Instructables
Picture of Laser Cut Table
A flat packable side table for the temporarily furniture-less nomad.

Laser cut furniture!
 
Remove these adsRemove these ads by Signing Up

Step 1: Design

Picture of Design
If not obvious, the intent is to make this table appear to look like the cutaway of an unguided bomb.

The table is made from three pieces - the base (2 parts) and a top.

I left some holes in the center area to allow an alarm clock cord to pass through.

Step 2: Laser Cut!

Picture of Laser Cut!
P1010189.JPG
Attached is a DXF File of the parts.

You should cut/chop and scale the file to fit your equipment.


For the curious, the girl hugging the bomb is a Banksy piece as seen here.

Step 3: Assemble

Picture of Assemble
You put the lime in the coconut and shake them all up.

The base parts slip into each other. The top fits as seen in the intro step. Everything is held by friction.


My feedback is - this table is a little tall to be used  as a night stand unless you're sleeping in a hammock. In case of hammock, be sure to place the table far enough away as not to knock it while swinging about.

Step 4: Move House

Picture of Move House
When it's time to move, disassemble and flat pack.

A few bits of tape will hold the parts together safely.

Currently this table lives in it's flat pack form as my new room does not have a space for this table. Perhaps in my next move it will have a home.
23104012 days ago

hjj

Hello, I am new the the group and own a 60 watt ULS with a 24" x 18" bed, I have COREL DRAW X5, can some send this file in that format? or post it? I am not capable of using nor understanding DXF Files. I purchased some 1/4" Birch plywood for this project and hope it works ok. Also, I am new to the laser engraver and would like to adjust for the KERF for this project (I am using a 2.0" fl optics).
jack ruby2 years ago
Is there anyone in the bay area that rents time on laser cutters or CNC routers? Does the place you made your table ?
There is this new place called http://www.laserbuilt.com in San Francisco
Late reply but there absolutely is a place you can laser stuff. Techshop! Locations in San Jose, Menlo Park, and San Francisco. Check out Techshop.ws

I just signed up again after a long hiatus and its great. If you sign up, tell them Taylor Alexander referred you and I'll get a nice free class coupon. :)

For the lazier among us, Ponoko in Oakland will laser stuff for you and mail it your way.
My friend's company got a Trotec Laser Cutter Speedy 500. Do you think it is possible to make such a table with this laser machine too?
I am impressed with this. What width of material did you use. That would be key to getting it to fit together. You do not say in the instructable
trebuchet03 (author)  Wynfordeagle3 years ago
Material is roughly .2 inches.... I didn't specify as your material may be different and your cutting setup will most likely be different - you'll have to tweak/scale/modify to fit your needs.
I also wanted to ask does the file also contain the instruction to print the artwork as I have downloaded the file and opened it in Solidworks eDrawings but I do not see artwork of the girl
trebuchet03 (author)  Wynfordeagle3 years ago
No artwork - just the mechanical profiles....

I'll have to track down the file I used to actually cut - I can't remember where it ended up...
drgn3693 years ago
I like it simple functional and a clean design I will just have to figure out how to make it with the high tech tools
Virus273 years ago
gosh i wish i had that type of equipment.... i'm a military graphic artist, but i don't have the equipment or the money to do these kinds of projects but would love to.....

P.S. great design!
Thank you for your service.

Is there a hobby shop at your base? My last base had a pretty decent one with hourly rentals of space and equipment, as well as people who could give advice (but not touch projects). I used the auto part mostly, but the prices were very reasonable, even as an E2.
dulciquilt3 years ago
I have been trying to design something similar to this, just a simple pyramid, to use as pedestals at an art gallery. I doubt most people would recognize the bomb and it has very nice lines. I need something I can store in the van and set up/take down quickly. This is perfect.
thepelton3 years ago
I also noticed that you said your favorite number is 42.

Have you read "Hitchhiker's Guide to the Galaxy", by Adams?
trebuchet03 (author)  thepelton3 years ago
Indeed - required reading for those that want to increase their not-yet-invented word vocabulary (of which, there's a dictionary - "The meaning of Lff" and "The (greater) meaning of Liff")

I've recently read "Last To See" which is a Nonfiction by Adams, and still hilarious and then a little sad as at least one of the species in the book has since gone extinct (that book is 20 years old :p).

I'm going to start "The Long Dark Tea-Time of the Soul" soon too but, I want to finish some Philip K. Dick stories first....
"Only Apparrently Real" is a biography in interviews of P.K. Dick. I reccommend it.
Love it! Fantastic design.
thepelton3 years ago
Hmm. Interesting. How big is the working area in your laser? Sounds like it must be a lot larger than the one I have been using. I made an adirondack chair that might fit a barbie doll.
trebuchet03 (author)  thepelton3 years ago
It's an Epilog Legend EXT 75

36"x24"

You should totally post the chair :)
My laser is a little 12x18.

I like the idea of posting the directions for the chair. Maybe I can make it Instructable number two.

8>)
trebuchet03 (author)  thepelton3 years ago
Do it!

Smaller bed space just means you'll have to have more parts that get assembled... There's nothing wrong with machine screws - make it a feaature of the design :)
what is it made out of? did you laser burn the design into the table?
trebuchet03 (author)  ninjarider5003 years ago
Luan Plywood. I just measured - it's about .2 inches thick but I believe (IIRC) it was sold as 3/16" thick. A place like Home Depot may sell it as "Sandply."

The graphic was laser etched :)
I used 3mm, or 1/8 inch Baltic Birch plywood. It's available in lumberyards in 5 foot by 5 foot squares. (153cmx153cm) for about twenty five bucks. It's cheaper if you don't have to have it cut down to put in the car, which I do. (2001 Dodge Neon).
I LOVE IT, the table and the chosen art work - purfecto!
canida3 years ago
Nice table!

Welcome back to the land of the posting, by the way. It's been too long.
Agreed, good to see you again T.
arale3 years ago
great design!
thepelton3 years ago
I can upload a picture of that chair.
image0-2.jpg
Culturespy3 years ago
I'd been looking at the base of that table in the workshop trying to figure out what it is! Well done! Wouldn't have guessed you were making a table.
Pro

Get More Out of Instructables

Already have an Account?

close

PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!