Introduction: Make Operation Boardgame Into Shocking Paris Hilton Operation

Picture of Make Operation Boardgame Into Shocking Paris Hilton Operation

This is an easy soldering project that makes operation shock people instead of just make noise or vibrate when you mess up! Fun and less than $10 if you already have the board game.

Step 1: What You Need:

Soldering Iron Stuff (Electrical tape, soldering iron, solder, wire, tester, etc)
Operation board game (I used the Simpsons edition)
FK901. Low Power Electric Shock Kit found @ online stores for about 4$
9V Batt
Printing capabilities for the Paris Hilton overlay

Step 2: The Printed Overlay Application

Picture of The Printed Overlay Application

This is the image file i made and printed out on photopaper. You cut out the black places. You can lay it right over Homer or you can take the Homer off. (Thats what i did) Then I adhered the paper to the top of the boardgame with permanent dbl stick tape.

Step 3: Solder Up the Shock Kit

Picture of Solder Up the Shock Kit

When puting together the kit don't solder the thumbtacks into the board. Instead run one wire from each of them. One of those wires goes to the bottom of the metal sheet (orange). The other i ran up to where the original wire comes out of the board (green). Drill a small hole for the wire to prodrude.

Step 4: Lastly, Connect the Wire Too the Pincher

Picture of Lastly, Connect the Wire Too the Pincher

In order to not complete the circuit continually i wrapped one side of the pincher with electrical tape. Then I put a size 11 exacto blade over the tape with the wire from the shocker wrapped arounf it at wrapped it with more tape.

Note: I mean no disrespect to Paris Hilton. Notice that she has a "Heart of Gold" in the game!

Comments

tdzurnak (author)2015-01-14

omg this is too awesomely funny,, have a long standing joke about Paris and sex..

Stephen P (author)2006-04-15

instead of using a "low power electric shocker"...why not use a disposable camera flash mechanism for a little more punishment! But that would be evil...

barri_kid (author)Stephen P2007-03-28

You want to be careful with those. I bought one, but I dont know the capacitance of it so id warn you about not using them. With out that knowledge you could burn yourself pritty badly

Loveofchaos (author)barri_kid2007-06-27

330v at 120uF (thats the highest rating from a kodak maxx i think.) it stays a straight 330v but ive seen from 80uF to 120uF to assume the worst lol

heliosrising (author)Loveofchaos2007-11-17

that would hurt, to say the least

Loveofchaos (author)heliosrising2007-11-18

yeah... thats why ive never shocked meself with them.... not to say i havent tried with lower voltages lol

heliosrising (author)Loveofchaos2007-11-19

thinking back, I realize that I did actually do that. I was making a coilgun. my pinky finger got too close to the capacitor. the burn looked just like the scars on Heroes, you know, the ones that are two black stripes side by side.

girrrrrrr2 (author)Stephen P2007-07-26

just have it make the flash go off... that would work fine for some...

linkspast (author)Stephen P2006-09-22

That be awsome!

Nbalmer (author)Stephen P2006-04-23

then no one would play. but maybe i should do that and let it have 2 modes.

barri_kid (author)2007-03-28

Nice! where did u get that shock kit? Do u know what cap and resistor is in it?

Nbalmer (author)barri_kid2007-03-28

i got it at http://store.qkits.com/moreinfo.cfm/FK901 you can find the same kit in other stores online as well.

sheltabrisk (author)2007-03-23

she is fashion model indust in top level.It looks like the Homer Simpson edition

she is fashion model indust in top level.It looks like the Homer Simpson Paris_Hilton wallapapersedition

lewiso1 (author)2007-01-12

How does a shocker work? Wouldn't the current just go through the metal prongs, since people's fingers have too much resistance?

CrazyCory564 (author)lewiso12007-02-15

The human body (including the epidermis aka skin) is made up of atleast 74% water, usually more. Water is an electrical conductor, and due to that skin is not a good resisting force against electrical shocks.

lemonie (author)CrazyCory5642007-02-25

Pure water is a poor electical conductor, but we're also loaded up with Na, K, carbonate & other ions, which make a difference.

robodud3 (author)2007-02-18

i love ripping off the front paper thing on those games then sticking the tweezers on the motor in the top corner it makes lots and lots of big huge geynormas spaks that go everywhere

sk8terboi1093 (author)2006-11-24

funny and cule at the same time hellz yea

guerroloco (author)2006-04-19

Spray adhesive such as Super 77, properly applied, would be a better way of sticking the photo to the board

blfinche (author)2006-03-10

It looks like the Homer Simpson edition

Nbalmer (author)blfinche2006-03-19

Yeah, it is.

fangorn81 (author)2006-03-09

what version of operation is that? The organs don't line up with any operation board images I can find on line. Is it the travel edition?

blfinche (author)fangorn812006-03-10

I think it is the Homer Simpson edition

dan (author)2006-02-15

we're working on allowing access to the high-res original images, in the meantime you can upload the high-resolution image for others to download if you zip it first

About This Instructable

15,507views

17favorites

License:

More by Nbalmer:Wii Zapper DIY Airsoft Mod Make Operation boardgame into shocking Paris Hilton Operation
Add instructable to: