that typically, when the laptop is not on the stand, you have to look at it. I wanted to fix this problem by making a laptop stand that was sleek, stylish, inexpensive and kept my laptop cool. With this in mind, I arrived at wicked cool laptop stand that can be made for under $10. The best part is that not only is it cheap, but it's also dead easy to make.

Main image courtesy of Sarah.
 
Remove these adsRemove these ads by Signing Up

Step 1: Go get stuff

Picture of Go get stuff
IMG_1115.JPG
thumbnail.bmp
You will need:

A 16" x 16" sheet of 1/8" acrylic (this leaves a little room for margins/scrap)
A heat gun
A ruler
Oven mitts
Two table clamps
A workbench
Some plywood scrap
A laser cutter

(if you don't have a laser cutter, you can download the file in the next step and have a service like Ponoko cut it for you.)

Step 2: Prepare to cut

Picture of Prepare to cut
IMG_1063.JPG
IMG_1065.JPG
Peel the protective material off both sides of your acrylic. Position it correctly in the laser cutter and close the lid.

Download the file attached below and open it in Corel Draw.

Step 3: Cut

Picture of Cut
IMG_1067.JPG
I am using a 75 Watt Epilog laser cutter with the following print settings:

Cut type: Vector
Power: 100
Speed: 20
Frequency: 5000

To start cutting my material, I simply hit the green button on the machine and then babysit the machine for twenty minutes while it does its thing.
1-40 of 119Next »
manfredpw5 months ago

Simple idea and beautiful design.

But laser cutter, i don't know, so much expensive.

I think it's totally possible make it with other (less expensive) tools.

But i agree: very nice work.

Tks for sharing.

Daen, I left my laser cutter in my other pants!
Alrighttt - We have a reader with the right idea - let us see who among us can make an inexpensive instructable laser cutter. Can it be done? At a low cost and with our ingenuity?
If you were born in Planet Krypton, you could do it with your eyes.
randofo (author)  rwilliams2345 years ago
You must wear some pretty big pants. A laser cutter weighs a few hundred pounds.
The one in my mind is much lighter. It does not weigh anything.
MRedu2 years ago
This is by far the best laptop stand on instructables (there's a lot of them).
mvan heemst2 years ago
Can I buy one from you? I would like a clear one (not clear blue, just plain clear) I would buy one for $30 including shipping. You are right! No one else makes one that looks as good as yours.
What does the red button on the wall do. It makes me curious and I have the urge to press the button. On a side note great instructable
do you mean in like a tech ed room? do not push the button!!! it is an emergency elctrical button that if pushed will shut off power to the WHOLE room. like if someone gets their arm stuck in a woodchipper
my school's workshop has that. It reminds me off the game dont press the red button. BUT ITS SO TEMPTING TO PRESS THE RED BUTTOM
my school's workshop has one too, but it is so crap, you don't need the key to turn it on; you just push it down then pull out and hehy presto power!!
Has anyone used Ponoko to do the laser cutting yet? What kind of a price?
mg0930mg3 years ago
To everyone complaining about not having a laser cutter. Ask around, your local high school or college may have one, and cut it for you. Also search for laser cutting business on google. You may be able to find one near you. Good luck.

Randofo, great instructable, I love how it looks.
Not many laser cutters where I'm from, surprising considering my proximity to silicone valley!
Then it looks like you should go to ponoko or some similar service.
I have one. I'm in Colorado Springs. My Email is donaldpelton@gmail.com
BBurak3 years ago
Really perfect. Good luck with your works.
pingo63 years ago
i dont think a laser cutter is under 10 bucks
randofo (author)  pingo63 years ago
You don't already have one?
pingo6 randofo3 years ago
why would i? i dont really need one. plus you cant cut stuff too thick.
ultrauber5 years ago
If you didn't have a laser cutter, you could just use gigantic drill bits, right?
You could probably use hole saws.
Yes, but be REALLY careful... Don't want it to crack...
big-jamie5 years ago
i just have one question...where did you get a laser cutter and how much are they ? =)
Check the epilog site linked above. Around 3,000+ dollars. And that's cheap for most lasers.
(removed by author or community request)
You can't spell...or read.
It said for most lasers.
ok well im sorry. all i said was: "ya, $3000, real cheap!" u ddnt need 2 comment on tht at all.
PS: i accidentally clicked remove above 4 the comment so ya thts y it says "removed by author or community request"
You didn't need to comment on this either, then why did you? That's a stupid point to bring up.
j03tv3 years ago
Please put "Using a laser cutter" in the title of your instructable. Most people dont have a laser cutter which makes this project far from affordable and nowhere near $10/
anres321 j03tv3 years ago
I aggree :D
randofo (author)  j03tv3 years ago
As it states in step 1:

(if you don't have a laser cutter, you can download the file in the next step and have a service like Ponoko cut it for you.)

Again, that is ponoko.com. It may cost slightly more than $10 to have them cut it, but not much more.

I'm not going to put it in the title. I don't have a welder, but I don't go around complaining on every single welding projects that I don't have the tool and it needs to be branded as such. If I want something welded, then I figure out how to get access to a welder or have someone weld it for me. I don't go around complaining to the person who has made something with their welder about how I can never do their project because I don't own one.
Templarix474 years ago
Under $10? How bout the laser?
randofo (author)  Templarix474 years ago
I already had the laser, heat gun and clamps. Doesn't everyone?
x z i t randofo4 years ago
nobody has a laser cutter!
Nope! That's just me but how bout everybody else who doesnt have those things? Just buy those just to make a laptop stand and then never use them again? But still cool instructable.
Ive been looking at laptop stands and ive had the same problem as you there all ugly !

Im going to cut one like this but at the back im going to cut room for 4 usb ports (from a usb hub) a fan and a wireless card antenna Hopefully ! 

Now to bribe our schools Technology teacher to let me use the laser cutter , Shouldnt be too hard
How to persuade a tech teacher.
Pick one:
A: $500 cash.
B: Give them the latest piece of Japanese tech.
C: Hit them with a $10 wrench.
 Sounds like C is the most effective (and cheapest) option!
1-40 of 119Next »